Toro Recycler 20070 Operator's Manual

22in Recycler ®Lawn Mower

Model No. 20070--Serial No. 260000001 and Up

Form No. 3354-915 Rev A

Operator's Manual

Introduction

Read tlfls information carefiflh to learn how to operate and
maintain xour, product properl) and to avoid in}ur) and
product damage. X*%uare responsible for operating the
product properl) and safeh<

X*%umax contact Toro directl) at wwxx:Toro.com for
product and accessor) information, help finding a dealer,

or to register ?our product.
\'(henever xou, need service, genuine Toro parts, or

additional information, contact an Authorized Service
Dealer or Toro Customer Service and have the model and

serial nmnbers of your product read?: Figure 1 identifies the
location of the model and serial numbers on the product.

.3002873

Figure 1

1.

Model and serial number plate

\'('rite the product model and serial numbers in the space
below:

CALIFORNIA

Proposition 65 Warning

The engine exhaust from this product contains

chemicals known to the State of California to cause
cancer, birth defects, or other reproductive harm.

Important: This engine is not equipped with a

spark arrester muffler. It is a violation of California
Public Resource Code Section 4442 to use or operate

the engine on any forest-covered, brush-covered, or
grass-covered land. Other states or federal areas may

have similar laws.

This spark igaition sxstem complies with Canadian
ICES-002

The enclosed Engine Owner's Manual is supplied
for information regarding the US Environmental
Protection Agency (EPA) and the California Emission
Control Regulation of emission systems, maintenance,
and warranty. Replacements may be ordered through
the engine manufacturer.

For models with stated engine horsepower, the gross
horsepower of the engine was laborator? rated b? the engine
manufacturer in accordance with SAt j 1940. As configured
to meet safet3; emission, and operating requirements, the
actual e_gine horsepower on this class of lawn mower will
be significantly lower.

I Model No.

Serial No.

This manual identifies potential hazards and has safety
messages identified b_ the safety" alert swnbol (Figure 2),

wlflch signals a hazard that may cause serious in}ury or
death if _ou do not follow the recommended precautions.

Figure 2

I. Safety alert symbol

This manual uses taro words to lflghlight information.
Important calls attention to special mechaaical information

and Note emphasizes general information worthy of special
attention.

© 2005--The Toro Company
8111 Lyndale Avenue South
Bloomington, MN 55420

®

Safety

This lawn mower meets or exceeds the CPSC blade safet)
requirements for walk-belflnd rotar_ lawn mowers and the
B71.1 specifications of the American National Standards

Institute in effect at the time of production.
Read and understand the contents of this manual

before you start the engine.

The safet_ alert swnbol (Figure 2) is used to alert you to
potential personal in}ur) hazards. Obe) all safety messages
that follow this swnbol to avoid possible in}ur) or death.

Improperl) using or maintaining this mower could resuh in
in}ury or death. To reduce this potential, comply with the
following safety" instructions.

Register at www.Toro.com. Original Instructions (EN)

Printed in the USA.
All Rights Reserved

Tile following instructions have been adapted from the
ANSI/OPEl standard B71.1-2003.

This cutting machine can amputate hands and feet and
throw objects. Failure to observe the following safety

instructions could result in serious injury or death.

General Operation

• Read, understand, and follow aU instructions on tile
machine and in the manual(s) before starting.

• Do not put hands or feet near or under the machine.
Keep clear of the discharge opexfing at all times.

• Only allow responsible adults, who are familiar with the
instructions, to operate tlfis maclfine.

• Clear the area of objects such as rocks, wire, toys, etc.,
which could be thrown bt the blade. Star behind the

handle when the engine is rmming.

• Be sure the area is clear of bystanders before operating.
Stop maclfine if anyone enters the area.

• Do not operate machine barefooted or wlfile wearing
sandals. Always wear substantial footwear.

• Do not pull maclfine backward unless absoluteh
necessar): A1wat s look down and belfind before and
while moving backward.

• Never direct discharged material toward axvone. Avoid
dischargil g material against a wall or obstruction.
Material may ricochet back toward the operator. Stop
the blade when crossing gravel surfaces.

