FILE NO. 140-200312
DOCUMENT CREATED IN JAPAN, Apr., 2003
SERVICE MANUAL
COLOR TELEVISION
13A23W
SERVICING NOTICES ON CHECKING
As for the places which need special attentions,
they are indicated with the labels or seals on the
cabinet, chassis and parts. Make sure to keep the
indications and notices in the operation manual.
2. AVOID AN ELECTRIC SHOCK
There is a high voltage part inside. Avoid an
electric shock while the electric current is
flowing.
3. USE THE DESIGNATED PARTS
The parts in this equipment have the specific
characters of incombustibility and withstand
voltage for safety. Therefore, the part which is
replaced should be used the part which has
the same character.
Especially as to the important parts for safety
which is indicated in the circuit diagram or the
table of parts as a mark, the designated
parts must be used.
4. PUT PARTS AND WIRES IN THE
ORIGINAL POSITION AFTER
ASSEMBLING OR WIRING
There are parts which use the insulation
material such as a tube or tape for safety, or
which are assembled in the condition that
these do not contact with the printed board.
The inside wiring is designed not to get closer
to the pyrogenic parts and high voltage parts.
Therefore, put these parts in the original
positions.
5. TAKE CARE TO DEAL WITH THE
CATHODE-RAY TUBE
In the condition that an explosion-proof cathoderay tube is set in this equipment, safety is
secured against implosion. However, when
removing it or serving from backward, it is
dangerous to give a shock. Take enough care to
deal with it.
6. AVOID AN X-RAY1. KEEP THE NOTICES
Safety is secured against an X-ray by considering about the cathode-ray tube and the high
voltage peripheral circuit, etc.
Therefore, when repairing the high voltage peripheral circuit, use the designated parts and
make sure not modify the circuit.
Repairing except indicates causes rising of high
voltage, and it emits an X-ray from the cathoderay tube.
PERFORM A SAFETY CHECK AFTER
7.
SERVICING
Confirm that the screws, parts and wiring which
were removed in order to service are put in the
original positions, or whether there are the
portions which are deteriorated around the
serviced places serviced or not. Check the
insulation between the antenna terminal or
external metal and the AC cord plug blades.
And be sure the safety of that.
(INSULATION CHECK PROCEDURE)
1.
Unplug the plug from the AC outlet.
2.
Remove the antenna terminal on TV and turn
on the TV.
3.
Insulation resistance between the cord plug
terminals and the eternal exposure metal
[Note 2] should be more than 1M ohm by
using the 500V insulation resistance meter
[Note 1].
4.
If the insulation resistance is less than 1M
ohm, the inspection repair should be
required.
[Note 1]
If you have not the 500V insulation
resistance meter, use a Tester.
[Note 2]
External exposure metal: Antenna terminal
Earphone jack
HOW TO ORDER PARTS
Please include the following informations when you order parts. (Particularly the VERSION LETTER.)
1. MODEL NUMBER and VERSION LETTER
The MODEL NUMBER can be found on the back of each product and the VERSION LETTER can be
found at the end of the SERIAL NUMBER.
2. PART NO. and DESCRIPTION
You can find it in your SERVICE MANUAL.
IMPORTANT
Inferior silicon grease can damage IC's and transistors.
When replacing an IC's or transistors, use only specified silicon grease (YG6260M).
Remove all old silicon before applying new silicon.
A1-1
TABLE OF CONTENTS
SERVICING NOTICES ON CHECKING.....................................................................................
HOW TO ORDER PARTS ..........................................................................................................
IMPORTANT ...............................................................................................................................
TABLE OF CONTENTS..............................................................................................................
GENERAL SPECIFICATIONS ...................................................................................................
DISASSEMBLY INSTRUCTIONS
1. REMOVAL OF ANODE CAP ...............................................................................................
2. REMOVAL AND INSTALLATION OF FLAT PACKAGE IC ................................................
SERVICE MODE LIST ................................................................................................................
CONFIRMATION OF HOURS USED .........................................................................................
WHEN REPLACING EEPROM (MEMORY) IC ..........................................................................
ELECTRICAL ADJUSTMENTS..................................................................................................
BLOCK DIAGRAMS ...................................................................................................................
PRINTED CIRCUIT BOARDS
MAIN/CRT................................................................................................................................
MAIN ........................................................................................................................................
SCHEMATIC DIAGRAMS
MICON/CHROMA/TUNER ......................................................................................................
TV POWER..............................................................................................................................
DEFLECTION/CRT..................................................................................................................
SOUND/AV ..............................................................................................................................
WAVEFORMS .............................................................................................................................
MECHANICAL EXPLODED VIEWS...........................................................................................
MECHANICAL REPLACEMENT PARTS LIST .........................................................................
ELECTRICAL REPLACEMENT PARTS LIST...........................................................................
A1-1
A1-1
A1-1
A2-1
A3-1~A3-10
B1-1
B2-1, B2-2
C1-1
C1-1
C1-1
D-1~D-4
E-1, E-2
F-1, F-2
F-3, F-4
G-1, G-2
G-3, G-4
G-5, G-6
G-7, G-8
H-1, H-2
I-1
J1-1
J2-1~J2-3
A2-1
GENERAL SPECIFICATIONS
G-1 TV CRT CRT Size / Visual Size 13 inch / 335.4mmV
G-2 Tuning Broadcasting System US System M
G-3 Power Power Source AC 120V AC 60Hz
G-4 Regulation Safety UL / CSA
G-5 Temperature Operation +5oC ~ +40oC
G-6 Operating Humidity Less than 80% RH
System CRT Type Normal
Color System NTSC
Speaker 1Speaker
Sound Output MAX
NTSC3.58+4.43 /PAL60Hz No
System Tuner and System 1Tuner
Receive CH Destination USA(W/ CATV)
Intermediate Picture(FP) 45.75MHz
Frequency Sound(FS) 41.25MHz
Preset CH No
Stereo/Dual TV Sound No
Tuner Sound Muting Yes
Power Consumption at AC
Protector Power Fuse Yes
Deflection
Magnetic Field BV/BH +0.45G/0.18G
Position Bottom
Size 3 Inch
Impedance 8 ohm
10%(Typical)
Tuning System F-Synth
Input Impedance VHF/UHF 75 ohm
CH Coverage A - I, J - W, W+1 - W+84
FP-FS 4.50MHz
DC
Stand by (at AC)
Per Year
Radiation FCC / IC
X-Radiation DHHS / HWC
Storage -20oC ~ +60oC
90 degree
2 - 69, 4A, A-5 - A-1,
54 W at AC 120 V 60 Hz
5 W at AC 120 V 60 Hz
-- kWh/Year
1.0 W
0.8 W
A3-1
GENERAL SPECIFICATIONS
G-7 On Screen Menu Yes
G-8 OSD Language English French Spanish
Display Menu Type Character
Picture Yes
Contrast Yes
Brightness Yes
Color Yes
Tint Yes
Sharpness Yes
Audio No
Bass No
Treble No
Balance No
BBE On/Off No
Stable Sound On/Off No
CH Set Up Yes
TV/CABLE(CATV) Yes
Auto CH Memory Yes
Add/ Delete Yes
Language Yes
V-chip Yes
Lock Yes
On Timer Yes
CH Label No
Favorite CH No
Color Stream DVD/DTV No
Control Level Yes
Volume Yes
Brightness Yes
Contrast Yes
Color Yes
Tint Yes
Sharpness Yes
Tuning No
Bass No
Treble No
Balance No
Back Light No
Stereo,Audio Output,SAP No
Video Yes
Color Stream No
Channel(TV/Cable) Yes
CH Label No
Game Timer Yes
Sleep Timer Yes
Sound Mute Yes
V-chip Rating Yes
G-9 Clock and Sleep Timer Max Time 120 Min
Timer Step 10 Min
On Timer Program(On Timer ) Yes
Wake Up Timer No
Timer Back-up (at Power Off Mode) more than -- Min Sec
A3-2
GENERAL SPECIFICATIONS
G-10 Remote Unit RC-EH
Control Glow in Dark Remocon Yes
Format Toshiba
Custom Code
Power Source Voltage(D.C) 3V
UM size x pcs UM-4 x 2 pcs
Total Keys 27 Keys
Keys Power Yes
1 Yes
2 Yes
3 Yes
4 Yes
5 Yes
6 Yes
7 Yes
8 Yes
9 Yes
0 Yes
100 No
CH Up Yes
CH Down Yes
Volume Up Yes
Volume Down Yes
TV/Caption/Text Yes
CH1/CH2 Yes
TV/Video(TV/AV) Yes
CH RTN/CH ENT(Quick View) Yes
Sleep Yes
RE Call(Call) Yes
Reset Yes
Menu Yes
Enter Yes
Mute Yes
Exit No
MTS(Audio Select) No
Set + Yes
Set - Yes
Multi Brand Keys CH Up(VCR) No
CH Down(VCR) No
Pause/Still No
TV/VCR(VCR) No
Code No
FF No
Rew No
Rec No
Play No
Stop No
TV No
VCR No
Cable No
40-BF h
A3-3
GENERAL SPECIFICATIONS
G-11 Features Auto Degauss Yes
G-12 Accessories Owner's Manual Language English / Spanish / French
Auto Shut Off Yes
Canal+ No
CATV Yes
Anti-theft No
Rental No
Memory(Last CH) Yes
Memory(Last Volume) Yes
V-Chip Yes
BBE No
Auto Search No
CH Allocation No
SAP No
Channel Lock No
Just Clock Function No
Game Position No
CH Label No
VM Circuit No
Full OSD No
Premiere No
Comb Filter No
Auto CH Memory Yes
Hotel Lock No
Closed Caption Yes
FBT Leak Test Protect Yes
CH Lock Yes
Video Lock Yes
Game Timer (Max Time:120 Min) Yes
Stable Sound No
Energy Star No
Power On Memory Yes
Favorite CH No
Remote Control Unit Yes
Rod Antenna
Loop Antenna
U/V Mixer
DC Car Cord (Center+)
Guarantee Card
Warning Sheet
Circuit Diagram
Antenna Change Plug
Service Facility List
Important Safeguard
Dew/AHC Caution Sheet
AC Plug Adapter
Quick Set-up Sheet
Battery Yes
AC Cord
AV Cord (2Pin-1Pin)
Registration Card (NDL Card) Yes
ESP Card Yes
300 ohm to 75 ohm Antenna Adapter
Type USA,ORION Type
Lines
w/Guarantee Card Yes
Poles
Terminal
Terminal -
UM size x pcs UM-4 x 2 pcs
OEM Brand
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
A3-4
GENERAL SPECIFICATIONS
dges / 6 Surfaces
G-13 Interface Switch Front Power Yes
Rear AC/DC No
Indicator Power
Terminals Front Video Input
Rear Video Input(Rear1) No
G-14 Set Size Approx. W x D x H (mm)
G-15 Weight Net (Approx.)
