Page 1
Greensmaster® 3150-Q
The next generation of the world’s favorite riding greensmower.
2015 Toro Commercial Equipment Guide 15-003-T Rev. 2/15
49
Page 2
ENGINE
FUEL CAPACITY
TRACTION DRIVE
GROUND SPEED
TURF COMPACTION
IMPLEMENT DRIVE
STEERING
CONTROLS/GAUGES
ELECTRICAL FEATURES
TIRES/WHEELS/PRESSURE
BRAKES
HYDRAULIC OIL
LEAK DETECTION
SOUND LEVEL
OVERALL DIMENSIONS
WIDTH OF CUT
REEL SPEED
BACKLAPPING
CUTTING UNIT SUSPENSION
ROPS
CERTIFICATION
WARRANTY
Greensmaster® 3150-Q Specifications
*
GREENSMASTER 3150-Q, MODEL 04358
18 hp (13.4 kW) @3600 rpm, Briggs & Stratton® gasoline engine, governed to 2850 rpm high idle, 1650 rpm low idle. Air-cooled.
7 gallon (26.5 liter) capacity; unleaded gasoline.
Hydraulic piston pump, closed loop system. 2WD Parallel Hydrostatic or 3WD Series Parallel piston pump closed loop system. Foot pedal forward and reverse; infinitely variable.
Forward-mowing speed is variable from 2-5 mph (3.2-8 km/h), adjusted by stop on pedal mechanism. Mow speed setting does not affect transport speed. Maximum
Greensmaster 3150-Q transport speed is 8.8 mph (14.4 km/h), may be reduced by adjusting stop in footrest pan without affecting mow speeds. Reverse is 2.5 mph
(4.0 km/h) maximum.
8-10 psi (dependent on tire pressure) with operator and cutting units down.
Single gear pump, mono valve block, series reel drive to 3 motors.
Power steering. Adjustable steering wheel tilt and a 5-position steering arm tilt.
Raise/lower-mow lever (joystick). Functional control lever (neutral, mow, transport). Foot operated traction drive and brakes. Hour meter. Hand operated throttle and
choke. Mechanical engine speed control.
12-volt lead acid, group size U1, with 300 minimum cold cranking amps at 0° F and 34 minutes reserve capacity at 85° F/25 amps draw. 16 amp alternator. Ignition
switch/key. Seat switch. Harness terminals and fuse slot available for optional lights installation.
Three tires: Three 18 x 10.5-8, 4-ply pneumatic tubeless demountable and interchangeable with smooth tread.
8-12 psi front; 8-15 psi rear. Optional Traction Tire (4-ply): P/N 119-3516.
Two 6" (15.2 cm) drum type.
7.5 gallon (28.4 liter) tank with internal baffle. 1.0 gallon (3.8 liter) auxiliary tank.
Equipped with Turf Guardian™ leak detection system.
82 dB(A) at operator’s ear under normal conditions.
Wheel Tread: 49.5" (149.9 cm), Wheel Base: 47" (119 cm), Length: 90" (229 cm), Width: 69.7" (177 cm) w/reels, Height: 74.5" (189 cm), Weight: 1,087 lbs. (493 kg).
59" (150 cm)
Approximately 1975 RPM at 2850 engine RPM. Adjustable.
Standard equipment.
Cutting units are completely free-floating, each attaching to the tractor by direct pull links and lifted by a centered lift arm. Baskets are supported by carrier frames
that are ground following. Cutting unit floatation is unaffected by basket content. Grass baskets are all interchangeable and accessible from the front of the machine.
Roll Over Protection System standard.
Certified to meet ANSI specification B71.4-2012 and European CE standards with appropriate kits installed.
Two-year limited warranty. Refer to the Operator’s Manual for further details.