• Do not operate machine without the entire grass
catcher, discharge guard, rear guard, or other safety
protective devices in place and worMng.

• Never leave a runnil g machine unattended.

• Stop the engine and wait until the blade comes to a
complete stop before cleaxfilg the machine, removilg
grass catcher, or unclogging the discharge guard.

• Operate machine only in daylight or good artificial light.

• Do not operate machine wlfile under the influence of
alcohol or drugs.

• Never operate mower in wet grass. Always be sure of
tour roofing; walk; never run.

• Disexgage the drive system, if so equipped, before
starting the engine.

• If the maclfine should start to vibrate abnorma11 B
stop the engine and check for the cause immediate1>
Vibration is general1) a warning of trouble.

• Alwat s wear eye protection when operating machine.

• See manufacturer's instructions for proper operation
and installafion of accessories. Only use accessories

approved bt the manufacturer.

Slope Operation

Slopes are a major factor related to slip and fall accidents,
wlfich can result in severe injur> Operation on all slopes

require extra caution. If you feel uneast on a slope, do
not mow it.

• Mow across the face of slopes; never up and down.
Exercise extreme caution when changing direction on
slopes.

• \'(qtch for holes, ruts, bumps, rocks, or other hidden
objects. Uneven terrain could cause a slip and fall
accident. Tall grass can lfide obstacles.

• Do not mow on wet grass or excessively steep slopes.
Poor footilg could cause a slip and fall accident.

• Do not mow near drop-offs, ditches, or embankments.
"_%ucould lose your foofilg or balance.

Children

Tragic accidents can occur if the operator is not alert to
the presence of clfildren. Children are often attracted to

the maclflne and the mowing acfivitt: Never assume that
clfildren will remain where tou last saw them.

• Keep children out of the mowing area and under the
watchful care of a responsible adult other than the

operator.

• Be alert and turn mower off if a clfild enters the area.

• Never allow children to operate the machine.

• [se extra care when approaching blind corners, shrubs,
trees, or other objects that mat block tour view of a

clfild.

Service

Safe Handling of Gasoline

To avoid personal injury o1"property damage, use
extreme care in handling gasoline. Gasoline is

extremely flammable and the vapors are explosive.

• Extinguish all cigarettes, cigars, pipes, and other sources
of ignition.

• [se onN an approved gasoline container.

• Never remove gas cap or add fuel with the engine
rumfil g. Allow engine to cool before refuelin&

• Never refuel the machine indoors.

• Never store the maclfine or fuel container where there
is an open flame, spark, or pilot light such as on a water

lleater or on other appliances.

• Never fill containers inside a velficle or on a truck or
trailer bed with a plastic liner. Always place containers

on the ground awat from tour velflcle before fillilg.

• Remove gas-powered equipment from the truck or
trailer and refuel it on the ground. If tiffs is not possible,

thenrefl_elsuchequipmentwithaportablecontainer,
ratherthanfromagasolinedispensernozzle.

Keeptilenozzlein contactwithtilerimof tilefuel
tankorcontaineropeningatalltimesuntilfuelingis

complete.Donotuseanozzlelock-opendevice.
If fuelis spilledonclothing,changeclothing

immediate1>

Never overfill fuel tank. Replace gas cap and tighten
secureh:

Safety and Instructional Decals

Important: Safety and instruction decals are located

near areas of potential danger. Replace damaged
decals.

Exhaust contains carbon monoxide, an odorless,
deadly poison that can kill you.

Do not run the engine indoors or in an enclosed area.

General Service

• Never operate maclflne in a closed area.

• Keep all nuts and bolts tight to be sure tile equipment is
in safe worMng condition.

• Never tamper with safety devices. Check their proper
operation regularl?:

• Keep maclline free of grass, leaves, or other debris
build-up. Clean up oil or fuel spillage and remove

am fuel-soaked debris. A11ow machine to cool before
storing.

• If you strike a foreign ob}ect, stop and inspect the
machine. Repair, if necessar 5 before startin&

• Never make a_V ad}ustments or repairs with tile engine
framing. Disconnect the spark plug wire and ground

against engine to prevent mlintended starting.

