Page 1
FormNo.3382-315RevA
TITAN
®
RidingMower
ModelNo.Allmodels
SetupInstructions
Setup
LooseParts
Usethechartbelowtoverifythatallpartshavebeenshipped.
ProcedureDescription
Qty.
Use
1
Nopartsrequired
–
Connectthebattery.
Rearhitch1
Bolt(5/16x2-1/2inches)
2
2
Locknut(5/16inch)
2
Installtherearhitch.
3
Nopartsrequired
–
Setupthemotion-controllevers.
4
Nopartsrequired
–
SetuptheRolloverProtectionSystem
(ROPS)bar.
5
Nopartsrequired
–
Checkthemoweradjustment.
Ignitionkey1
Hosecoupling(notincludedwithCE
models)
1
Operator'sManual
1
EngineOperator'sManual
1
6
Operatortrainingmaterial
1
Completethesetup.
Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.
©2013—TheT oro®Company
8111LyndaleAvenueSouth
Bloomington,MN55420
Registeratwww.T oro.com.
OriginalInstructions(EN)
PrintedintheUSA.
AllRightsReserved
*3382-315*A
Page 2
1
ConnectingtheBattery
NoPartsRequired
Procedure
1.Locatethebatteryandnegativebatterycable.
2.Removetheplasticcapfromthenegativebatterypost.
3.Removethefastenersonthenegativebatterycable,
andusethemtosecurethenegativebatterycableto
thenegativebatterypost(
Figure1).
G018395
2
1
4
3
6
5
Figure1
1.Negativebatterycable4.Negativebatterypostcap
2.Wingnut
5.Carriagebolt
3.Washer6.Negativebatterypost
2
InstallingtheRearHitch
Partsneededforthisprocedure:
1Rearhitch
2
Bolt(5/16x2-1/2inches)
2
Locknut(5/16inch)
Procedure
InstallthebrackettotheframeasshowninFigure2and
Figure3.
g015397
1
2
Figure2
Beforeassembly
1.Bolts2.Locknuts
Figure3
Afterassembly
2
Page 3
3
SettinguptheMotion-control
Levers
NoPartsRequired
Procedure
1.Locatethemotion-controlleversattached,butfolded
downonthemachine.
2.Removetheupperbolt(3/8x1inch)andwasher;
loosenthelowerbolt(3/8x1inch).
3.Raisethemotioncontrolleverstotheuprightposition.
4.Aligntheholesinthemotion-controlleverwiththe
holesinthecontrol-armshaft,andinstallthebolt
andwasherremovedpreviously.Repeatthisforboth
controlslevers.
Note:Handtightenallfasteners.
5.Movethemotion-controlleverstotheparkposition,
raisetheseat,andmovethecontrolleversbacktothe
centerposition(neutral).
6.Verifythatthemotion-controlleversareproperly
aligned.
Note:Adjustasnecessary.Tightenallfasteners.
4
SettinguptheRollover
ProtectionSystem(ROPS)Bar
NoPartsRequired
Procedure
1.Removethebolts(1/2x3inches),washers,andnuts
fromthemiddleholeontheROPSplate(Figure4).
Figure4
Leftsideshown;repeatontherightside
1.Washer3.Middlehole
2.Bolt(1/2x3inches)
4.Nut
2.RotatetheROPStotheuprightposition.
3.Installthebolts(1/2x3inches),washers,andnuts
removedpreviouslyintothemiddlehole(Figure4).
4.Removethebolts(1/2x3inches),washers,andnuts
fromthefourthholeintheROPSplate(Figure5).
3
Page 4
Figure5
Leftsideshown;repeatontherightside
1.Washer3.Fourthhole
2.Bolt(1/2x3inches)
4.Nut
5.Installtheremovedbolts(1/2x3inches),washers,and
nutsintothelowestholeintheROPSplate(Figure6).
Figure6
Leftsideshown;repeatontherightside
1.Washer3.Lowesthole
2.Bolt(1/2x3inches)
4.Nut
6.Torqueallofthefastenerstoapproximately45N-m
(400in-lbs).
5
CheckingtheMower
Adjustment
NoPartsRequired
Procedure
Adjusttheside-to-sidelevelandthefront-to-rearbladeslope.
UsetherelevantproceduresintheOperator'sManualtoverify
thatthedeckislevel,andmakeanyadjustmentsasnecessary.
RefertotheOperator'sManualformoreinformation.
6
CompletingtheSetup
Partsneededforthisprocedure:
1Ignitionkey
1
Hosecoupling(notincludedwithCEmodels)
1
Operator'sManual
1
EngineOperator'sManual
1
Operatortrainingmaterial
Procedure
CheckingtheTirePressure
Checkthefrontandreartiresforproperination;referto
CheckingtheTirePressureintheOperator'sManualforthe
recommendedinationpressure.
CheckingtheSide-DischargeChute
Removethepackingrestraintholdingthesidedischargechute
upandlowerthechuteintoplace.
CheckingtheEngine-OilLevel
Beforeyoustarttheengineandusethemachine,checkthe
oillevelintheenginecrankcase;refertoCheckingtheOil
LevelintheOperator'sManual.
Keepallthefollowingitemswiththemachine:
•Ignitionkey
•Hosecoupling(notincludedinCEmodels)
•Operator'sManual
•EngineOperator'sManual
•ViewtheOperatortrainingmaterialbeforeoperatingthe
machine.
4
Loading...