Toro 30031, 30032, 30094, 30096, 30098 Setup Instructions
...
Commercial Walk-behind Mowers
Model No. All Commercial Floating Deck Walk-behind Mowers
Loose Parts
Use the chart below to verify that all parts have been shipped.
Form No. 3356-901 Rev B
Setup Instructions
Step
1
2
3
4
5
6
7
8
9
No parts required
Number 2 general purpose lithium
base or molybdenum base grease.
(Purchase separately.)
No parts required
No parts required
No parts required
No parts required
No parts required
Bulk electrolyte with 1.265 specic
gravity (Purchase from a battery
supply outlet.)
No parts required
Description
Qty.
–
1 tube Check the idler arms for grease.
–
–
–
–
–
80
ounces
–
Check the tire pressure.
Prepare the grass deector.
Adjust the anti-scalp rollers.
Check the engine oil level.
Add fuel to the machine.
Check the hydraulic oil level.
Activate the battery for Mowers
with Electric Start.
Charge the battery for Mowers with
Electric Start.
Use
10
11
© 2007—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
No parts required
Operator’s Manual
Parts Catalog
Engine Owner’s Manual
Registration Card
Safety Video
Key
Oil drain hose
–
1
1
1
1
1
1
1
Register at www.Toro.com. Original Instructions (EN)
Check the machine before delivery
to the customer.
Delivering the machine to the
customer.
Printed in the USA.
All Rights Reserved
Step
1
Checking the Tire Pressure
No Parts Required
Procedure
Pressure: 12 to 14 psi (83 to 97 kP a)
Pressure for 60 inc h mo w ers: 14 to 16 psi (97 to
110 kP a)
Note: T he front caster wheel is a semi-pneumatic
tire and does not need to be c hec k ed.
Chec k the air pressure in the dri v e tires .
2. Chec k the mo w er belt idler ar m for g rease
( Figure 2 or Figure 3 ).
3. Install the car rier co v er .
Figure 2
40 inch, 48 inch, and 52 inch Mower Deck shown
Figure 1
Step
2
Checking the Idler Arms for
Grease
Parts needed for this step:
1 tube
Procedure
1. R emo v e the car rier frame co v er .
Number 2 general purpose lithium base
or molybdenum base grease. (Purchase
separately.)
2
Step
4
Adjusting the Anti-Scalp
Rollers
No Parts Required
Procedure
Adjust the anti-scalp rollers; refer to Adjusting the
Anti-Scalp R ollers in the Operator’ s Manual.
Figure 3
36 inch Mower Deck shown
4. Under the engine dec k, c hec k the PTO dri v e
belt idler ar m for g rease .
Step
3
Preparing the Grass
Deector
No Parts Required
Procedure
Install the spring for the g rass deflector; refer to
R e placing the Grass Deflector in the Operator’ s
Manual.
Step
5
Checking the Engine Oil
Level
No Parts Required
Procedure
Before y ou star t the engine and use the mac hine ,
c hec k the oil lev el in the engine crankcase; refer
to Chec king the Engine Oil Lev el in the Operator’ s
Manual.
Step
6
Adding Fuel to the Machine
No Parts Required
Procedure
Add g asoline to the mac hine before star ting it.
R efer to y our Operator’ s Manual. for the cor rect fuel
and procedure .
3
Step
Batter y electr ol yte contains sulfuric acid
7
which is a deadl y poison and causes sev er e
bur ns.
Checking the Hydraulic Oil
Level for Mowers with Hydro
Drive
No Parts Required
Procedure
Before y ou star t the engine and use the mac hine ,
c hec k the h y draulic oil lev el in the tank; refer to
Chec king the Hy draulic Oil Lev el in the Operator’ s
Manual.
Step
8
Activating the Battery for
Mowers with Electric Start
Do not drink electr ol yte and a v oid contact
with skin, ey es or clothing . W ear safety
g lasses to shield y our ey es and r ub ber g lo v es
to pr otect y our hands.
Fill the batter y wher e clean w ater is al w ays
a v aila ble f or flushing the skin.
F ollo w all instr uctions and compl y with all
safety messa ges on the electr ol yte container .
1. R emo v e the batter y from the mac hine . R efer
to the Operator’ s Manual for instr uctions .
Important: Nev er fill the batter y with
electr ol yte while the batter y is installed on
the machine. Electr ol yte can be spilled on
other par ts and cause cor r osion.
2. Clean the top of the batter y and remo v e the
v ent caps ( Figure 6 ).
Parts needed for this step:
80
ounces
Procedure
Bulk electrolyte with 1.265 specic gravity
(Purchase from a battery supply outlet.)
Warning
CALIFORNIA
Pr oposition 65 W ar ning
Batter y posts, ter minals, and r elated
accessories contain lead and lead
compounds, chemicals kno wn to the State of
Calif or nia to cause cancer and r epr oducti v e
har m. W ash hands after handling .
Figure 4
3. Slo wly pour electrolyte into eac h batter y cell
until the lev el is up to the upper line on the
batter y case .
Important: Do not o v erfill the batter y
because electr ol yte (sulfuric acid) can
cause sev er e cor r osion and dama ge to the
chassis.
4
Figure 5
4. W ait fiv e to ten min utes after filling the batter y
cells . Add electrolyte , if necessar y , until the
electrolyte lev el is up to the upper line on the
batter y case .
5. Install the batter y v ent caps ( Figure 6 ).
Step
9
Charging the Battery for
Mowers with Electric Start
No Parts Required
Procedure
Charging the batter y pr oduces gasses that
can explode and cause serious injur y .
• K eep cigar ettes, spar ks and flames a w ay
fr om the batter y .
• Mak e sur e the ignition s witch is of f.
• V entilate when charging or using the
batter y in an enclosed space.
Figure 6
1. Fill caps 3. Lower line
2. Upper line
Important: Do not r un the machine with
the batter y disconnected; electrical dama ge
may occur to the engine.
Charg e the batter y . R efer to the Operator’ s Manual
for instr uctions .
Figure 7
5
Loading...