104-7402

• Check grass catcher components and tile discharge
guard frequently and replace with manufacturer's
recommended parts, when necessary:

• Mower blades are sharp. Wrap tile blade or wear gloves,
and use extra caution when servicing them.

• Do not change tile engine governor setting or overspeed
the engine.

• Maintain or replace safet_ and instruction labels, as
necessary:

104-7403

ID

104-7953

1. Warning--read the Operator's Manual for information on charging the battery; contains lead; do not discard.

2. Read the Operator's Manual.

105-1295

ENTIRE CATCHER iN P_CE :::::::::::::

DANGER

KEEP HANDS and FEET AWAY

0

J

105-6838

108-4791

Setup

Important: Remove and discard the protective

plastic sheet that covers the engine.

1. Unfolding the Handle

Folding or unfolding the handle improperly can
damage the cables, causing an unsafe operating

condition.

• Do not damage the cables when folding or
unfolding the handle.

• If a cable is damaged, contact an Authorized
Service Dealer.

1. Careflflh move tile upper handle forward until tile
handle halves are in line and nest together as shown
in Figure 3.

G002874

Figure 3

2. Tighten the handle knobs (Figure 4).

Figure 5

2. Filling the Engine with Oil

_X%urmower does not come with oil in the engine, but it
does come with a bottle of oil.

1. Remove the dipstick (Figure 6).

G002876

Figure 6

2. Slowly pour oil into the oil fill tube until the oil level
reaches the Full line on the dipstick (Figure 6). Do not
overfill. (Max. fill: 20 oz., Vpe: SAE 30W detergent

oil with an API service classification of SF, SG, SH, SJ,
SL, or lflgher.)

3. Install the dipstick secure1>

Important: Change the engine oil after the first 2

operating hours; change it yearly thereafter. Refer
to Changing the Engine Oil.

Figure 4

3. Rotate the handle rearward (Figure 5) until it clicks into
place.

3. Installing the Fuse

_X_t]r mower comes with a 40-amp fuse that protects the
electric starter.

Product Overview

4

Important: You cannot start the mower with the

electric starter or charge the battery unless you install
the fuse.

1. Unclip both ends of tile batterx cover and remove it
(Figure 7).

G002877

Figure 7

2. Install tlle fuse in tlle fuse holder (Figure 8).

G002878

Figure 8

Note: _ur mower comes with a fuse in the _our

owner's packet and another fuse in tile batter_ box.
Install tile batter_ cover.

1

\

10 G002879 9

Figure 9

1. Cutting height lever 6. Fuel tank cap

2. Oil fill/Dipstick 7. Battery

3. Recoil start handle 8. Air filter

4. Blade control bar 9. Primer

5. Ignition key 10. Spark plug

8

1 2

5

4. Charging the Battery

Refer to Charging the Batter_ in the Maintenance section.

G002880

Figure 10

1. Grass bag 3. Battery charger

2. Side discharge chute 4. Rear discharge plug (installed)

Operation

Filling the Fuel Tank

Gasoline is extremely flammable and explosive. A
fire or explosion from gasoline can burn you and

others.

Checking the Engine Oil Level

1. Remove tile dipstick, wipe it clean, and fifth install tile
dipsdck (Figure 12).

• To prevent a static charge fi'om igniting the
gasoline, place the container and/or mower
directly on the ground before filling, not in a
vehicle or on an object.

• Fill the tank outdoors when the engine is cold.
Wipe up spills.

• Do not handle gasoline when smoking or around
an open flame or sparks.

• Store gasoline in an approved fuel container, out
of the reach of children.

Fill tile fl_el tank with fresh unleaded regular gasoline from
a major name-brand service station (Figure 11).

Important: To reduce starting problems, add fuel

stabilizer to the fuel all season, mixing it with gasoline
less than 30 days old.

1/2 in. (1 cm)_

G002876

Figure 12

2. Remove the dipstick and check the oil level (Figure 12).
If tlle oil level is below the Add mark on the dipstick,
slowly pour oil into the oil fill tube to raise the oil level
to the Full mark on the dipstick. Do not overfill. (Max.
Jill: 20 oz., t3pe: SAE 30W detergent oil witll an API
service classification of SF, SG, SH, SJ, SL, or lflgher.)

