Page 1
Z597 Z Master® Diesel Mowers
Model No. For Z597 Diesel Mowers
Loose Parts
Use the chart below to verify that all parts have been shipped.
Form No. 3356-227 Rev A
Setup Instructions
Step
1
2
3
4
5
6
7
No parts required
No parts required
Rear wheels
Roll bar, right section
Roll bar, left section
Roll bar, center section
Bolt (3/8 x 1 inch)
Curved washer
Flange nut (3/8 inch)
Bolt (1/2 x 3–1/4 inch)
Flange nut (1/2 inch)
No parts required
No parts required
Number 2 general purpose lithium
base or molybdenum base grease.
(Purchase separately.)
Description
Qty.
–
–
2
1
1
1
8
8
8
2
2
–
–
1 tube Check the machine for grease.
Remove parts from the crate.
Check the tire pressure.
Install the drive wheels.
Install the Rollover Protection
System (ROPS).
Adding diesel to the machine.
Charge the battery.
Use
8
9
10
11
© 2006—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
No parts required
No parts required
No parts required
Operator’s Manual
Parts Catalog
Engine Owner’s Manual
Registration Card
Safety Video
Key 2
Register at www.Toro.com. Original Instructions (EN)
–
–
–
1
1
1
1
1
Check the engine oil level.
Prepare the side discharge chute.
Check the machine before delivery
to the customer.
Delivering the machine to the
customer.
Printed in the USA.
All Rights Reserved
Page 2
Step
Step
1
Removing Parts from the
Crate
No Parts Required
Procedure
R emo v e the tires and the par ts for the R OPS from
the shipping crate .
Step
2
Checking the Tire Pressure
No Parts Required
3
Raising the Machine Up and
Installing the Drive Wheels
Parts needed for this step:
2
Rear wheels
Procedure
1. R emo v e the screws holding the right angle
retaining plate to the crate .
Procedure
Pressure: 13 psi (90 kP a)
Note: T he front caster wheel is a semi-pneumatic
tire and does not need to be c hec k ed.
Chec k the air pressure in the dri v e tires .
Figure 1
Figure 2
2. Raise the bac k of the mac hine up and suppor t
it with jac k-stands .
Figure 3
3. R emo v e the wheel n uts from both sides of the
v ehicle and remo v e the right angle retaining
plate . Discard the screws and retaining plate .
2
Page 3
Figure 4
4. Mount the wheels with the v alv e stem to the
outside and secure them with the wheel n uts
previously remo v ed.
5. T or que the wheel n uts to 95 ft-lb (128 N·m).
Step
4
Installing the Roll Over
Protection System
Parts needed for this step:
1
Roll bar, right section
1
Roll bar, left section
1
Roll bar, center section
8
Bolt (3/8 x 1 inch)
8
Curved washer
8
Flange nut (3/8 inch)
2
Bolt (1/2 x 3–1/4 inch)
2
Flange nut (1/2 inch)
6. R emo v e the jac k-stands .
Figure 5
Procedure
1. Loosely install the right and left roll bar section
to the frame , with 8 bolts (3/8 x 1 inc h), 8
cur v ed w ashers , and 8 flang e n uts (3/8 inc h).
Note: T he cur v e w asher cone m ust be
installed to w ard the bolt head.
Figure 6
2. Install the lanyard clips onto the long bolts
(1/2 x 3-1/4 inc h).
Note: Mak e sure the bent tab points to w ard
the head of the bolt.
3
Page 4
Figure 7
3. Lightly oil the ends of the center roll bar
section.
4. Loosely install the center roll bar section using
2 bolts (1/2 x 3-1/4 inc h) and 2 flang e n uts
(1/2 inc h).
Note: Mak e sure the bolts are installed from
the outside of the roll bar .
Note: Mak e sure the lanyard tab is installed
as sho w and points forw ard.
Figure 9
6. T or que all lo w er fasteners , attac hed to the
mac hine frame , to 30 ft-lb .
7. Tighten the center roll bar bolts (1/2 x 3-1/4
inc h) so it rotates freely with some resistance .
Note: No more than one thread should be
exposed outside the n ut.
Figure 8
5. Raise the roll bar into the upright position and
secure it with the pins and hair pin cotter pins
fastened to the lanyards
Figure 10
8. Tighten the front knobs ag ainst the center roll
bar ends .
4
Page 5
Figure 11
Step
6
Charging the Battery
No Parts Required
Procedure
Charging the batter y pr oduces gasses that
can explode and cause serious injur y .