G-16 Carton Master Carton
Gift Box Yes
Drop Test
Container Stuffing 866
G-17 Cabinet Material Cabinet Cabinet Front PS 94V0 DECABROM
PCB Non-Halogen Demand
System Select No
Main Power SW No
Sub Power No
Channel Up/Reset Yes
Channel Down/Enter Yes
Volume Up/Set Up Yes
Volume Down/Set Down Yes
MENU=Volume Up+Volume Down Yes
TV/CATV Selector No
Degauss No
Main Power SW No
Stand-by No
On Timer No
Audio Input
Other Terminal
Video Input(Rear2) No
Audio Input(Rear1) No
Audio Input(Rear2) No
Video Output No
Audio Output No
Euro Scart No
Color Stream No
Diversity No
Ext Speaker No
DC Jack 12V(Center +) No
VHF/UHF Antenna Input
AC Outlet No
Gross (Approx.)
Content ----
Material --
Dimensions W x D x H(mm) -- x -- x --
Description of Origin
Material Double/Brown
Dimensions W x D x H(mm)
Design As per Buyer's
Description of Origin Yes
Height (cm) 62
Cabinet Rear PS 94V0 DECABROM
Eyelet Demand Yes
Yes
RCA
RCA x 1
Ear Phone
F Type
362 x 360 x 320.5
9.5 kg
11.0kg
440 x 408 x 380
Natural Dropping At 1 Corner / 3
( 20.9 lbs)
( 24.4lbs)
No
Sets
/--
No
E
Sets/40' container
No
A3-5
GENERAL SPECIFICATIONS
G-1 TV CRT CRT Size / Visual Size 13 inch / 335.4mmV
G-2 Tuning Broadcasting System US System M
G-3 Power Power Source AC 120V AC 60Hz
G-4 Regulation Safety UL / CSA
G-5 Temperature Operation +5oC ~ +40oC
G-6 Operating Humidity Less than 80% RH
System CRT Type Normal
Color System NTSC
Speaker 1Speaker
Sound Output MAX
NTSC3.58+4.43 /PAL60Hz No
System Tuner and System 1Tuner
Receive CH Destination USA(W/ CATV)
Intermediate Picture(FP) 45.75MHz
Frequency Sound(FS) 41.25MHz
Preset CH No
Stereo/Dual TV Sound No
Tuner Sound Muting Yes
Power Consumption at AC
Protector Power Fuse Yes
Deflection
Magnetic Field BV/BH +0.45G/0.18G
Position Bottom
Size 3 Inch
Impedance 8 ohm
10%(Typical)
Tuning System F-Synth
Input Impedance VHF/UHF 75 ohm
CH Coverage A - I, J - W, W+1 - W+84
FP-FS 4.50MHz
DC
Stand by (at AC)
Per Year
Radiation FCC / IC
X-Radiation DHHS / HWC
Storage -20oC ~ +60oC
90 degree
2 - 69, 4A, A-5 - A-1,
54 W at AC 120 V 60 Hz
5 W at AC 120 V 60 Hz
-- kWh/Year
1.0 W
0.8 W
A3-6
GENERAL SPECIFICATIONS
G-7 On Screen Menu Yes
G-8 OSD Language English French Spanish
Display Menu Type Character
Picture Yes
Contrast Yes
Brightness Yes
Color Yes
Tint Yes
Sharpness Yes
Audio No
Bass No
Treble No
Balance No
BBE On/Off No
Stable Sound On/Off No
CH Set Up Yes
TV/CATV Yes
Auto CH Memory Yes
Add/ Delete Yes
Language Yes
V-chip Yes
Lock Yes
On Timer Yes
CH Label No
Favorite CH No
Color Stream DVD/DTV No
Control Level Yes
Sound Yes
Brightness Yes
Contrast Yes
Color Yes
Tint Yes
Sharpness Yes
Tuning No
Bass No
Treble No
Balance No
Back Light No
Stereo,Audio Output,SAP No
Video Yes
Color Stream No
Channel(TV/Cable) Yes
CH Label No
Game Timer Yes
Sleep Timer Yes
Sound Mute Yes
V-chip Rating Yes
G-9 Clock and Sleep Timer Max Time 120 Min
Timer Step 10 Min
On Timer Program(On Timer ) Yes
Wake Up Timer No
Timer Back-up (at Power Off Mode) more than -- Min Sec
A3-7
GENERAL SPECIFICATIONS
G-10 Remote Unit RC-EH
Control Glow in Dark Remocon Yes
Format Toshiba
Custom Code
Power Source Voltage(D.C) 3V
UM size x pcs UM-4 x 2 pcs
Total Keys 27 Keys
Keys Power Yes
1 Yes
2 Yes
3 Yes
4 Yes
5 Yes
6 Yes
7 Yes
8 Yes
9 Yes
0 Yes
100 No
CH Up Yes
CH Down Yes
Volume Up Yes
Volume Down Yes
TV/Caption/Text Yes
CH1/CH2 Yes
TV/Video(TV/AV) Yes
CH RTN/CH ENT(Quick View) Yes
Sleep Yes
RE Call(Call) Yes
Reset Yes
Menu Yes
Enter Yes
Mute Yes
Exit No
MTS(Audio Select) No
Set + Yes
Set - Yes
Multi Brand Keys CH Up(VCR) No
CH Down(VCR) No
Pause/Still No
TV/VCR(VCR) No
Code No
FF No
Rew No
Rec No
Play No
Stop No
TV No
VCR No
Cable No
40-BF h
A3-8
GENERAL SPECIFICATIONS
G-11 Features Auto Degauss Yes
G-12 Accessories Owner's Manual Language English / Spanish / French
Auto Shut Off Yes
Canal+ No
CATV Yes
Anti-theft No
Rental No
Memory(Last CH) Yes
Memory(Last Volume) Yes
V-Chip Yes
BBE No
Auto Search No
CH Allocation No
SAP No
Channel Lock No
Just Clock Function No
Game Position No
CH Label No
VM Circuit No
Full OSD No
Premiere No
Comb Filter No
Auto CH Memory Yes
Hotel Lock No
Closed Caption Yes
FBT Leak Test Protect Yes
CH Lock Yes
Video Lock Yes
Game Timer(Max Time:120 Min) Yes
Stable Sound No
Energy Star No
Power On Memory Yes
Favorite CH No
Remote Control Unit Yes
Rod Antenna
Loop Antenna
U/V Mixer
DC Car Cord (Center+)
Guarantee Card
Warning Sheet
Circuit Diagram
Antenna Change Plug
Service Facility List
Important Safeguard
Dew/AHC Caution Sheet
AC Plug Adapter
Quick Set-up Sheet
Battery Yes
AC Cord
AV Cord (2Pin-1Pin)
Registration Card (NDL Card) Yes
ESP Card Yes
300 ohm to 75 ohm Antenna Adapter
Type USA,ORION Type
Lines
w/Guarantee Card Yes
Poles
Terminal
Terminal -
UM size x pcs UM-4 x 2 pcs
OEM Brand
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
A3-9
GENERAL SPECIFICATIONS
dges / 6 Surfaces
G-13 Interface Switch Front Power Yes
Rear AC/DC No
Indicator Power
Terminals Front Video Input
Rear Video Input(Rear1) No
G-14 Set Size Approx. W x D x H (mm)
G-15 Weight Net (Approx.)
G-16 Carton Master Carton
Gift Box Yes
Drop Test
Container Stuffing 866
G-17 Cabinet Material Cabinet Cabinet Front PS 94V0 DECABROM
PCB Non-Halogen Demand
System Select No
Main Power SW No
Sub Power No
Channel Up/Reset Yes
Channel Down/Enter Yes
Volume Up/Set Up Yes
Volume Down/Set Down Yes
MENU=Volume Up+Volume Down Yes
TV/CATV Selector No
Degauss No
Main Power SW No
Stand-by No
On Timer No
Audio Input
Other Terminal
Video Input(Rear2) No
Audio Input(Rear1) No
Audio Input(Rear2) No
Video Output No
Audio Output No
Euro Scart No
Color Stream No
Diversity No
Ext Speaker No
DC Jack 12V(Center +) No
VHF/UHF Antenna Input
AC Outlet No
Gross (Approx.)
Content ----
Material --
Dimensions W x D x H(mm) -- x -- x --
Description of Origin
Material Double/Brown
Dimensions W x D x H(mm)
Design As per Buyer's
Description of Origin Yes
Height (cm) 62
Cabinet Rear PS 94V0 DECABROM
Eyelet Demand Yes
Yes
RCA
RCA x 1
Ear Phone
F Type
362 x 360 x 320.5
9.5 kg
11.0kg
440 x 408 x 380
Natural Dropping At 1 Corner / 3
( 20.9 lbs)
( 24.4lbs)
No
Sets
/--
No
E
Sets/40' container
No
A3-10
DISASSEMBLY INSTRUCTIONS
1. REMOVAL OF ANODE CAP
Read the following NOTED items before starting work.
*
After turning the power off there might still be a potential
voltage that is very dangerous. When removing the
Anode Cap, make sure to discharge the Anode Cap's
potential voltage.
*
Do not use pliers to loosen or tighten the Anode Cap
terminal, this may cause the spring to be damaged.
REMOVAL
1. Follow the steps as follows to discharge the Anode Cap.
(Refer to Fig. 1-1.)