3. Install the dipstick secure1>

Figure 1 1

G002881

Adjusting the Cutting Height

Stop the engine and wait for all moving parts to stop.

Do not put your fingers under the housing when adjusting the cutting height.

If the engine has been running, the muffler will be hot and can severely burn you. Keep away fi'om the hot
muffler.

Adiust tile cutting height as desired. Set all four wheels to tile same height.

Note: Onh a front cutting height lever is shown.

2in 3-1/2in

1-5/8in

2_3/8in 3.7/8iq 4"1/41n

Figure 13

Adjusting the Handle Height

Squeeze tile bottom of tile handle halves together and
change the handle holes in wifich the pins are motmted,

as shown in Figure i4.

FRONT ml_ --_

G002882

Starting the Engine

1. Firml? push in tile primer 3 thnes with xour tlmmb,
holding tile primer in for a second before releasing it
each time (Figure 15).

3X

G002581

Figure 15

Note: If tile air temperature is below 55°F (13°C),

firml? push tile primer in 5 times.

2.

Hold tile blade control bar (Figure 16) against tile
handle.

Figure 14

1. Pin

Use this hole to raise the
handle

3. Use this hole to lower the
handle

Figure 16

1. Blade control bar

Start tile engine using either the igxfition key or the
recoil starter (Figure 17).

Stopping the Engine

To stop tile engine, release tile blade control bar (Figure 19).
Remove the ignition ke) when you leave the mower.

Important: When you release the blade control
bar, both the engine and blade should stop within 3
seconds. If they do not stop properly, stop using your

mower immediately and contact an Authorized Service
Dealer.

_002886

Figure 19

Recycling the Clippings

Figure 17

4.

If the mower does not start in 1 or 2 pulls (or within
5 seconds using the electric starter), press the primer
button 1 or 2 times and tr) starting it again.

Note: If tile mower still does not start, contact an

Authorized Service Dealer.

Using the Self-propel Drive

(To operate tile self-propel drive, simply walk with xour
hands on tile upper handle and _our, elbows at your, sides,
and tile mower will automaticalh keep pace with xou

(Figure i8).

G002885

Figure 18

_X_urmower comes from tile factory readx to recycle tile
grass and leaf clippings back into tile lawn.

If tile grass bag is on tile mower, remove it (refer to
Removing tile Grass Bag) before rec3 cling tile clippilgs. If
tile side discharge chute is on tile mower, remove it and
lock tile side discharge door (refer to Removixg tile Side
Discllarge Clmte) before recycling the clippilgs.

Important: Ensure that the rear discharge plug is in
place before you recycle the clippings (Figure 20).

G002586

Figure 20

Bagging the Clippings

Use tile grass bag when 3ou want to collect grass and leaf
clippings from the lawn.

A worn grass bag could allow small stones and

other similar debris to be thrown in the operator's or
bystander's direction and result in serious personal
injury or death to the operator or bystanders.

Check the grass bag frequently. If it is damaged,
install a new Toro replacement bag.

If the side discharge chute is on the mower, remove it and
lock tile side discharge door (refer to Removing tile Side
Discharge Chute) before bagging the clippings.

The blade is sharp; contacting the blade can result
in serious personal injury.

Stop the engine and wait for all moving parts to stop
before leaving the operating position.

Side-discharging the Clippings

[se tlle side discharge for cutting ver_ tall grass.

If tlle bag is on tlle mower, remove it and insert tlle rear
discharge plug (refer to Removing tlle Grass Bag) before

side-discharging tile clippings.

Important: Ensure that the rear discharge plug is in

place before you side-discharge the clippings (Figure

24).

Installing the Grass Bag

i. Raise and hold up tile rear door (Figure 2i).

3002887

Figure 21

2. Remove tile rear discharge plug (Figure 22).

G002588 "_"_

Figure 22

3. Install the bag onto the door rod (Figure 23).

The blade is sharp; contacting the blade can result

in serious personal injury.