11-BLADE DPA CUTTING UNITS, 04619 14-BLADE CUTTING UNITS, 04624
TRACTOR
HEIGHT OF CUT
(HOC) RANGE
REEL WELDMENT
REEL BEARINGS
MAINTENANCE
REEL DRIVE
FRAME
AGGRESSIVENESS
BEDKNIFE
BEDKNIFE ADJUSTMENT
FRONT & REAR ROLLERS
GRASS SHIELD
TOTAL WEIGHT
* Specifications and design subject to change without notice. Products depicted in this literature are for
demonstration purposes only. Actual products offered for sale may vary in use, design, required attachments
and safety features. Consult your local Toro Distributor.
2015 Toro Commercial Equipment Guide 15-003-T Rev. 2/15
These cutting units will mount on any Toro riding Greensmaster (excluding Greensmaster TriFlexTM 33xx/34xx series).
Cutting height is adjusted on front roller by two vertical screws and held by two locking cap screws. Bench HOC range is .062"-.297" (1.6-7.5 mm). With high HOC kit,
range is .285-1" (7.3-25.4 mm). Effective HOC may vary depending on turf conditions and bedknife installed.
Reels are 5" (13 cm) in diameter, 21" (53.3 cm) in length. High carbon steel blades are welded to 5 stamped steel spiders, and heat treated. The reel is ground for
diameter and concentricity, and relief ground.
Two stainless steel ball bearings, 30 +/-.1 mm inside diameter slip fit onto reel shaft retained by internally splined threaded insert. Low drag seals/slingers for added
protection with o-ring sealed motor and counterweight. Reel position maintained by a wave washer with no adjusting nut.
No grease zerks, sealed bearing design eliminates daily maintenance.
The reel weldment shaft is a 1.375" (35 mm) diameter tube with internally splined threaded insert.
Precision machined, die-cast aluminum cross member with two bolt-on die-cast aluminum side plates.
Aggressiveness stays constant throughout the life of the reel. Patented design.
Replaceable single edged EdgeMaxTM Microcut Bedknife is standard.
Dual screw, indexed “click” adjustment to the reel; detents corresponding to .0007" (.018 mm) bedknife movement for each position.
Front: Not included with cutting unit, purchased separately. Option between full, narrow-spaced and wide-spaced Wiehle roller.
Rear: Steel full, 2" (5.1 cm) diameter with sealed bearings and through-shaft.
Non-adjustable shield with adjustable cut-off bar to improve grass discharge from reel in wet conditions.
8-blade: 72 lbs. (32.7 kg) with aluminum Wiehle Roller. 11-blade: 75 lbs. (34 kg) with aluminum Narrow Wiehle Roller.
14-blade: 78 lbs. (35 kg) with aluminum Wiehle Roller.
8 BLADE DPA CUTTING UNITS, 04618
50
The Greensmaster 3150-Q is manufactured in
Tomah, WI ISO 9002 Certified Plant.
Page 3
Greensmaster® 3150-Q Accessories
GREENSMASTER 3150-Q ACCESSORIES
*
TRACTION UNIT ACCESSORIES
04476 3-Wheel Drive Kit
04479 Thatching Reel (Set of 1)
04494 Greens Spiker Kit
04495 Greens Tri-Roller Kit
30707 Armrest Kit
119-3516 Traction Tires
04554 Light Kit
130-6536 Hydraulic Oil Cooler Kit
108-6472 Traction Speed Control Kit
104-6540 Spark Arrestor Screen
115-4510 Bimini Folding Shade
100-6442 2WD Weight Kit
99-1645 3WD Weight Kit
115-4754 Wireless Hour Meter
ROLLER OPTIONS
04626 Front Narrow Wiehle Roller (set of 3)
04627 Front Wide Wiehle Roller (set of 3)
04625 Front Full Roller (set of 3)
04628
04629 Anti-Bobbing Roller