Connect one end of an Alligator Clip to the metal part of a
flat-blade screwdriver and the other end to ground.
While holding the plastic part of the insulated Screwdriver,
touch the support of the Anode with the tip of the
Screwdriver.
A cracking noise will be heard as the voltage is discharged.
GND on the CRT
3. After one side is removed, pull in the opposite direction to
remove the other.
NOTE
Take care not to damage the Rubber Cap.
INSTALLATION
1. Clean the spot where the cap was located with a small
amount of alcohol. (Refer to Fig. 1-3.)
Location of Anode Cap
Fig. 1-3
NOTE
Confirm that there is no dirt, dust, etc. at the spot where
the cap was located.
2.3.Arrange the wire of the Anode Cap and make sure the
wire is not twisted.
Turn over the Rubber Cap. (Refer to Fig. 1-4.)
Screwdriver
Alligator Clip
GND on the CRT
Flip up the sides of the Rubber Cap in the direction of the
2.
arrow and remove one side of the support.
(Refer to Fig. 1-2.)
Rubber Cap
CRT
Support
Support
CRT
Fig. 1-1
Fig. 1-2
4. Insert one end of the Anode Support into the anode button,
then the other as shown in Fig. 1-5.
Support
CRT
5.6.Confirm that the Support is securely connected.
Put on the Rubber Cap without moving any parts.
B1-1
Fig. 1-4
Fig. 1-5
DISASSEMBLY INSTRUCTIONS
2.
REMOVAL AND INSTALLATION OF
FLAT PACKAGE IC
REMOVAL
Put the Masking Tape (cotton tape) around the Flat
1.
Package IC to protect other parts from any damage.
(Refer to Fig. 2-1.)
NOTE
Masking is carried out on all the parts located within 10
mm distance from IC leads.
When IC starts moving back and forth easily after
3.
desoldering completely, pickup the corner of the IC using a
tweezers and remove the IC by moving with the IC
desoldering machine. (Refer to Fig. 2-3.)
NOTE
Some ICs on the PCB are affixed with glue, so be
careful not to break or damage the foil of each IC leads
or solder lands under the IC when removing it.
Blower type IC
desoldering
machine
Masking Tape
(Cotton Tape)
Heat the IC leads using a blower type IC desoldering
2.
IC
machine. (Refer to Fig. 2-2.)
NOTE
Do not add the rotating and the back and forth
directions force on the IC, until IC can move back and
forth easily after desoldering the IC leads completely.
Blower type IC
desoldering machine
Fig. 2-1
Tweezers
IC
Peel off the Masking Tape.4.
Absorb the solder left on the pattern using the Braided
5.
Shield Wire. (Refer to Fig. 2-4.)
NOTE
Do not move the Braided Shield Wire in the vertical
direction towards the IC pattern.
Fig. 2-3
Braided Shield Wire
Soldering Iron
IC
Fig. 2-2
IC pattern
Fig. 2-4
B2-1
DISASSEMBLY INSTRUCTIONS
INSTALLATION
Take care of the polarity of new IC and then install the new
1.
IC fitting on the printed circuit pattern. Then solder each
lead on the diagonal positions of IC temporarily.
(Refer to Fig. 2-5.)
Soldering Iron
Solder temporarily
Supply the solder from the upper position of IC leads
2.
sliding to the lower position of the IC leads.
(Refer to Fig. 2-6.)
Solder temporarily
Fig. 2-5
When bridge-soldering between terminals and/or the
4.
soldering amount are not enough, resolder using a Thin-tip
Soldering Iron. (Refer to Fig. 2-8.)
Thin-tip Soldering Iron
IC
Fig. 2-8
Finally, confirm the soldering status on four sides of the IC
5.
using a magnifying glass.
Confirm that no abnormality is found on the soldering
position and installation position of the parts around the IC.
If some abnormality is found, correct by resoldering.
NOTE
When the IC leads are bent during soldering and/or
repairing, do not repair the bending of leads. If the
bending of leads are repaired, the pattern may be
damaged. So, be always sure to replace the IC in this
case.
Soldering IronSolder
IC
Supply soldering
from upper position
to lower position
Fig. 2-6
Absorb the solder left on the lead using the Braided Shield
3.
Wire. (Refer to Fig. 2-7.)
NOTE
Do not absorb the solder to excess.
Soldering Iron
IC
Braided Shield Wire
Fig. 2-7
B2-2
SERVICE MODE LIST
This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily.
To enter the Service Mode, press both set key and remote control key for more than 1 second.
Set Key
VOL. (-) MIN
VOL. (-) MIN
VOL. (-) MIN
VOL. (-) MIN 8
VOL. (-) MIN
Remocon Key Operations
0
1
6
9
Releasing of V-CHIP PASSWORD and LOCK PASSWORD.
Initialization of the factory.
NOTE:
POWER ON total hours is displayed on the screen.
Refer to the "CONFIRMATION OF HOURS USED".
Can be checked of the INITIAL DATA of MEMORY IC.
Refer to the "WHEN REPLACING EEPROM (MEMORY) IC".
Writing of EEPROM initial data.
NOTE: Do not use this for the normal servicing.
Display of the Adjustment MENU on the screen.
Refer to the "ELECTRICAL ADJUSTMENT" (On-Screen Display Adjustment).
Do not use this for the normal servicing.
If you set a factory initialization, the memories are reset such as the channel setting,
and the POWER ON total hours.
CONFIRMATION OF HOURS USED
POWER ON total hours can be checked on the screen. Total hours are displayed in 16 system of notation.
NOTE: If you set a factory initialization, the total hours is reset to "0".
1.
Set the VOLUME to minimum.
2.
Press both VOL. DOWN button on the set and Channel
button (6) on the remote control for more than 1 second.
3.
After the confirmation of using hours, turn off the power.
ADDRESS DATA
INIT 00 50
CRT ON 0010
FIG. 1
Initial setting content of MEMORY IC.
POWER ON total hours.
= (16 x 16 x 16 x thousands digit value)
+ (16 x 16 x hundreds digit value)
+ (16 x tens digit value)
+ (ones digit value)
WHEN REPLACING EEPROM (MEMORY) IC
If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken to
ensure correct data settings while making reference to TABLE 1.
NOTE: No need setting for after INI 0F due to the adjustment value.
INI
+0 +1 +2 +3 +4 +5 +6 +7 +8 +9 +A +B +C +D +E +F
00 AA 05 90 D6 00 07
50 04 EB 46 07 B3 24 69 00
Table 1
1.
Enter DATA SET mode by setting VOLUME to minimum.
2.
Press both VOL. DOWN button on the set and Channel button (6) on the remote control for more than 1 second.
ADDRESS and DATA should appear as FIG 1.
3.
ADDRESS is now selected and should "blink". Using the VOL. UP/DOWN button on the remote, step through the ADDRESS
until required ADDRESS to be changed is reached.
4.
Press ENTER to select DATA. When DATA is selected, it will "blink".
5.
Again, step through the DATA using VOL. UP/DOWN button until required DATA value has been selected.
6.
Pressing ENTER will take you back to ADDRESS for further selection if necessary.
7.
Repeat steps 3 to 6 until all data has been checked.
8.
When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input.
After the data input, set to the initializing of shipping.
9.
Turn POWER on.
10.
Press both VOL. DOWN button on the set and Channel button (1) on the remote control for more than 1 second.
11.
After the finishing of the initializing of shipping, the unit will turn off automatically.
The unit will now have the correct DATA for the new MEMORY IC.
39
C-1
ELECTRICAL ADJUSTMENTS
1. ADJUSTMENT PROCEDURE
Read and perform these adjustments when repairing the
circuits or replacing electrical parts or PCB assemblies.
CAUTION
•
Use an isolation transformer when performing any service
on this chassis.
•
Before removing the anode cap, discharge electricity
because it contains high voltage.
•
When removing a PCB or related component, after
unfastening or changing a wire, be sure to put the wire
back in its original position.
•
When you exchange IC and Transistor for a heat sink,
apply the silicon grease on the contact section of the heat
sink. Before applying new silicon grease, remove all the
old silicon grease. (Old grease may cause damages to the
IC and Transistor.)
Prepare the following measurement tools for electrical
adjustments.
1. Oscilloscope
2. Digital Voltmeter
3. Pattern Generator
On-Screen Display Adjustment
1. In the condition of NO indication on the screen.
Press the VOL. DOWN button on the set and the Channel
button (9) on the remote control for more than 1 second to
appear the adjustment mode on the screen as shown in
Fig. 1-1.
2. BASIC ADJUSTMENTS
2-1: CUT OFF
1.
Adjust the unit to the following settings.
R.DRIVE=10, B.DRIVE=10, R.BIAS=64, G.BIAS=64,
B.BIAS=64, BRI.CENT=120, CONT.MAX=40.
2.
Place the set with Aging Test for more than 15 minutes.
3.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (01) on the remote control to
select "CUT OFF".
4.
Adjust the Screen Volume until a dim raster is obtained.
2-2: WHITE BALANCE
NOTE: Adjust after performing CUT OFF adjustment.
1.
Place the set with Aging Test for more than 10 minutes.
2.
Receive the gray scale pattern from the Pattern Generator.
3.
Using the remote control, set the brightness and contrast
to normal position.
4.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (10) on the remote control to
select “R. BIAS”.
5.
Press the CH. UP/DOWN button on the remote control to
select the “R. BIAS”, “G. BIAS”, “B. BIAS”, “R. DRIVE” or
“B. DRIVE”.
6.
Adjust the VOL. UP/DOWN button on the remote control
to whiten the R. BIAS, G. BIAS, B. BIAS, R. DRIVE, and
B. DRIVE at each step tone sections equally.
7.
Perform the above adjustments 5 and 6 until the white
color is looked like a white.
TV
00 OSD 15
Fig. 1-1
3.4.Use the Channel UP/DOWN button or Channel button
(0-9) on the remote control to select the options shown
in Fig. 1-2.
Press the MENU button on the remote control to end the
adjustments.
FUNCTION
NO.