Stop the engine and wait for all moving parts to stop
before leaving the operating position.

G002586

Figure 24

Installing the Side Discharge Chute

i. [ nlock tile side discharge door (Figure 25).

Figure 23

4.

Lower tile rear door.

Removing the Grass Bag

To remove tile bag, reverse tile steps above.

G002590

Figure 25

2. Lift open tile side discharge door (Figure 26).

b

_'8

Figure 26

3. Install the side discharge chute and close the door onto
tlle chute (Figure 27).

10

Wet grass or leaves can cause serious injury if
you slip and contact the blade. Mow only in dry

conditions.

G002592

Figure 27

Removing the Side Discharge Chute

To remove tile side discharge chute, reverse the steps above.

Important: Lock the side discharge door after you

close it (Figure 28).

G002593

Figure 28

Operating Tips

General Mowing Tips

• Clear tile area of sticks, stones, wire, branches, and
other debris that tile blade could hit.

• Avoid striMng solid objects with tile blade. Never
deliberately mow over an? object.

• If tile mower strikes an object or starts to vibrate,
immediately stop tile engine, disconnect the wire from
the spark plug, and examine the mower for damage.

Alternate the mowing direction. Tiffs helps disperse the
clippilgs over the lawn for even fertilization.

If the fi_fished lawn appearance is unsatisfactor); tr) one
or more of the followilg:

- Replace the blade or have it sharpened.

- Walk at a slower pace wlfile mowilg.

- Raise the cuttil g height on your mower.

- Cut the grass more frequend):

- Overlap cuttil g swaths instead of cuttil g a full
swath with each pass.

- Set the cutting height on the front wheels one
notch lower than the rear wheels. For example, set
the front wheels at 2 inches (51 ram) and the rear
wheels at 2-3/8 inches (60 ram).

Cutting Leaves

• After cutting the lawn, ensure that half of the lawn
shows through the cut leaf cover, x*%uma_ need to

make more than one pass over the leaves.

• If there are more than 5 inches (13 cm) of leaves on the
lawn, set the front cutting height one or two notches
higher than the rear cutting height.

• Slow down your mowing speed if the mower does not
cut the leaves find? enough.

• For best performance, install a new blade before the
cutting season begins.

• Replace the blade when necessar_ with a Toro
replacement blade.

Cutting Grass

• Cut onh about a third of the grass blade at a time. Do
not cut below the 2-inch (51 ram) setting unless the
grass is sparse or it is late fall when grass growdl begins

to slow down. Refer to Adjusting the Cutting Height.

• When cuttilg grass over 6 inches (15 cm) tall, mow
at the highest cutting height setting and walk slower;
then mow again at a lower setting for the best lawn
appearance. If the grass is too long, the mower ma_

plug and cause the engine to sta11.

• Mow only dr) grass or leaves. \Vet grass and leaves tend
to clmnp on the yard and can cause the mower to plug

or the engine to sta11.

11

Maintenance

Note: Determine the left and right sides of the machine from the normal operating position.

Recommended Maintenance Schedule(s)

Maintenance Service

Interval

After the first 2 operating

hours

Maintenance Procedure

• Change the engine oil.

Check the engine oil level.

Before each use or daily

Ensure that the engine stops within 3 seconds after releasing the blade control
bar.

Clean grass clippings and dirt from under the mower.

Every 25 hours •

Before storage •

Charge the battery.
Empty the fuel tank before repairs as directed and before annual storage.

Replace the air filter (more frequently in dusty operating conditions).
Change the engine oil.

Yearly •

Lubricate the wheel gears.
Replace the blade or have it sharpened (more frequently if the edge dulls quickly).
Refer to your Engine Operator's Manual for any additional yearly maintenance
procedures.

Important: Refer to your Engine Operator's Manual for additional maintenance procedures.

Preparing for Maintenance

1.

Stop the engine and wait for all moving parts to stop.

2.

Disconnect the spark plug wire from the spark plug
and hook it onto the retaining post (Figure 29) before
performing an) maintenance procedure.

Tipping the mower may cause the fuel to leak.
Gasoline is flammable, explosive and can cause

personal injury.

