Greensmaster® 3250-D
Unmatched diesel power, innovative design and a lighter footprint make this the ideal greensmower for greens and
surrounding areas.
2015 Toro Commercial Equipment Guide 15-003-T Rev. 2/15
52
ENGINE
FUEL CAPACITY
TRACTION DRIVE
GROUND SPEED
TURF COMPACTION
STEERING
CONTROLS/GAUGES
ELECTRICAL FEATURES
SOUND LEVEL
OVERALL DIMENSIONS
TIRES
LEAK DETECTION
BACKLAPPING
BRAKES
SEAT
ROPS
CERTIFICATION
WARRANTY
Greensmaster® 3250-D Specifications
*
GREENSMASTER 3250-D, MODEL 04384
Kubota® 902 tier 4i, 3-cylinder liquid-cooled diesel engine. 55.0 cu. in. (902 cc). Full pressure lubrication, oil filter. 24.8 hp (18.5 kW) @ 3600 rpm. Engine governed
to 2760 rpm high idle, 1500 rpm low idle (no load).
6 gallons (22.7 liters). Biodiesel-Ready for use up to B-20 (20% biodiesel and 80% petroleum blend).
Hydraulic piston pump, closed loop system. 2WD Parallel Hydrostatic or 3WD Series Parallel piston pump closed loop system. Foot pedal forward and reverse; infinitely variable.
Forward-mowing speed is variable from 2-5 mph (3.2-8 km/h), adjusted by stop on pedal mechanism. Mow speed setting does not affect transport speed. Maximum
Greensmaster 3250-D transport speed is 8.8 mph (14.4 km/h), may be reduced by adjusting stop in footrest pan without affecting mow speeds. Reverse is 2.5 mph
(4.0 km/h) maximum.
10 psi (.68 bar) average at recommended minimum tire pressures, with a 200 lb. operator, and cutting units down.
Power steering. No-tool quick adjust steering arm position, with arm motion allowing a wide range of operator sizes. Steering cylinder has through shaft design for
accurate straight line steering.
Raise/lower-mow lever. Functional control lever (neutral, mow, transport). Foot operated traction drive and brakes. Hour meter
and 4 bulb warning cluster. Hand operated choke, throttle. Mechanical engine speed control.
Maintenance-free 12-volt battery with 530 minimum cold cranking amps at 0° F (-17.7° C) and 95 minutes minimum reserve capacity at 85° F (29.4° C) 40 amp
alternator, circuit fused at 40 amps. Ignition switch/key. Seat switch. High temperature engine kill override switch. Harness terminals, fuse slot, and console switch
location available for optional lights installation.
84 dBA at operator ear under normal conditions.
Width of Cut: 59.0" (150 cm) Overall Height: 77.5" (197 cm)
Wheel Tread: 50.5" (128 cm) Net Weight (no fuel, no operator): 1,216 lbs. (552 kg)
Wheel Base: 48.6" (123 cm) Reel Speed: Approx.1950 rpm @ 2760 rpm (Adjustable)
Overall Length (w/baskets): 93.9" (238 cm)
Overall Width: 68.0" (173 cm)
Three 19 x 10.5-8, 2 ply pneumatic tubeless demountable and interchangeable. Smooth tread (approx. 1290 rev/mile). 8-12 psi front; 8-15 psi rear.
Turf Guardian™ optional.
Standard equipment.
6" (15.2 cm) drum type mechanical with rack and pawl lock for parking.
Contour seat with high backrest. 7" (17.8 cm) fore/aft slider adjustment with two mounting positions, allowing 9" (22.8 cm) total seat travel. Operator manual tube
mounted on the seat back for easy access.
Roll over protection system standard.
Certified to meet ANSI specification B71.4-2012 and European CE standards with appropriate kits installed.
Two-year limited warranty. Refer to the Operator’s Manual for further details.
8 BLADE DPA CUTTING UNITS, 04618
11-BLADE DPA CUTTING UNITS, 04619 14-BLADE CUTTING UNITS, 04624
TRACTOR
HEIGHT OF CUT (HOC) RANGE
REEL WELDMENT
REEL BEARINGS
MAINTENANCE
REEL DRIVE
FRAME
AGGRESSIVENESS
BEDKNIFE
BEDKNIFE ADJUSTMENT
FRONT & REAR ROLLERS
GRASS SHIELD
TOTAL WEIGHT
* Specifications and design subject to change without notice. Products depicted in this literature are for demonstration purposes only.