OSD H
00
CUT OFF
01
H. VCO
04
H. PHASE
05
V. SIZE
06
V. SHIFT
07
R DRIVE
08
B DRIVE
09
R BIAS
10
G BIAS
11
B BIAS
12
BRIGHT CENT
13
BRIGHT MAX
14
BRIGHT MIN
15
FUNCTION
NO.
CONTRAST CENT
16
CONTRAST MAX
17
CONTRAST MIN
18
COLOR CENTER
19
COLOR MAX
20
COLOR MIN
21
TINT
22
SHARPNESS
23
FM LEVEL
24
LEVEL
25
SEPARATION1
26
SEPARATION2
27
TEST MONO
28
TEST STEREO
29
Fig. 1-2
2-3: FOCUS
1.
Receive the monoscope pattern.
2.
Turn the Focus Volume fully counterclockwise once.
3.
Adjust the Focus Volume until picture is distinct.
2-4: HORIZONTAL PHASE
1.
Receive the monoscope pattern.
2.
Using the remote control, set the brightness and contrast
to normal position.
3.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (05) on the remote control to
select “H. PHAS”.
4.
Press the VOL. UP/DOWN button on the remote control
until the SHIFT quantity of the OVER SCAN on right and
left becomes minimum.
2-5: VERTICAL SHIFT
1.
Receive the monoscope pattern.
2.
Using the remote control, set the brightness and contrast
to normal position.
3.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (07) on the remote control to
select “V. SFT”.
4.
Press the VOL. UP/DOWN button on the remote control
until the horizontal line becomes fit to the notch of the
shadow mask.
D-1
ELECTRICAL ADJUSTMENTS
2-6: VERTICAL SIZE
1.
Receive the monoscope pattern.
2.
Using the remote control, set the brightness and contrast
to normal position.
3.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (06) on the remote control to
select “V. SIZE”.
4.
Press the VOL. UP/DOWN button on the remote control
until the SHIFT quantity of the OVER SCAN on upside and
downside becomes 10 ± 2%.
2-7: SUB BRIGHTNESS
1.
Receive the monoscope pattern. (RF Input)
2.
Using the remote control, set the brightness and contrast
to normal position.
3.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (13) on the remote control to
select "BRI.CENT".
4.
Press the VOL. UP/DOWN button on the remote control
until the white 10% is starting to be visible
5.
Receive the monoscope pattern. (Audio Video Input)
6.
Press the TV/VIDEO button on the remote control to set
to the AV mode. Then perform the above adjustments
2~4.
2-8: SUB TINT/SUB COLOR
1.
Receive the color bar pattern.
2.
Connect the oscilloscope to TP023.
3.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (22) on the remote control to
select "TINT".
4.
Press the VOL. UP/DOWN button on the remote control
until the section "A" becomes as straight line
(Refer to Fig. 2-1)
5.
Connect the oscilloscope to TP022.
6.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (19) on the remote control to
select "COL.CENT".
7.
Press the VOL. UP/DOWN button on the remote control
until the red color level is adjusted to 110 ± 10% of the
white level. (Refer to Fig. 2-2)
8.
Receive the color bar pattern. (Audio Video Input)
9.
Press the TV/VIDEO button on the remote control to set
to the AV mode. Then perform the above adjustments
2~7
white 100%
2-9: SUB CONTRAST
1.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (17) on the remote control to
select “CONT. MAX”.
2.
Press the VOL. UP/DOWN button on the remote control
until the contrast step No. becomes “45”.
3.
Receive a broadcast and check if the picture is normal.
4.
Press the TV/VIDEO button on the remote control to set to
the AV mode. Then perform the above adjustments 1~3.
2-10: OSD HORIZONTAL
Activate the adjustment mode display of Fig. 1-1.
1.
Press the VOL. UP/DOWN button on the remote control
2.
until the difference of A and B becomes minimum.
(Refer to Fig. 2-3)
00 OSD 34
A
red 110%
TV
Fig. 2-2
B
Fig. 2-3
"A"
Fig. 2-1
D-2
ELECTRICAL ADJUSTMENTS
3. PURITY AND CONVERGENCE
ADJUSTMENTS
NOTE
1.
Turn the unit on and let it warm up for at least 30
minutes before performing the following adjustments.
2.
Place the CRT surface facing east or west to reduce the
terrestrial magnetism.
3.
Turn ON the unit and demagnetize with a Degauss Coil.
3-1: STATIC CONVERGENCE (ROUGH ADJUSTMENT)
1.
Tighten the screw for the magnet. Refer to the adjusted
CRT for the position. (Refer to Fig. 3-1)
If the deflection yoke and magnet are in one body,
untighten the screw for the body.
2.
Receive the green raster pattern from the color bar
generator.
3.
Slide the deflection yoke until it touches the funnel side
of the CRT.
4.
Adjust center of screen to green, with red and blue on
the sides, using the pair of purity magnets.
5.
Switch the color bar generator from the green raster
pattern to the crosshatch pattern.
6.
Combine red and blue of the 3 color crosshatch
pattern on the center of the screen by adjusting the pair
of 4 pole magnets.
7.
Combine red/blue (magenta) and green by adjusting the
pair of 6 pole magnets.
8.
Adjust the crosshatch pattern to change to white by
repeating steps 6 and 7.
3-2: PURITY
NOTE
Adjust after performing adjustments in section 3-1.
1.
Receive the green raster pattern from color bar generator.
2.
Adjust the pair of purity magnets to center the color on
the screen.
Adjust the pair of purity magnets so the color at the ends
are equally wide.
3.
Move the deflection yoke backward (to neck side)
slowly, and stop it at the position when the whole screen
is green.
4.
Confirm red and blue color.
5.
Adjust the slant of the deflection yoke while watching the
screen, then tighten the fixing screw.
DEFLECTION YOKE
DEFLECTION YOKE SCREW
MAGNET SCREW
3-3: STATIC CONVERGENCE
NOTE
Adjust after performing adjustments in section 3-2.
1.
Receive the crosshatch pattern from the color bar
generator.
2.
Combine red and blue of the 3 color crosshatch
pattern on the center of the screen by adjusting the pair
of 4 pole magnets.
3.
Combine red/blue (magenta) and green by adjusting the
pair of 6 pole magnets.
3-4: DYNAMIC CONVERGENCE
NOTE
Adjust after performing adjustments in section 3-3.
1.2.Adjust the differences around the screen by moving the
deflection yoke upward/downward and right/left.
(Refer to Fig. 3-2-a)
Insert three wedges between the deflection yoke and
CRT funnel to fix the deflection yoke.
(Refer to Fig. 3-2-b)
R G B
R
G
B
UPWARD/DOWNWARD SLANT RIGHT/LEFT SLANT
WEDGE WEDGE
WEDGE POSITION
R
G
B
Fig. 3-2-a
WEDGE
Fig. 3-2-b
R G B
PURITY MAGNETS
6 POLE MAGNETS
4 POLE MAGNETS
Fig. 3-1
D-3
ELECTRICAL ADJUSTMENTS
4. ELECTRICAL ADJUSTMENT PARTS LOCATION GUIDE (WIRING CONNECTION)
S101
CRT PCB
CP806
R803
R807
FB401
CP803A
CP803B
TU001
TP022
TP023
AC IN
CD501
DEGAUSS COIL
L503
CP502
S501B
S501A
T502
CP401
CRT DY
TP001
J801
CP802B
CP801
CD801
GND CRT
S102
CP802A
MAIN PCB
D-4
CD101A
CD101B
SPEAKER
BLOCK DIAGRAM
CH. DOWN
VOL. DOWN
CH. UP
VOL. UP
POWER
OS101
1
D106
J703
2
J702
Q105
SW
66
73
67
68
69
78
76
70
74
RGB Proc.2
OSD SW
CONTRAST BRIGHTNESS
I/O
IIC
TIM
INT
PWM
AD
RGB Proc.1
RGB MATRIX
COLOR CONT
ROM
RAM
TU00
1
OSD
10
11
MCU
CLK
12
13
17
21
Chroma Proc.
ACC/C-BPF
APC/KILLER
TINT/DEMO
20
Ver.Proc.
Ver SYNC SEP
Ver.COUNT DOWN
V RAMP
ATT
34
RGB OUTPUT Stage
DRIVE
CUT OFF
HV BLK
Hor.Proc.
SYNC SEPA/Hor. VCO
Hor.COUNT DOWN
AFC-1/H COINCIDENT
AFC-2 H PHASE
VCXO
50
51
52
46
45
IC1001 AN7511
2
SOUND AMP
IC
4
Q607
H-CTL
Q402
H. DRIVE
Q401
H. OUTPUT
7
6
EAR PHONE_JACK
J1001
2
6
SPEAKER
SP1001
8
Q801
RED OUT
Q802
GREEN OUT
Q803
BLUE OUT
Q505
P. FAIL
2
T502
16
8
6
Q503
PROTECT DRV.