Run the engine dry or remove the gasoline with a
hand pump; never siphon.

1

G002594

Figure 29

1. Spark plug retaining post

After performing the maintenance procedure(s),
connect the spark plug wire to the spark plug.

Important: Before tipping the mower to change

the oil or replace the blade, allow the fuel tank to
run dry through normal usage. If you must tip the
mower prior to running out of fuel, use a hand fuel
pump to remove the fuel. Always tip the mower
onto its side, with the air filter up.

Replacing the Air Filter

Replace the air filter yearl) ; replace it more frequently in
dust)." operating conditions.

1. Refer to Preparing for Maintenance.

2. Rotate the air filter cover to remove it (Figure 30).

_G002595

Figure 30

3. Replace the air filter.

4. Install the cover.

12

Changing the Engine Oil

Change the engine oil after the first 2 operating hours;
change it yearly thereafter.

Charging the Battery

Run the engine a %w minutes before changing the oil

to warm it. \'(;arm oil flows better and carries more

contflnliilflnts.

1. Re%r to Preparing for Maintenance.

2. Remove tile dipstick (Figure 31).

G002596

Figure 31

Tip tile mower onto tile right side to drain tile used oil
out through the oil fill robe (Figure 32).

Figure 32

4.

Slowly pour oil into tile oil fill tube until tile oil level
reaclles tile Full line on tile dipstick (Figure 33). Do not
overfill. (Max. fill: 20 oz., tspe: SAE 30W detergent
oil with an API service classification of SF, SG, SH, SJ,

SL, or lflgher.)

Battery posts, terminals, and related accessories
contain lead and lead compounds, chemicals

known to the State of California to cause cancer
and reproductive harm. Wash hands after handling

battery.

Charge the battery for 24 hours initiall?, then monthly
(ever? 25 starts) or as needed. Al\va_ s use the charger in a
sheltered area and charge tile battery at room termperamre
(70°F or 22°C) whenever possible.

1. Connect the charger to the mower wire harness located
below tile igifltion ke? (Figure 34).

G002889

Figure 34

2. Plug tile charger into a wall outlet.

Note: When the battery no longer holds a charge, recycle
or dispose of the lead-acid batter? according to local codes.

Replacing the Fuse

If tile batter_ does not charge or tile engine does not turn
with the electric starter, the fuse ma) be blown. Replace it
with a 40-amp plug-in tspe fuse. Refer to Installing tile Fuse.

Figure 33

5. Install tile dipstick secureh<

6. Dispose of tile used oil properl 3 at a local recscling
center.

Lubricating the Wheel Gears

1. Remove the wheel bolts on the rear wheels and remove
the rear wheels.

2. Appl? a lubricating oil to tile inner and outer sides of
tile gear as shown in Figure 35.

©

Figure 35

3. Install tile rear wheels.

13

Replacing the Blade

Important: You will need a torque wrench to install

the blade properly. If you do not have a torque wrench
or are uncomfortable performing this procedure,

contact an Authorized Service Dealer.

Important: A bolt torqued to 60 ft-lb (82 N-m)

is very tight. While holding the blade with a block
of wood, put your weight behind the ratchet or
wrench and tighten the bolt securely. This bolt is
very difficult to overtighten.

Examine tile blade whenever tot] mm out of gasoline. If tile
blade is damaged or cracked, replace it immediateh: If tile
blade edge is dull or _ficked, have it sllarpened or replace it.

The blade is sharp; contacting the blade can result
in serious personal injury.

Wear gloves when servicing the blade.

Disconnect tile spark plug wire from tile spark plug and
hook it onto tile retaining post. Refer to Preparing for

Maintenance.

2. Tip tl3e mower onto its side witl3 tile air filter up.

3. [sea block of wood to hold tile blade stead 3 (Figure

36).

Cleaning the Mower

The mower may dislodge material from under the

mower housing.

• Wear eye protection.

• Stay in the operating position (behind the
handle).

• Do not allow bystanders in the area.

1. \'('itll tile engine tutoring on a fiat paved surt;ace, spray a
stream of water in front of tile right rear wheel (Figure

Tile water will splash into tile path of tile blade, clea_fing
out tile clippings.

