Toro Groundsmaster360 Product Literature

FEATURES

Groundsmaster® 360

100” Articulating Cutting Deck

Seriously advancing

• Requires Groundsmaster 360
mower with greater than 32 hp

• Rear discharge, full width of deck

• Wing decks articulate 15 degrees,
up or down

• 1”– 5” cutting height, adjustable
in .25” increments

• Wing decks fold up hydraulically
for transport

productivity.

The Groundsmaster® 360, with its faster ground speed compared to

out-front mowers, plus a 100” cutting deck equals a “lower cost to

operate” solution for large area mowing. Increase your acres per hour

mowing capacity up to 38% over a typical 72” deck by using a 100”

wide deck! Mounts to any Groundsmaster® 360 mower with a 35 hp

or larger engine and is built to last. This 5-blade cutting deck system is

PTO-driven and consists of a center deck with three, 18” cutting blades

and two wing decks, each with a single, 25” cutting blade. Wing decks

articulate 15 degrees up or down during mowing, but cannot be operated

independently. During transport or trailering, the wing decks fold up

hydraulically so you can quickly move to the

next location. The PTO automatically shuts

off when the wing decks are raised or

deck articulation exceeds 15 degrees –

for safe and easy operation.

©2014 The Toro Company
8111 Lyndale Ave. S.
Bloomington, MN 55420-1196
Printed in the U.S.A.
re v. 2/ 14

(Front QAS accessory shown is optional)

Call your Toro distributor at 1-800-803-8676

Groundsmaster® 360 – 100” Articulating Cutting Deck Specifications*

100" CUTTING DECK, MODEL 31101

HEIGHT OF CUT

WIDTH OF CUT

DECK CONSTRUCTION

DISCHARGE

WING DECK ARTICULATION

SPINDLE ASSEMBLY

CUTTER DRIVE

BLADES

BLADE TIP SPEED

DECK SUSPENSION

CASTOR WHEELS

BELT IDLER

DECK SKID

DECK ANTI-SCALP ROLLERS

ANTI-SCALP CUPS

DECK COVERS

CUTTING DECK DEPTH

WING DECK TRANSPORT LOCKS

WEIGHT

WIDTH

REQUIRED EQUIPMENT

OPTIONAL ACCESSORIES

CERTIFICATION

MOWING RATE

WARRANTY

1”-5” (25 - 127 mm) adjustable in 0.25” (6 mm) increments

100 in (254cm), by five blades

Center deck with two wing decks; Welded .120" (11 gauge) high strength steel with steel .180" (7 gauge) stiffener plates and .1046" (12 gauge) chambers.

Rear Discharge – complete width of deck.

15 degrees, up or down.

Ductile cast iron 9" (23 cm) diameter conical spindle housing; Dual greaseable tapered roller bearings; Spindle shaft is 1.25" (3.2 cm) diameter, solid cold finished
steel, and splined connection between spindle shaft and pulley; Welded blade retainer plus anti-scalp cups.

Isolation mounted, PTO driven gearbox with 1.25:1 spiral bevel gears. “B” section belt drive to all spindles.

Wing Decks: 25.2" (64cm) long,.25" (6mm) thick, 2.5 (63mm) wide, heat treated steel blade in each wing; Center Deck: Three 18"(45.7cm) long, .25" (6mm) thick,

2.5" (63mm) wide, heat treated steel blades.

16,000 ± 1,000 ft/min at 3250 engine rpm

Center deck is supported via 4 vertically suspended chains to the frame of the machine. Wing decks are supported by pin connections to center deck and castor
wheels on the ground. Hydraulic deck lift includes load holding check valves and gravity lower.

Four 8 x 3.50-4, 4-ply, smooth, pneumatic, sealed precision ball bearings. Tensioning caps, made from impact modified thermoplastic alloy, are used to hold the castor wheels on the castor arms.

Fixed and spring loaded idlers.

Replaceable, bolt-on, non-marking UHMW skid on both sides.

5

Anti-scalp cup located on each blade spindle.

Steel and plastic with rubber latch connectors.

4.25" (108 mm)

Manual latches (standard)

Approximately 790 lbs (358 kg)

Mow: 108" (274 cm) Transport: Overall width with wing decks raised: 88 in (223.5 cm); center deck is 54.5 in (138.4 cm) wide and 5" (12.7 cm) off ground when raised.

Specific completion kit for each Groundsmaster 360 model with > 32hp engine. Check with Toro Distributor for details

Leaf Mulching Kit (Model 31105) Available in July 2014

Cutting unit meets specification of American National Standard ANSI B71.4-2012, Safety Specifications for commercial turf care equipment. Cutting unit meets
specifications of European standard prEN836, CE approved.

Mow up to 8.0 acres/hr (3.2 hectare/hr) at 8 mph (12.9 km/hr). Assumes no overlap and 100% efficiency.

Two year limited

MOWING POSITION

100” (254 cm) Mowing Width

108” (274 cm) Total Width

TRANSPORT/TRAILERING POSITION

5” (12.7 cm)

54.5” (138.4 cm)

67” (170.2 cm)

73.5” (186.7 cm)

88” (223.5 cm) Total Width

12”

(30.5 cm)

18”

(45.7 cm)

30”

(76.2 cm)

* Specifications and design subject to change without notice. Products depicted in this literature are for demonstration purposes only.

Actual products offered for sale may vary in design, required attachments and safety features. Consult your local Toro Distributor.