4
13
IC501
LTV-817M-VB
FEED BACK
Q502
BUFFER
Q501
SWITCHING
Q507
FEED BACK
SW
D501~D504
RECTIFIER
26
27
56 16
58
6
5
SDA
DEGAUSS COIL
L503
2
1
F501
MEMORY IC
IC199
SCL
S-24C02BDP-1A
L501
4
3
57
38
37
V-OUT IC
IC401 AN5522
MICON/CHROM IC
IC101 OEC7091A
PUMP UP
AMP
+
VCC
75
1
26
X601
3.579545MHz
FB401
1
2
10
3
9
F
S
HV
DY
3
Heater
4
9
7
RGB
8
F
CRT
E-1
AC IN
E-2
PRINTED CIRCUIT BOARDS
MAIN/CRT (INSERTED PARTS )
SOLDER SIDE
C612
W058
W057
CP802A
Q607
W808
C614
D606
W059
W816
W055
W054
W053
S102A
W811
R608
R423
C605
W061
R614
R613
R615
CD101B
W060
W046
W833
R604
R606
R621
CD101A
C118
R601
W048
W831
C615
C616
C610
R701
C601
R602
X601
IC199
W050
W049
C606
C106
W056
C622
C624_1
J703
C602
C103
W052
W036
C617
W035
W051
Q602
R611
R110
J702
L001
Q601
W070
C633
R109
Q505
C628
R002
R516
R620
W042
R415
R001
W045
R616
W041
W039
W037
R445
Q603
R505
W832
W044
W008
W007
TU001
C434
D412
Q503
629
W023
W018
R607
W072
R416
R527
R523
R537
W034
W025
R119_1
W028
C123
C422
R130
R448
R449
D403
Q606
W065
W017
D604
W066
D001
W010
W009
C414
C507
D521
W024
W069
C621
C620_1
W033
R408
W062
W011
R409
R401
R413
R405
W038
C427
W015
R422
W834
R528
R
W067
W809
W040
W073
W823
W828
W068
C630
W043
W032
R617
W031
W030
R113
R112
SW101 SW102 SW103
R603
D603
R446
R424
W064
W803
C623
Q105
W029
C007
C004
IC401
C515
D514
C1003
R1001
D408
R418
W014
W012
R519
R605
C1001
W027
W026
R429
D411
R410
C440
Q402
D409
R417
C417
C418
C519
D522
IC1001
W813
W005
W020
C1005
C1008
D404
HS401
C446
R504
R447
C517_1
TP401
R525
CP803A
W002
CP401
T401
C516
C521
D510
D406
R515
Q507
CP601
W003
S101A
C443
D513
B504
C518
TP024
Q802
C809
R815
R811
D516
C808
R813
R809
C403
C437
W004
R517_1
C513_1
SW104
R427
D505
S102B
C410_1
D515
1
5_
80
R
R804
TP022
Q801
R816
C810
R814
CP802B
CP801
C406
R403
C435
R404
W006
R507
R802
D410
C
C448_1
TP023
Q803
420
D405
L401
HS402
D528
R513
R803_1
R806
C508
R518
W810
807_1
R
C401
FB401
Q401
D511
R512
R502
L801
CP806
W071
SW105
8V
W001
D512
180V
C511
C510
D508
T502
IC501
12V
R503
B501
R509
CP503
S101B
CP803B
C
819
ABL
25V
D506
D503
W802
TH501_1
GND
B+
HS501
R520
CP502
J801
R506
C509
R514
C503
R501
W019
AFC
C514
FH502
F501
FH501
R1007
OS101
HEATER
COL
W830
C526_1
S501A
R542
D509
Q502
Q501
R522
W819
R508
R510
D501
D502
C505
4A125VOR250V
R538
S501B
D106_1
D504
R421
R121
L501
J1001
C506
C502
R500
CD501
F-1
F-2
PRINTED CIRCUIT BOARDS
MAIN (CHIP MOUNTED PARTS)
SOLDER SIDE
R143
R128
R115
R101
R126
C112
R702R703
R704
C101
R618
C501_2
R1008
C1004_2
R1005
R420
R419
R1003
R1004
R116
R107
R106
R125
C629
R108
R124_1
R105
R127
R129
R610
C627
R609
C626
R627
41
25
C104
R103
C105
R102
C609
C107
C603
C108_1
R104
C604
IC101
64
1
C102
F-3
R003
R004
C001
F-4
8
G-1
G-2
7
1 CNVSS
2 XIN
3 XOUT
4 TEST1
5 VSS
6
6 MCU VCC
7 TEST0
8 FILT
9 HLT
10 VHOLD
11 CVIN
12 RESET IN
13 MCU RESET OUT
14 Y SW OUT
15 V/C GND
16 3.58 XTAL
17 C-APC
5
18 MCU5.7V REG OUT
19 NC
20 CVBS IN3
21 AUDIO IN3
22 V/C VCC
23 MCU TEST
24 CVBS IN2
25 AUDIO IN2
26 CVBS IN1
27 AUDIO IN1
28 5.7V REG OUT
29 C(Y/C) IN
30 Y(Y/C) IN
4
31 VREG VCC
32 FSC OUT
33 MONITOR OUT
34 AUDIO ATT OUT
35 AUDIO ATT FILTER
36 TEST 3
37 V RAMP F/B
38 V RAMP OUT
39 V RAMP CAP
40 8.7V REG OUT
3
2
ABC D E F GH
1234
E0VCC
IC199
MEMORY IC
S-24C02BDP-1A
C118
1006.3V KA
C101
0.01 F
AT+5V
41 NC
42 HVCO F/B
43 AFC FILTER
44 DEF GND
45 FBP IN
46 H OUT
47 DEF VCC
48 NC
49 HI VCC
50 R OUT
51 G OUT
52 B OUT
53 ACL
54 NC
55 PROTECT
56 SDA
57 H_CTL
58 SCL
59 NC
60 NC
61 NC
62 DEGAUSS_H
63 STANDBY_H
64 VOLUME
65 NC
66 AFT
67 KEY1
68 KEY2
69 POWER_ON
70 REMOCON
71 AV2
72 AV1
73 AUDIO_MUTE
74 X-RAY
75 IIC_OFF
76 ON_TIMER
77 BBE
78 POWER FAIL
79 NC
80 EXT_MUTE
5.1
0
SWITCHING
4.8
Q105
KRA102MAT
R121
D106_1
POWER ON/ON TIMER
270 1/4W
SLR-342VCT32
R112
2.2K 1/4W
R116
2.2K
OS101
RPM7138-H5
R125
SDA
SCL
AFT
KEY1 V_OUT
R113
KEY2 V_FEEDBACK
2.2K 1/4W
POWER_ON
R115
22K
REMOCON
AUDIO_MUTE
X-RAY
47K
IIC_OFF
ON_TIMER
POWER_FAIL AUDIO_IN
AT+5V
ON_TIMER
REMOCON
R143
47
1025V KA
C123
0
4.9
4.8
123
B+
GND
Vout
0000
E2
E1
MODE
SCL
4.9 0 4.8
R119_1
22K 1/4W
R127
1K
CH UP
SW101
EVQ21505R
VSS
SDA
5678
4.8
4.7K
R105
R106
4.7K
R130
10K 1/4W
R129
47K
MICON/CHROMA IC
IC101
OEC7091A
R128
560
SW102
CH DOWN
EVQ21505R
P.CON+5V
R109
10K 1/4W
R124_1
10K
0000004.80 0.72.32.22.38.004.8 0 4.8 8.0 2.0 1.0 0 3.4 3.7 0
4.8
6566676869
2.4
4.9
4.9
4.9
4.8
70717273747576777879
0
NC
4.9
NC
4.9
2.8
4.8
0
0
NC
4.8
0
4.9
NC
1 101112131415161718
R126
2.7K
SW103
VOL UP
VOL DOWN
EVQ21505R
IIC
TIM
INT
PWM
AD
W809
I/O
NC
SW104
XO
3
KEY2
R101
560
EVQ21505R
C112
ROM
RAM
4
100P CH
C102
0.01 F
KEY1
POWER
MICON/CHROMA/TUNER SCHEMATIC DIAGRAM
(MAIN PCB)
1050V KA
10K 1/4W
CPU core
4716V YK
C103
POWER_ON
SW105
R110
R107
MCU GND
OSD
CCD
VCO
7
C104
R102
EVQ21505R
100
H_CTL
8809
1.0
0.01 F
1K
C105 470P B
R108
C106
R103 1K
C633
R617
47K 1/4W
R618
22K
B.OUT
ABCL
D606
11E1-EIC
100
SDA/SCL
P-ON CONT
CLK CONT
150V KA
C108_1
C107 220P B
IIC BUS
DECODER
0.001 B
R615 100 1/4W
R616 1K 1/4W
PGB OUTPUT Stage
DRIVE
CUT-OFF
HV BLK
Power Manage.
MCU RESET
MCU
CLK
C601
1M
W816
567
150V KA
NC NC NC
W833
R104
G.OUT
R614 100 1/4W
C602
W823
R.OUT
R613 100 1/4W
RGB Proc.2
OSD SW
CONTRAST
BRIGHTNESS
Vldeo Proc.
C-TRAP/YDELAY
SHARPNESS
BLACK STRETCH
Y MUTE
LPF
6bB AMP
VCXO
X601
0.1 F
100CT3R505
C603
C604
AT+5V
R620
W828
C630
10V
470
YK
C629
R609
120K
0.01 F
Hor.Proc.
SYNC SEPA/Hor.VCO
Hor.COUNT DOWN
AFC-1/H COINCIDENT
AFC-2 H PHASE
RGB Proc.1
RGB MATRIX
COLOR CONT
R602
100 1/4W
3.579545MHz
22P CH
C606
0.022 F
150V KA
C605
R601
8.2K
1/4W
5.5
8.8
4.9
5V REG
Q601
KTC3203_Y
2.2K 1/2W
3
R611
R627
192 20 21 22 23 24
10010V YK
H_SYNC
2
10K 1/4W
10K
Ver.Proc.
Ver SYNC SEP
Ver.COUNT DOWN
V RAMP
Chroma Proc.