G002600

Figure 37

2.

\Vllen no more clippings come out, stop the water and
move tile mower to a drx area.

G002599

Figure 36

4. Remove tile blade, saving all mounting hardware (Figure

36).

5. Install tile new blade and a11mountilg hardware (Figure

36).

Important: Position the curved ends of the blade

to point toward the mower housing.

6. Use a torque wrench to tighten the blade bolt to
60 ft-lb (82 N-m).

3.

Run tile engine for a few minutes to dr) tile llousixg
to prevent it from rustin&

Storage

Store tile mower in a cool, clean, dr), place.

Preparing the Mower for

Storage

Gasoline vapors can explode.

• Do not store gasoline more than 30 days.

• Do not store the mower in an enclosure near an
open flame.

• Allow the engine to cool before storing it.

14

1. On the last refueling of the year, add fuel stabilizer to
tile fuel as directed by tile engine manut;acturer.

2. Dispose of any mmsed fuel properl?: Recycle it
according to local codes, or use it in tour automobile.

Note: Old fl_elin tile fl_el tank is tile leading cause of

}lard starting. Do not store fuel without stabilizer more
than 30 days, and do not store stabilized fuel more than

90 daxs.

3. Run the mower until the engine stops from intuiting
out of ft_el.

2. Fold the upper handle forward as shown in Figure 39.

|Ilrlport&llt: Route the cables to the outside of the
handle knobs as you fold the upper handle.

4. Prime the engine and start it again.

5. Allow the engine to run until it stops. When you can no
longer start the engine, it is sufiicientlv dry:

6. Disconnect the wire from the spark plug and connect
the wire onto the retaining post.

7. Remove the spark plug, add 1 oz. (30 ml) of oil through
the spark plug hole, and pull the starter rope slowh

several times to distribute oil throughout the cylinder to
prevent cylinder corrosion during the off-season.

8. Loosely install the spark plug.

9. Tighten all nuts, bolts, and screws.

10. Charge the batter? for 72 hours, then unplug the batter_
charger and store the mower in an unheated area. If you

must store the mower in a heated area, you must charge
the batter_ ever_ 90 da_s.

Folding the Handle

Folding or unfolding the handle improperly can
damage the cables, causing an unsafe operating

condition.

Figure 39

3. To unfold the handle, reverse the steps above.

Removing the Mower from

Storage

1. Remove the spark plug and spin the engine rapidl? using
the starter to blow the excess oil from the c_linder.

2. Install the spark plug and tighten it with a torque
wrench to 15 ft-lb (20 N-m).

3. Charge the batter_:

4. Connect the wire to the spark plug.

• Do not damage the cables when folding or
unfolding the handle.

• If a cable is damaged, contact an Authorized
Service Dealer.

Loosen the handle knobs until you can move the upper
handle fred? (Figure 38).

Figure 38

15

22in Recycler _

Walk Power Mowers

The Toro Total Coverage Guarantee

A Two -Year Full Warranty (Limited for Commercial Use)

and

The Toro Starting Guarantee on GTS-2 (Guaranteed to Start) Engines

A Two -Year Full Warranty (Not applicable for Commercial Use)

The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly promise to repair any Toro Product, when used for residential
purposes*, if defective in materials or workmanship or if it stops functioning due to the failure of a component. The following time periods apply from the date of original purchase:

• All Products and attachments • 2 year full warranty

• Batteries • 1yearfull warranty

Toro Products used for commercial, institutional, or rental use are warranted against defects in materials or workmanship for the followin 9 time periods from the original date of
purchase:

All Products and attachments 45 day limited warranty

This warranty covers the cost of parts and labor, but you must pay transportation costs. This warranty applies to all Toro Recycler walk power mowers and their attachments.

The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly guarantee that your Toro GTS-2 Engine, when used for residential
purposes*, will start on the first or second pull for two years from the date of original purchase, if you provide the routine maintenance it requires, or we will fix it free of charge.

This warranty covers the cost of parts and labor, but you must pay transportation costs. This warranty applies to all Toro Recycler walk power mowers.
The Toro Starting Guarantee does not apply when the product is used commercially. Use at more than one location is considered commercial use.