• K eep cigar ettes, spar ks and flames a w ay
fr om the batter y .
• Mak e sur e the ignition s witch is of f.
• V entilate when charging or using the
batter y in an enclosed space.
Step
5
Adding Fuel to the Machine
No Parts Required
Procedure
Add diesel to the mac hine before star ting it. R efer
to y our Operator’ s Manual. for the cor rect fuel and
procedure .
Important: Do not r un the machine with
the batter y disconnected; electrical dama ge
may occur to the engine.
Charg e the batter y . R efer to the Operator’ s Manual
for instr uctions .
Figure 12
5
Page 6
Step
7
Checking the Machine for
Grease
Parts needed for this step:
1 tube
Procedure
1. R emo v e the belt co v ers on domestic mac hines
Number 2 general purpose lithium base
or molybdenum base grease. (Purchase
separately.)
as sho wn belo w .
Figure 14
3. Chec k the tensioning ar m for g rease .
4. Chec k the g rease for the three spindle bearings .
If needed, add g rease until it comes out of the
lo w er seals .
5. Install the belt co v ers .
Figure 13
2. R emo v e the belt co v ers and bolts on
inter national mac hines as sho wn belo w .
Figure 15
6
Page 7
6. Chec k the g rease for the cooling fan belt idler
ar m.
7. Chec k the g rease for the dri v e belt idler ar ms .
Figure 16
8. Grease the pump belt idler ar m in the front
of the engine .
Step
9
Preparing the Side
Discharge Chute
No Parts Required
Procedure
R emo v e the plastic tie holding the side disc harg e
c hute up and lo w er the c hute into place .
Figure 17
Step
8
Checking the Engine Oil
Level
No Parts Required
Procedure
Before y ou star t the engine and use the mac hine ,
c hec k the oil lev el in the engine crankcase; refer to
Chec king the Oil Lev el in Operator’ s Manual.
7
Page 8
Step
10
Checking the Machine Before Delivery to the Customer
No Parts Required
Procedure
Before deli v ering the mac hine to the customer , ensure that y ou perfor m or ha v e perfor med the
procedures listed in the follo wing table and initial eac h when finished. R efer to the Operator’ s Manual
for instr uctions on perfor ming these procedures .
Initial
Check the tire pressure.
Check the level of the mower.
Check that all mower spindles are greased.
Check the engine oil level.
Check the hydraulic uid level.
Check ROPS is secure.
On liquid cooled machines, check the level of the coolant in the radiator and overow bottle.
Check the adjustment of the parking brake.
Ensure that the machine tracks correctly; refer to the Operator’s Manual for the adjustment
procedure.
Check the safety interlock system; refer to the Operator’s Manual .
Ensure that the PTO works.
Check all fasteners you installed to ensure that they are tight.
Check Procedure
W hen y ou finish setting up the mac hine , sign and date in the space pro vided belo w:
Signature: Date:
8
Page 9
Step
11
Delivering the Machine to the Customer
Parts needed for this step:
1
Operator’s Manual
1
Parts Catalog
1
Engine Owner’s Manual
1
Registration Card
1
Safety Video
2 Key
Procedure
At deli v er y , complete the items listed in the follo wing table and initial eac h when finished.
Model No. Serial No.
9
Page 10
Dealer Initial Customer Initial Check Procedure
Show the customer where the following features are located and how
they function:
Fuel tank caps
Oil ll cap/ Oil dipstick
Engine oil lter
Engine oil drain
Fuel lters
Air lter
Radiator coolant
Hydraulic uid reservoir
Hydraulic lter
Battery
Ignition switch
Throttle lever
Glow plug light and switch
Power take off switch (PTO)
Motion control levers
Parking brake
Mower height-of-cut
Lift assist lever
Z Stand®
Adjustable seat
Hydraulic bypass valves
Rollover Protection System (ROPS)
Mower deck ow bafe
Refer to the Operator’s Manual to point out safety procedures, operation,
and maintenance procedures.
Review the warranty statement as shown in the Operator’s Manual.
Describe the post sale service procedures for your store.
Assist the customer in lling out and mailing the registration card or
register online at www.Toro.com
Make sure that the customer receives the Operator’s Manual, Parts Catalog,
Engine Owner’s Manual, Set Up Instructions, and safety video.
Assist the customer in loading the mower.
Note: W hen y ou, the dealer re presentati v e , ha v e finished deli v ering the mac hine to the customer , sign
and date in the space pro vide belo w and k ee p a copy of this pag e for dealer records .
Signature: Date:
Signature: Date:
10
Page 11
Page 12
Loading...