ACC/C-BPF
APC/KILLER
TINT/DEMO
C609
0.01 F
C610
476.3V KA
120 1/2W
R610
C627
C628
R603
6.8K
150V KA
ATT
H_OUT
C626
0.01 F
41424344454647484955051525354555657585966061626364
NCNC
R621
220 1/4W
0.01 F
40
30 31 32 33 34 35 36 37 38 39
25 26 27 28 29
1.904.92.22.505.52.83.302.74.94.92.70.31.904.94.94.9 000
C615
C616
8.6
4.7
3.6
2.6
0
3.2
3.5
0.7
2.8
8.7
1.9
2.2
5.5
2.2
1.9
NC
NC
NC
NC
0
NC
150V KA
150V KA
R606
22K 1/4W
C624_1
C622
C614
6.0
4
150V KA
1
150V KA
C612
H.CTL
Q607
KTC3198
163V MKT
AUDIO_OUT
100 1/4W
VIDEO_IN
150V KA
TU_VIDEO
TU_AUDIO
5.6
W808
H_CTL
R604
5.0
P.CON+5V
TUNER+5V
P.CON+5V
1SS133
C617
C623
2.250V KA
R607
100 1/4W
D603
5V REG
Q602
KTC3203_Y
10010V YK
5V REG
KTC3203_Y
C620_1
Q603
0.01 B
8.5
5.5
5.5
7.9
11.3
C621
D604
MTZJ8.2B
4716V YK
4.9
7.2
7.2
4.9
8V REG
Q606
KTC3203_Y
R605
220 1/2W
R629
22 3W
TU001
ENG36A01G
R608
1K 1/4W
19
NC
TUNER+5V
SCL
SDA
AFT
TU_AUDIO
P.CON+B
TU_VIDEO
20
18
1
2
NC
3
NC
4
5
NC
6
NC
7
NC
8
NC
9
NC
10
11
12
13
14
NC
15
NC NC
16
17
21
8
FROM/TO DEFLECTION/CRT
CLAMP
P.CON+B
V_OUT
GND
V_FEEDBACK
ABCL
H_OUT
X-RAY
R.OUT
G.OUT
B.OUT
H_SYNC
7
6
FROM/TO TV POWER
UNREG+12V
AT+5V
POWER_FAIL
UNREG+12V
X-RAY
GND
FROM/TO SOUND/AV
AUDIO_MUTE
VIDEO_IN
AUDIO_IN
AUDIO_OUT
P.CON+5V
GND
5
4
NC
0.01 F
NC
NC
NC
NC
TUNER+5V
3.3uH 0305
L001
C001
3
NC
NC
NC
NC
C007
0.022 B
15K 1/2W
C004
0.022 F
D001
R002
MTZJ33B
R003
100
R004
R001
15K 1/2W
100
SCL
SDA
AFT
TU_AUDIO
P.CON+B
TU_VIDEO
IIC_OFF
SDA
SCL
TEST POINT
CP601
00_8283_0611_00_000
NC
NC
IIC_OFF
SDA
SCL
GND
PCB010
TMC558
6
5
4
3
2
2
1
1
NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
ABC D E F GH
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
CAUTION
:SINCE THESE PARTS MARKED BY
CRITICAL FOR SAFETY,USE ONES
DESCRIBED IN PARTS LIST ONLY
ARE
ATTENTION
:LES PIECES REPAREES PAR UN ETANT
DANGEREUSES AN POINT DE VUE SECURITE
N’UTILISER QUE CELLS DECRITES
DANS LA NOMENCLATURE DES PIECES
CAUTION: DIGITAL TRANSISTOR
R.SIGNAL
G.SIGNAL
B.SIGNAL
DEFLECTION SIGNAL
TUNER VIDEO SIGNAL
1
8
G-3
G-4
7
6
DEGAUSS COIL
L503
8R140032
21
ABC D E F GH
TV POWER SCHEMATIC DIAGRAM
4A 125V
CAUTION
ATTENTION
CP502
A1561WV2-2P
1
2
TH501_1
B59203-S1060-B14
:FOR CONTINUED PROTECTION AGAINST FIRE HAZARD,
REPLACE ONLY WITH THE SAME TYPE 4A 125V (F501)
FUSE.
:POUR UNE PROTECTION CONTINUE LES RISQUES
D’INCEIE N’UTILISER QUE DES FUSIBLE DE MEME
TYPE 4A 125V (F501).
W802
003P-2100
CP503
1
R500
2.7M 1/2W
+-10%
D501
1N4005-EIC
D502
R501
5.6 5W
1N4005-EIC
R514
0.22 1W
R510
6.8M 1/4W
R522
6.8M 1/4W
(MAIN PCB)
D505
SB290S
C518
470P500V B
D510
RU2AM-EIC
C517_1
820P2KV R
R517_1
11W
C521
100160V MHE
C519
TO SOUND/AV
GND
SOUND+B
100016V YK
SOUND_GND
FROM/TO DEFLECTION/CRT
+B
UNREG+12V
P.CON+B
GND
R523
47K
PROTECT DRIVE
2SA1624
135.0
10100V MHE
C507
R525
1.2 2W
Q503
135.0
0
R527
5.6K
W834
8
7
6
5
4
3
2
AC120V_60Hz
CD501
0R414903
WIDE
BLADE
BLACK
WHITE
S501AS501B
FH501
EYF-52BC
4A 125V
F501
51MS040L
4A125V
FH502
EYF-52BC
C505
0.22275V ECQUL
R538
1.5M 1/2W
C506
0.001250V KX
C508
0.0047250V KX
34
12
COIL,LINE FILTER
L501
1R5A102F20
C514
0.001500V B
C503
R506
2.7K 1/4W
C501_2
C509
0.047 M
0.0082 B
D503
R520
C510
0.1 F
1N4005-EIC
D508
12K 1/4W
R509
1SS133
220 1/4W
C526_1
220200V YK
D509
MTZJ18B
D512
1SS133
R503
100 1/4W
C511
150V KA
D506
MTZJ18B
C502
0.001500V B
D504
1N4005-EIC
B501
W5RH3.5X5X1.0
W819
POWER AMP
Q501
STP5NC50FP
820P2KV R
144.0
D
S
0.1
W830
R542
4.8
G
KTC3198
0.68 1W
HS501
763WSAA013
BUFFER
Q502
R508
220 1W
4.8
0.1
0
1.7
NC
144.0
NC
10.3
6.6
10.3
FEED BACK
LTV-817M-VB
T502
81291084
8
7
6
5
4
3
2
IC501
11.5
0.1
34
R528
6.8K 1/4W
R516
4.9
10K 1/4W
0
P.FAIL
Q505
4.8
KTA1266
D521
MTZJ6.8B
1SS133
R505
1K 1/4W
R504
10.0
11
0
12
D515
W810
R502
680 1/4W
1SS133
100 1/4W
R512
B504
W5RH3.5X5X1.0
D511
1SS133
D528
R513
2.2K 1/4W
MTZJ5.6B
132.3
13
0
14
0
15
11.3
16
0
NC
17
0
NC
18
10.5
1
9.5
2
1N4937
SB290S
9.5
5.5
D516
D513
100 1/4W
C513_1
6.0
FEED BACK
SWITCHING
Q507
KTC3198
R519
1.2K 1/4W
C515
150V YK
C516
220016V YK
0.001 CH
R515
120K 1/2W
R518
R507
D514
27 1/4W
5.6K +-1%
1SS133
D522
W832
R537
22K 1/4W
FROM/TO MICON/CHROMA/TUNER
POWER_FAIL
X-RAY
UNREG+12V
AT+5V
GND
PCB010
TMC558
5
4
3
2
1
NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
CAUTION
:SINCE THESE PARTS MARKED BY
CRITICAL FOR SAFETY,USE ONES
DESCRIBED IN PARTS LIST ONLY
ARE
ATTENTION
:LES PIECES REPAREES PAR UN ETANT
DANGEREUSES AN POINT DE VUE SECURITE
N’UTILISER QUE CELLS DECRITES
DANS LA NOMENCLATURE DES PIECES
1
ABC D E F GH
ABC D E F GH
G-6
G-5
(CRT PCB)
FROM MICON/CHROMA/TUNER
CLAMP
8
G.OUT
R.OUT
B.OUT
7
6
FROM/TO MICON//CHROMA/TUNER
5
X-RAY
P.CON+B
W831
CP802A B2013H02-5P
GND GND
CLAMP CLAMP
G.OUT G.OUT
R.OUT R.OUT
B.OUT B.OUT
CP803A B2013H02-4P
HEATER HEATER
HEATER HEATER
GND GND
NC NC
180V 180V
1
GND GND
2
CLAMP CLAMP
3
G.OUT G.OUT
4
R.OUT R.OUT
5
B.OUT B.OUT
1
2
GND GND
NC NC
3
180V 180V
4
TO DY
5
A1561WV2-A5P
4
3
2
NC
1
CD802
1
2
3
4
5
CD803
1
2
3
4
CD801_1
V801
A34AGT13X98(L)
9
10
R
8
G
6
B
11
CP401
CP802B B2013H02-5P
CP803B B2013H02-4P
CP801
TBS-X01X-A1
1
175
8
RED OUT
Q801
1
L801
220uH
100.6
2SC1473A
3.2
2.7
C808
330P B
R809
R813
4.7K 1/4W
98.4
330 1/4W
GREEN OUT
Q802
2SC1473A
3.2
2.7
C809
BLUE OUT
R811
R815
330P B
4.7K 1/4W
95.4
330 1/4W
Q803
2SC1473A
3.2
2.7
C810
R814
4.7K 1/4W
7
R816
330 1/4W
330P B
6
161514
TP024TP022
1/4W
R802 2.7K
R803_1 15K 1W
R804 2.7K 1/4W
R805_1 15K 1W
R807_1 15K 1W
TP023
1/4W
R806 2.7K
5
MKT
4.7
R410
R413
R429
1W
(MAIN PCB)
13
330 1/2W
R415
1.8K 1/2W
1/2W
2.2K
C427
1050V YK
DEFLECTION/CRT SCHEMATIC DIAGRAM
IC401 AN5522V-OUT IC
THERMAL
10035V
C434
PROTECTION
AMP
025.0
YK
12
D403
11E1-EIC
0.15
YK
470
25V
D411
AU02A-EIC
R422
C422
R416
2.2 1/2W
100V
1 1/2W
22100V YK
R417
10K 1/4W
R418
22K 1/4W
R419
R420
2.7K
470
C417
C418
4725V YK
PUMP
UP
1234567
3.5 2.0 12.0 25.0 3.5
C414
8
R423
100 1/4W
D412
MTZJ5.1B
R424
470 1/4W
R408
10K +-1%
27K +-1%
R401
HS401
763WSAA013
R409
27K +-1%
V_FEEDBACK
4
FROM/TO TV POWER
3
UNREG+12V
2
1
TMC558
GND
V_OUT
ABCL
H_OUT
H_SYNC
GND
P.CON+B
PCB010
T401
1/2W
470
MMTS
0.01100V
ETH09K14BZ
34
2
NC
1
2250V YK
C446
D409
6
10
C410_1
11E1-EIC
0.001 CH
R427
100 1/4W
130.0
0
HS402
763WSAA017
R449
560 1/2W
R448
560 1/2W
0
11
H.OUTPUT
Q401
TT2140LS-YBC11
D404
MTZJ6.2B
C437
R403
10K 1/4W
C406
220P500V B
C443
PMS
0.47250V
MPP
0.00861.25KV
D405
C403
9
1K 1/4W
R446
27.0
0.3
0
C440
TP401
H.DRIVE
Q402
2SC1627_Y
R405
+B
R447
150 2W
D406
11E1-EIC
C401
L401
R404
AU02A-EIC
C420
820P2KV R
YK
47035V
2.2250V MHE
4.7mH
68 1/2W
D410
C448_1
AU02A-EIC
22
250V YK
130.0
132.5
132.5
48.0
25.0
1
6
2
9
7.0
10
0
8
NC
4
3
180K
FB401 FNI-14B002
COL
VIDEO
B+
AFC
HEA
TER
GND
E12
E25
R445
1/4W
C435
ABL
GND
GND
E8
HV
11
F
S
7
8
5
0.1100V
0
4.3
0
NC
MHE
R421
220K 1/4W
D408
11E1-EIC
FOCUS
CP806
FOCUS
SCREEN
ATTENTION
CAUTION
NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
SCREEN
C819
0.0012KV B
PCB110
TCC417
:LES PIECES REPAREES PAR UN ETANT
DANGEREUSES AN POINT DE VUE SECURITE
N’UTILISER QUE CELLS DECRITES
DANS LA NOMENCLATURE DES PIECES
:SINCE THESE PARTS MARKED BY
CRITICAL FOR SAFETY,USE ONES
DESCRIBED IN PARTS LIST ONLY
101.6
ARE
4
96.4
9
8
7
6
0
5
F
1
4
6.4
00
3
99.6
J801
ISMS01S
3
R.SIGNAL
G.SIGNAL
B.SIGNAL
2
DEFLECTION SIGNAL
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
THE RESISTOR MARKED F IS FUSE RESISTOR.NOTE:
THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP
IS NON POLAR ONE.