Conditions and Products Covered under The Toro Total Coverage Guarantee

Products Warranty Period

Limited Warranty for Commercial Use

Products Warranty Period

Conditions and Products Covered Under the Toro Starting Guarantee

The following applies to both the Toro Total Coverage Guarantee & the Toro Starting Guarantee:

Items and Conditions Not Covered

There is no other express warranty except for special emission system coverage on some products. This express warranty does not cover the following:

• Cost of regular maintenance service or parts, such as filters, fuel, lubricants, oil changes, air filter, blade sharpening/worn blade on mowers, paddles/scrapers/skids on
snowthrowers, cable/linkage adjustments, or brake and clutch adjustments

• Any product or part which has been altered or misused and requires replacement or repair due to accidents or lack of proper maintenance

• Repairs necessary due to improper battery care, electrical supply irregularities, failure to use fresh fuel (less than one month old), or failure to properly prepare the unit prior
to any period of non-use over one month

• Pickup and delivery charges

• Operational misuse, neglect, or accidents

• Repairs or attempted repairs by anyone other than an Authorized Toro Service Dealer

• Repairs or adjustments to correct starting difficulties due to the following:

• Special operational conditions where starting may require more than two pulls:

If you are having difficulty starting your unit, please check the Operotor's Manual to ensure that you are using the correct starting procedures. This can save an unnecessary visit to a
Service Dealer.

You must maintain your Toro Product by following the maintenance procedures described in the Operator's Manual. Such routine maintenance, whether pertormed by a dealer or by
you, is at your expense.

If you think that your Toro Product contains a defect in materials or workmanship, or if a normal, able-bodied adult can no longer stalt your product's engine in one or two pulls,

follow this procedure:

1. Contact any Authorized Toro Service Dealer to arrange service at their dealership. To locate a dealer convenient to you, refer to the Yellow Pages of your telephone directory (look
under "Lawn Mowers" or "Snow Removal") or access our website at www.Toro.com. U.S. Customers may also call the number listed in item #3 to use our 24-hour Toro dealer

Iocator system.

2. Brin 9 the product and your proof of purchase (sales receipt) to the Service Dealer. The dealer will diagnose the problem and determine if it is to be covered under warranty.

3. If for any reason you are dissatisfied with the Service Dealer's analysis or with the assistance provided, contact us at: Customer Care Department -Consumer, Toro Warranty
Company, 8111 Lyndale Avenue South, Bloomington, MN 55420-1196; or call us toll free at 1-866-214-9807 (U.S. customers) or 1-866-214-9808 (Canada (ustomers).

All repairs covered by these warranties must be performed by an Authorized Toro Service Dealer using Toro approved replacement parts.

Neither The Toro Company nor Toro Warranty Company is liable for indirect, incidental, or consequential damages in connection with the use of the Toro
Products covered by these warrantles, including any cost or expense of provldlng substitute equipment or servlce during reasonable perlods of malfunction

or non-use pendlng completion of repairs under these warranties.

Some states do not allow exclusions of incidental or consequential damages, so the above exclusions and llmltatlons may not apply to you. Thls warranty

glves you specific legal rights, and you may also have other rights which vary from state to state.

Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country,

province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact the Toro importer. If all other
remedies fail, you may contact us at Toro Warranty Company.

* Resldentla[ purposes m_ans use of the product on the same lot as your home Use at mor_ than one Iocatlon is considered commerda[ use, and the commercial use warranty would apply

Failure to follow proper maintenance procedures
Rotary mower blade striking an object; snowthrower auger/paddles striking an object

Contaminants in the fuel system
Improper fuel or fuel/oil mixture (consult your Operotor's Monual if in doubt)

Failure to drain the fuel system prior to any period of non-use over one month

First time starts after extended period of non-use over one month or seasonal storage
Cool temperature starts such asthose found in early spring and late autumn (applies to rotary mowers only)

Improper starting procedures

Owner Responsibilities

Instructions for Obtaining Warranty Service

General Conditions

Countries Other than the United States or Canada

374-0052 RevA