71-1550 Cast Iron Rear Wiehle Roller
107-3514 Steel Wide Wiehle Roller
121-4675 Extended Wiehle Roller
04258 Extended Narrow Wiehle Roller
04267 Narrow Wiehle Roller (for paspalum)
107-3510 Steel Narrow Wiehle Roller
120-9595 Steel Rear Roller (standard)
125-5180 DPA Rear Roller Extension Kit
120-9600 High Height of Cut Kit
04249 Split Full Front Roller
04250 Split Narrow Wiehle Roller
Solid Steel Roller Kit
(front Wiehle & rear steel rollers)
CUTTING UNIT & REEL OPTIONS
04618 8-Blade Cutting Unit
04619 11-Blade Cutting Unit
04624 14-Blade Cutting Unit
119-4103 8-Blade Reel (Individual)
121-6651 8-Blade Reel, Heavy-Duty (Individual)
119-4104 11-Blade Reel (Individual)
127-2202 14-Blade Reel (Individual)
GROOMER OPTIONS
04709
04712
04713
04274
04275
106-2643 Groomer Pull Link Kit
04744 Grooming Reel - Thin Blade (Set of 1)
Groomer Drive (LH) (Set of 1)
Groomer Reel, Spring Steel (Set of 1)
Groomer Brush (Set of 1)
Greens Perfection Brush – Soft
Greens Perfection Brush – Stiff
SCRAPER OPTIONS
125-5303 Front Narrow Wiehle Roller Scraper
125-5304 Front Wide Wiehle Roller Scraper
125-5305 Front Full Roller Scraper
115-7377
115-7378
115-7379 Front Full Roller Scraper Brush
115-7380
115-7381
115-7382 Front Full Roller Scraper Comb
115-7383 Rear Roller Scraper
121-2260 Adjustable Rear Roller Scraper
04646
107-9561 Anti-Bobbing Roller Scraper Kit
04726
Front Narrow Wiehle Roller Scraper Brush
Front Wide Wiehle Roller Scraper Brush
Front Narrow Wiehle Roller Scraper Comb
Front Wide Wiehle Roller Scraper Comb
Spring Loaded Rear Roller Scraper
(Set of 3)
Rotating Rear Roller Brush (LH) (Set of 1)
BEDKNIFE & BEDBAR OPTIONS
93-4262 Microcut Bedknife
93-4263 Tournament Bedknife
93-4264 Low Cut Bedknife
94-6392 High Cut Bedknife
63-8600 Fairway Bedknife
108-4303 Extended Microcut Bedknife
108-4302 Extended Tournament Bedknife
115-1880
115-1881 EdgeMaxTM Tournament Bedknife
112-7475 EdgeMax
106-2648-01 Bedbar (Standard)
99-3794-03 Aggressive Bedbar
EdgeMaxTM Microcut Bedknife (Standard)
TM
Fairway Bedknife
THATCHING REEL ACCESSORIES
117-6824
119-1128
117-6839
117-6840
121-6675 Spring Steel Kit
121-6674 Blade, Spring Steel
121-9525 Thatching Reel Quick Change Kit
Thin dynaBLADE, (1.2mm Thickness)
(Individual)
Regular dynaBlade, (2mm Thickness)
(Individual)
Replacement Kit, 1.2mm
Blades)
Replacement Kit, 2mm
Blades)
dynaBlade
dynaBlade
(36
(36
BIO-HYDRAULIC FLUID / HYDRAULIC FLUID / OIL
119-2157
119-2158 Bio-Hydraulic Fluid, 55 gal. (208.2 L)
108-1178
108-1177
108-1197
108-1196
Bio-Hydraulic Fluid, 5 gal. (18.9 L)
Premium Hydraulic Fluid, 5 gal. (18.9 L)
Premium Hydraulic Fluid, 55 gal. (208.2 L)
Premium Engine Oil SAE 30, 5 gal. (18.9 L)
Premium Engine Oil SAE 30, 55 gal. (208.2 L)
TOOLS
04399 Turf Evaluator
125-5610
125-5611
94-9010
Paper – Reel
Shim – Reel
Height of Cut Bar Assembly
* Specifications and design subject to change without notice. Products depicted in this literature are for
demonstration purposes only. Actual products offered for sale may vary in use, design, required attachments
and safety features. Consult your local Toro Distributor.
2015 Toro Commercial Equipment Guide 15-003-T Rev. 2/15
51
The Greensmaster 3150-Q is manufactured
in Tomah, WI ISO 9002 Certified Plant.
Loading...