1
ABC D E F GH
ABC D E F GH
G-7
G-8
SOUND/AV SCHEMATIC DIAGRAM
8
TO MICON/CHROMA/TUNER
19
7
AUDIO_IN
VIDEO_IN
GND
AUDIO 2
VIDEO 2
W811
20
R701
68 1/4W
R702
R703
820
R704
10
47K
RCA JACK WHITE
J703
AV1-09D-4
H
1
2
H
1
2
RCA JACK YELLOW
J702
AV1-09D-3
E
E
(FRONT)
A_IN
V_IN
(MAIN PCB)
TM101
RC-EH040
ACCESSORY
UM-4
BT001
R03(AB)E_2P_G
UM-4
BT002
R03(AB)E_2P_G
8
7
6
EAR PHONE JACK
5
R1007
10 1/2W
4716V KA
C1008
4
FROM TV POWER
SOUND_GND
SOUND+B
GND
3
FROM MICON/CHROMA/TUNER
AUDIO_MUTE
R1001
47K 1/4W
18
5678
08.2 3.5 3.4
-+
1234
0
3.95.1 0.3
SOUND AMP IC
IC1001 AN7511
W813
J1001
MSJ-035-12A_PC
2
3
1
CD101A
CH012002
CD101B
CH012003
SPEAKER
11
22
SP1001
S08F21
8 OHM
6
5
4
3
P.CON+5V
2
AUDIO_OUT
1
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
W803
NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
R1003
68K
R1004
C1001
100K
0.150V KA
R1005
270K
C1003
150V KA
C1004_2
0.0015 B
68K
17
R1008
C1005
1025V KA
PCB010
TMC558
TUNER VIDEO SIGNAL
2
1
AUDIO SIGNAL
ABC D E F GH
MICON/CHROMA/TUNER
WAVEFORMS
1
0.5V 2ms/div
20V 20µs/div
2
200mV 20µs/div
3
1V 20µs/div
5
1V 20µs/div
6
1V 20µs/div7
20V 20µs/div
9
2V 20µs/div
10
200V 20µs/div
11
0.5V 5ms/div
4
DEFLECTION/CRT
0.5V 5ms/div
8
NOTE:
The following waveforms were measured at the point of the
corresponding balloon number in the schematic diagram.
H-1
10V 5ms/div12
13
10V 5ms/div
WAVEFORMS
SOUND/AV
17
0.5V 1ms/div
50V 20µs/div
14
15
50V 20µs/div
16 50V 20µs/div
18
1V 1ms/div
19
200mV 500µs/div
20
500mV 20µs/div
NOTE:
The following waveforms were measured at the point of the
corresponding balloon number in the schematic diagram.
H-2
MECHANICAL EXPLODED VIEW
106
201
201
201
109
PCB110
(CRT PCB ASS'Y)
202
202
103
202
202
102
202
107
101B
101C
207
201
101D
206
105
104
110
108
205
204
203
110
110
PCB010
(MAIN PCB ASS'Y)
101A
101
I-1
MECHANICAL REPLACEMENT PARTS LIST
Location No. TSB P/N Reference No. Description
101 AE000086 A3M120G720 CABINET,FRONT ASSY
101A AE000087 701WPJC186 CABINET,FRONT
101B AD302172 713WPAA052 GLASS,LED
101C AD302173 713WPAA053 GUIDE,REMOCON
101D AE000088 735WPBA668 BUTTON,FRAME
102 AE000537 A3M120G740 CABINET,BACK ASSY
103 AE000090 722549A183 SHEET,RATING
104 AD300132 7230006818 SHEET,CAUTION
105 AD302177 735WPAA505 SPEAKER HOLDER
106 BZ710009 741WUA0019 SPRING,EARTH
107 BZ710260 899HV3T000 HOLDER,ANODE WIRE
108 AE000091 722000A023 SHEET,HWC
109 AE000006 7220001119 SHEET,CSA WARNING
110 AE000535 800WQ0A024 FELT SHEET
201 BZ710275 8121J50B54 SCREW,TAP TITE(P) GW20 5x28
202 BZ710035 8117540A64 SCREW,TAPPING(B0) TRUSS 4x16
203 BZ710018 8107630804 SCREW,TAP TITE(S) BRAZIER 3x8
204 BZ710352 8109I30604 SCREW,TAP TITE(B) WH7 3x6
205 BZ710562 8109I30804 SCREW,TAP TITE(B) WH7 3x8
206 BZ710031 8110630A04 SCREW,TAP TITE(P) BRAZIER 3x10
207 BZ710030 8110630804 SCREW,TAP TITE(P) BRAZIER 3x8
--- AE000092 723000C202 SHEET,BAR CODE
--- AE000093 791WHA0090 LAMIFILM,BAG
--- AD300809 792WHAA052 PACKAGE,TOP
--- AD300810 792WHAA053 PACKAGE,BOTTOM
--- AE000094 793WCDB717 GIFT BOX
--- AD302179 A3M105A975 INSTRUCTION BOOK KIT
--- AD300022 J3I70417 REGISTRATION CARD
--- AD300023 J3I70436 ESP CARD
--- AD302180 J3M10501A INSTRUCTION BOOK
--- AE000060 JB5UD300 POLYBAG,INSTRUCTION(RED CAUTION)
J1-1
ELECTRICAL REPLACEMENT PARTS LIST
Location No. TSB P/N Reference No. Description
RESISTORS
! R401 BZ210089 R4X5T6273F R,METAL 27K OHM 1/6W
! R408 BZ210092 R4X5T6103F R,METAL 10K OHM 1/6W
! R409 BZ210089 R4X5T6273F R,METAL 27K OHM 1/6W
! R429 AD301700 R635814R7J R,FUSE 4.7 OHM 1W
R447 BZ210229 R3X28A151J R,METAL OXIDE 150 OHM 2W
! R500 BZ210080 R0G3K2275K RC 2.7M OHM 1/2W
! R501 AD300782 R5Y2CD5R6J R,CEMENT 5.6 OHM 5W
! R508 AD300783 R3X181221J R,METAL OXIDE 220 OHM 1W
! R509 BZ210135 R002T4221J RC 220 OHM 1/4W
! R514 BZ210190 R63581R22J R,FUSE 0.22 OHM 1W
! R515 BZ210081 R002T2124J RC 120K OHM 1/2W
! R517 BZ210039 R3X181010J R,METAL OXIDE 1 OHM 1W
! R518 AD300036 R4X5T6562F R,METAL 5.6K OHM 1/6W
! R519 BZ210124 R002T4122J RC 1.2K OHM 1/4W
R525 AD301315 R3X18A1R2J R,METAL OXIDE 1.2 OHM 2W
! R542 BZ210058 R3X181R68J R,METAL OXIDE 0.68 OHM 1W
R629 AE000081 R3X28B220J R,METAL 22 OHM 3W
! R803 BZ210099 R3X181153J R,METAL OXIDE 15K OHM 1W
! R805 BZ210099 R3X181153J R,METAL OXIDE 15K OHM 1W
! R807 BZ210099 R3X181153J R,METAL OXIDE 15K OHM 1W
CAPACITORS
! C403 BZ110149 E02LT4471M CE 470 UF 35V
! C414 AD301434 E02LU4101M CE 100 UF 35V
! C418 BZ110041 E02LT3471M CE 470 UF 25V
C420 BZ110203 C0PLRR7W2K CC 820 PF 2KV R
C437 BZ210173 P4J7F3474J CMPP 0.47 UF 250V PMS
! C443 BZ110258 P4N8FJ862H CMPP 0.0086UF 1.25KV
! C446 BZ110205 E02LU5220M CE 22 UF 50V
! C448 BZ110204 E0ELFD220M CE 22 UF 250V
! C503 BZ110061 C0JTB0513K CC 0.001 UF 500V B
! C505 BZ110025 P2122B224M CMP 0.22 UF 275V ECQUL
C506 AD301026 CD39E0M13M CC 0.001 UF 250V
C508 AD301391 CD39E0MQ3M CC 0.0047UF 250V
C514 BZ110203 C0PLRR7W2K CC 820 PF 2KV R
! C515 BZ110135 E02L02222M CE 2200 UF 16V
C517 BZ110203 C0PLRR7W2K CC 820 PF 2KV R
! C519 AD300925 E02LT2102M CE 1000 UF 16V
C521 BZ110092 E5EZFB101M CE 100 UF 160V
! C526 BZ110089 E02LFC221M CE 220 UF 200V
C819 AD300078 C0JBB0713K CC 0.001 UF 2KV B
DIODES
D001 BZ410037 D97U03301B DIODE,ZENER MTZJ33B T-77
D106 BZ410054 0021721150 LED SLR-342VCT32
D403 BZ410043 D2WT011E10 DIODE,SILICON 11E1-EIC
D404 BZ410066 D97U06R21B DIODE,ZENER MTZJ6.2B T-77
! D405 BZ410063 D2WTAU02A0 DIODE,SILICON AU02A-EIC
D406 BZ410043 D2WT011E10 DIODE,SILICON 11E1-EIC
D408 BZ410043 D2WT011E10 DIODE,SILICON 11E1-EIC
D409 BZ410043 D2WT011E10 DIODE,SILICON 11E1-EIC
! D410 BZ410063 D2WTAU02A0 DIODE,SILICON AU02A-EIC
D411 BZ410063 D2WTAU02A0 DIODE,SILICON AU02A-EIC
! D412 BZ410020 D97U05R11B DIODE,ZENER MTZJ5.1B T-77
D501 BZ410085 D2WXN40050 DIODE,SILICON 1N4005-EIC