Actual products offered for sale may vary in use, design, required attachments and safety features. Consult your local Toro Distributor.
2015 Toro Commercial Equipment Guide 15-003-T Rev. 2/15
These cutting units will mount on any Toro riding Greensmaster (excluding Greensmaster TriFlex 33xx/34xx series).
Cutting height is adjusted on front roller by two vertical screws and held by two locking cap screws. Bench HOC range is .062"-.297" (1.6-7.5 mm). With high HOC kit,
range is .285-1" (7.3-25.4 mm). Effective HOC may vary depending on turf conditions and bedknife installed.
Reels are 5" (13 cm) in diameter, 21" (53.3 cm) in length. High carbon steel blades are welded to 5 stamped steel spiders, and heat treated to RC 48-54 hardness. The
reel is ground for diameter and concentricity, and backgrind.
Two double row, self-aligning ball bearings, 30 +/-.1 mm inside diameter slip fit onto reel shaft with lock nut. Multiple seal barriers on both sides of bearing for
added protection. Reel position maintained by a wave washer with no adjusting nut.
No grease zerks, sealed bearing design eliminates daily maintenance.
The reel weldment shaft is a 1.375" (35 mm) diameter tube with drive inserts permanently pressed in both ends. A replaceable floating coupler with an internal eight
tooth spline is factory installed on the right end, and held in place by a snap ring. The floating coupler may be moved to the other end when the cutting unit is used
on the GR3250-D front right position.
Precision machined, die-cast aluminum cross member with two bolt-on die-cast aluminum side plates.
Aggressiveness stays constant throughout the life of the reel. Patented design.
Replaceable single edged EdgeMaxTM Microcut Bedknife is standard.
Dual screw, indexed “click” adjustment to the reel; detents corresponding positively to .0007" (.018 mm) bedknife movement for each position.
Front: Not included with cutting unit, purchased separately. Option between full, narrow-spaced and wide-spaced roller.
Rear: Steel full, 2" (5.1 cm) diameter with sealed bearings and through-shaft.
Non-adjustable shield with adjustable cut-off bar to improve grass discharge from reel in wet conditions.
8-blade: 72 lbs. (32.7 kg) with aluminum Wiehle Roller. 11-blade: 75 lbs. (34 kg) with aluminum Narrow Wiehle Roller. 14-blade: 78 lbs. (35 kg) with aluminum Wiehle Roller.
53
The Greensmaster 3250-D is manufactured
in Tomah, WI ISO 9002 Certified Plant.
Greensmaster® 3250-D Accessories
GREENSMASTER 3250-D ACCESSORIES
*
TRACTION UNIT ACCESSORIES
04477 3-Wheel Drive Kit
04479 Thatching Reel (Set of 1)
04494 Greens Spiker Kit
04495 Greens Tri-Roller Kit
30707 Armrest Kit
99-4506 Traction Tires
104-7701 Hydraulic Oil Cooler Kit
04554 Light Kit
120-1951 Spark Arrestor
04497 Leak Detector
112-0279 Front Wheel Weight Kit
100-6442 2WD Weight Kit
99-1645 3WD Weight Kit
100-6430 Hose Adapter Kit
105-9766 Radiator Screen Kit
104-9400 Ground Follow Kit
115-4510 Bimini Folding Shade
115-4754 Wireless Hour Meter
ROLLER OPTIONS
04626 Front Narrow Wiehle Roller (set of 3)
04627 Front Wide Wiehle Roller (set of 3)
04625 Front Full Roller (set of 3)
04628
04629 Anti-Bobbing Roller
71-1550 Cast Iron Rear Wiehle Roller
107-3514 Steel Wide Wiehle Roller