! D502 BZ410085 D2WXN40050 DIODE,SILICON 1N4005-EIC
! D503 BZ410085 D2WXN40050 DIODE,SILICON 1N4005-EIC
D504 BZ410085 D2WXN40050 DIODE,SILICON 1N4005-EIC
! D505 BZ410076 D2WXB290S0 DIODE,SILICON SB290S
D506 AD300671 D97U01801B DIODE,ZENER MTZJ18B T-77
D508 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77
! D509 AD300671 D97U01801B DIODE,ZENER MTZJ18B T-77
! D510 BZ410080 D2WXRU2AM0 DIODE,SILICON RU2AM-EIC
D511 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77
! D512 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77
D513 BZ410076 D2WXB290S0 DIODE,SILICON SB290S
D514 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77
D515 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77
! D516 AD300731 D2WXN49370 DIODE,SILICON 1N4937
D521 BZ410022 D97U06R81B DIODE,ZENER MTZJ6.8B T-77
D522 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77
D528 BZ410021 D97U05R61B DIODE,ZENER MTZJ5.6B T-77
D603 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77
J2-1
ELECTRICAL REPLACEMENT PARTS LIST
Location No. TSB P/N Reference No. Description
DIODES
D604 BZ410058 D97U08R21B DIODE,ZENER MTZJ8.2B T-77
D606 BZ410043 D2WT011E10 DIODE,SILICON 11E1-EIC
ICS
IC101 AD302159 I56F07091A IC OEC7091A
IC199 AD302160 A3M105A015 IC (FOR USA) S-24C02BDP-1A
IC199 AE000082 A3M106A015 IC (FOR CANADA) S-24C02BDP-1A
! IC401 BZ611053 I01TD55220 IC AN5522
IC501 BZ410088 0002E00610 PHOTO COUPLER LTV-817M-VB
IC1001 BZ611001 I01DP75110 IC AN7511
TRANSISTORS
Q105 BZ510086 TPATB03003 COMPOUND TRANSISTOR KRA102MAT
! Q401 AD301779 TD3Q021400 TRANSISTOR,SILICON TT2140LS-YBC11
! Q402 BZ510089 TC5T01627Y TRANSISTOR,SILICON 2SC1627_Y(TPE2)
! Q501 BZ510093 TJXG5NC500 FET STP5NC50FP
! Q502 BZ510069 TCATC31980 TRANSISTOR,SILICON KTC3198-AT(Y,GR)
Q503 BZ510004 TA3T016240 TRANSISTOR,SILICON 2SA1624-AA
Q505 BZ510073 TAATA12660 TRANSISTOR,SILICON KTA1266-AT(Y,GR)
Q507 BZ510069 TCATC31980 TRANSISTOR,SILICON KTC3198-AT(Y,GR)
Q601 BZ510070 TCAT032034 TRANSISTOR,SILICON KTC3203_Y-AT
Q602 BZ510070 TCAT032034 TRANSISTOR,SILICON KTC3203_Y-AT
Q603 BZ510070 TCAT032034 TRANSISTOR,SILICON KTC3203_Y-AT
Q606 BZ510070 TCAT032034 TRANSISTOR,SILICON KTC3203_Y-AT
Q607 BZ510069 TCATC31980 TRANSISTOR,SILICON KTC3198-AT(Y,GR)
! Q801 AD300794 TCKT1473A0 TRANSISTOR,SILICON 2SC1473A-TA-(RQ)
! Q802 AD300794 TCKT1473A0 TRANSISTOR,SILICON 2SC1473A-TA-(RQ)
! Q803 AD300794 TCKT1473A0 TRANSISTOR,SILICON 2SC1473A-TA-(RQ)
COILS &TRANSFORMERS
L001 AE000290 02167F3R3J COIL 3.3 UH
L401 AD301644 021L75472J COIL 4.7 MH
! L501 AD300677 029T00A7M1 COIL,LINE FILTER 1R5A102F20
! L503 AD302161 028R140032 COIL,DEGAUSS 8R140032
L801 BZ310113 021673221K COIL 220 UH
T401 BZ310157 045009003J TRANS,HORIZONTAL DRIVE ETH09K14BZ
! T502 AD302162 0481291084 TRANSFORMER,SWITCHING 81291084
JACKS
J702 AD300680 060Q401077 RCA JACK AV1-09D-3
J703 AD300681 060Q401076 RCA JACK AV1-09D-4
! J801 AD301147 066F120018 SOCKET,CATHODE RAY TUBE ISMS01S
J1001 AD302163 060J121014 JACK,RCA,3.5 MSJ-035-12A_PC
SWITCHES
SW101 BZ612010 0504101T34 SWITCH,TACT EVQ21505R
SW102 BZ612010 0504101T34 SWITCH,TACT EVQ21505R
SW103 BZ612010 0504101T34 SWITCH,TACT EVQ21505R
SW104 BZ612010 0504101T34 SWITCH,TACT EVQ21505R
SW105 BZ612010 0504101T34 SWITCH,TACT EVQ21505R
P.C.BOARD ASSEMBLIES
PCB010 AE000083 A3M120G010 PCB ASS'Y (FOR USA) TMC558A
PCB010 AE000219 A3M121G010 PCB ASS'Y (FOR CANADA) TMC558A
PCB110 AE000084 A3M120G110 PCB ASS'Y TCC417A
MISCELLANEOUS
B501 BZ310121 024HT03553 CORE,BEADS W5RH3.5X5X1.0
B504 BZ310121 024HT03553 CORE,BEADS W5RH3.5X5X1.0
BT001 AE000012 1412004008 BATTERY,MANGAN R03(AB)E_2P_G
BT002 AE000012 1412004008 BATTERY,MANGAN R03(AB)E_2P_G
! CD501 AD300685 120R414903 CORD,AC BUSH 0R414903
! CP401 BZ614303 069S450089 CONNECTOR PCB SIDE A1561WV2-A5P
! CP502 AD300687 069S420110 CONNECTOR PCB SIDE A1561WV2-2P
CP503 BZ614016 069W01001A CONNECTOR PCB SIDE 003P-2100
CP601 AD301329 069E260659 CONNECTOR PCB SIDE 00_8283_0611_00_000
CP801 AD300800 069W010030 CONNECTOR PCB SIDE TBS-X01X-A1
CD101A AD301330 06CH012002 CORD,CONNECTOR CH012002
CD101B AD301331 06CH012003 CORD,CONNECTOR CH012003
CP802A BZ614276 067U005049 WIRE HOLDER B2013H02-5P
CP802B BZ614276 067U005049 WIRE HOLDER B2013H02-5P
CP803A BZ614334 067U004029 WIRE HOLDER B2013H02-4P
CP803B BZ614334 067U004029 WIRE HOLDER B2013H02-4P
EL001 BZ614043 124116281A EYE LET XRY16X28BD
EL002 BZ614044 124120301A EYE LET XRY20X30BD
! F501 AD302166 081PC04005 FUSE 51MS040L
! FB401 AD302167 043214039F TRANSFORMER,FLYBACK FNI-14B002
FH501 BZ614005 06710T0006 HOLDER,FUSE EYF-52BC
J2-2
ELECTRICAL REPLACEMENT PARTS LIST
Location No. TSB P/N Reference No. Description
MISCELLANEOUS
FH502 BZ614005 06710T0006 HOLDER,FUSE EYF-52BC
OS101 AD301048 0773071001 REMOTE RECEIVER RPM7138-H5
S101 AD302168 WBL6026038 FLAT CABLE AWM2468 AWG26 4C BLACK 260MM
S102 BZ614371 WCL6834038 FLAT CABLE AWM2468 AWG26 5C GRAY 340MM
SP1001 AD300689 070Y132018 SPEAKER S08F21
! TH501 AD302000 D8EE0B1400 DEGAUSS ELEMENT B59203-S1060-B14
TM101 AE000085 076N0EH040 TRANSMITTER RC-EH040
TU001 AD302169 0163100002 RF UNIT ENG36A01G
! V801 BZ614141 098Q1404B2 CRT W/DY A34AGT13X98(L)
X601 AD302003 100CT3R505 CRYSTAL HC-49/C
RESISTOR
CAPACITORS
RC................... CARBON RESISTOR
CC................... CERAMIC CAPACITOR
CE................... ALUMI ELECTROLYTIC CAPACITOR
CP................... POLYESTER CAPACITOR
CPP.................. POLYPROPYLENE CAPACITOR
CPL.................. PLASTIC CAPACITOR
CMP................... METAL POLYESTER CAPACITOR
CMPL................ METAL PLASTIC CAPACITOR
CMPP................ METAL POLYPROPYLENE CAPACITOR
J2-3
TOSHIBA CORPORATION
1-1, SHIBAURA 1-CHOME, MINATO-KU, TOKYO 105-8001, JAPAN
Loading...