121-4675 Extended Wiehle Roller
04258 Extended Narrow Wiehle Roller
04267 Narrow Wiehle Roller (for paspalum)
107-3510 Steel Narrow Wiehle Roller
120-9595 Steel Rear Roller (standard)
125-5180 DPA Rear Roller Extension Kit
120-9600 High Height of Cut Kit
04249 Split Full Front Roller
04250 Split Narrow Wiehle Roller
Solid Steel Roller Kit
(front Wiehle & rear steel rollers)
CUTTING UNIT & REEL OPTIONS
04618 8-Blade Cutting Unit
04619 11-Blade Cutting Unit
04624 14-Blade Cutting Unit
119-4103 8-Blade Reel (Individual)
121-6651 8-Blade Reel, Heavy-Duty (Individual)
119-4104 11-Blade Reel (Individual)
127-2202 14-Blade Reel (Individual)
GROOMER OPTIONS
04709
04710 Groomer Drive (RH) (Set of 1)
04712
04713
04274
04275
112-9248 Groomer Pull Link Kit
04744 Grooming Reel - Thin Blade (Set of 1)
Groomer Drive (LH) (Set of 1)
Groomer Reel, Spring Steel (Set of 1)
Groomer Brush (Set of 1)
Greens Perfection Brush – Soft
Greens Perfection Brush – Stiff
SCRAPER OPTIONS
125-5303 Front Narrow Wiehle Roller Scraper
125-5304 Front Wide Wiehle Roller Scraper
125-5305 Front Full Roller Scraper
115-7377
115-7378
115-7379 Front Full Roller Scraper Brush
115-7380
115-7381
115-7382 Front Full Roller Scraper Comb
115-7383 Rear Roller Scraper
121-2260 Adjustable Rear Roller Scraper
04646
107-9561 Anti-Bobbing Roller Scraper Kit
04726
04724
Front Narrow Wiehle Roller Scraper Brush
Front Wide Wiehle Roller Scraper Brush
Front Narrow Wiehle Roller Scraper Comb
Front Wide Wiehle Roller Scraper Comb
Spring Loaded Rear Roller Scraper
(Set of 3)
Rotating Rear Roller Brush (LH) (Set of 1)
Rotating Rear Roller Brush (RH) (Set of 1)
BEDKNIFE & BEDBAR OPTIONS
93-4262 Microcut Bedknife
93-4263 Tournament Bedknife
93-4264 Low Cut Bedknife
94-6392 High Cut Bedknife
63-8600 Fairway Bedknife
108-4303 Extended Microcut Bedknife
108-4302 Extended Tournament Bedknife
115-1880
115-1881 EdgeMaxTM Tournament Bedknife
112-7475 EdgeMax
106-2648-01 Bedbar (Standard)
99-3794-03 Aggressive Bedbar
EdgeMaxTM Microcut Bedknife (Standard)
TM
Fairway Bedknife
THATCHING REEL ACCESSORIES
117-6824
119-1128
117-6839
117-6840
121-6675 Spring Steel Kit
121-6674 Blade, Spring Steel
121-9525 Thatching Reel Quick Change Kit
Thin dynaBLADE, (1.2mm Thickness)
(Individual)
Regular dynaBlade, (2mm Thickness)
(Individual)
Replacement Kit, 1.2mm
Blades)
Replacement Kit, 2mm
Blades)
dynaBlade
dynaBlade
(36
(36
BIO-HYDRAULIC FLUID / HYDRAULIC FLUID / OIL
119-2157
119-2158 Bio-Hydraulic Fluid, 55 gal. (208.2 L)
108-1178
108-1177
121-6393
121-6392
Bio-Hydraulic Fluid, 5 gal. (18.9 L)
Premium Hydraulic Fluid, 5 gal. (18.9 L)
Premium Hydraulic Fluid, 55 gal. (208.2 L)
Premium Engine Oil SAE 10W30, 5 gal. (18.9 L)
Premium Engine Oil SAE 10W30, 55 gal. (208.2 L)
TOOLS
04399 Turf Evaluator
125-5610
125-5611
94-9010
Paper – Reel
Shim – Reel
Height of Cut Bar Assembly
* Specifications and design subject to change without notice. Products depicted in this literature are for demonstration purposes only.
Actual products offered for sale may vary in use, design, required attachments and safety features. Consult your local Toro Distributor.
2015 Toro Commercial Equipment Guide 15-003-T Rev. 2/15
54
The Greensmaster 3250-D is manufactured
in Tomah, WI ISO 9002 Certified Plant.
Loading...