Toro 30839, 30807, 30809, 30849 Specifications

Groundsmaster® 3500-D / 3500-G / 3505-D

A breakthrough rotary mower that delivers a superior quality of cut for trimming golf courses and striping sports fields.

2015 Toro Commercial Equipment Guide 15-003-T Rev. 2/15

13

ENGINE

FUEL CAPACITY

CONFIGURATION

TRACTION DRIVE

GROUND SPEED/CLEARANCE

CONTROLS

GAUGES & DIAGNOSTICS

ELECTRICAL & INTERLOCKS

HYDRAULICS

STEERING

TIRES/WHEELS

BRAKES

OVERALL DIMENSIONS

WEIGHT

WARRANTY

CERTIFICATION

TYPE

WIDTH OF CUT

HEIGHT OF CUT

MOWING RATE

CONSTRUCTION

SPINDLE ASSEMBLY

ANTI-SCALP FEATURES

MULCHING KIT

BIMINI SUNSHADE

WORK LIGHT

UNIVERSAL SUNSHADE

Groundsmaster® 3500 -D Specifications

*

GROUNDSMASTER 3500-D, TIER 4 DIESEL MODEL 30807

Kubota,® 3-cylinder, liquid-cooled diesel. Power: 24.8 hp (18.5 kW) gross, at rated speed of 3000 rpm. Torque peak: 71.5 (52.7) Nm (lbs-ft) @ 2200 rpm. Displacement:
1123cc. High idle: 3200 rpm no load (uninstalled) 3100-3200 installed. Remote-mounted 5" Donaldson
Oil capacity 4 quarts (3.8 liters) with standard oil filter. Rear-mounted, cross flow 4-row radiator. EPA Tier IV Final Compliant.

11 gallons (42 liters). 2008 models Biodiesel-Ready for use up to B-20 (20% biodiesel and 80% petroleuml blend).

Rear mounted engine, front operator position. Two post ROPS, seat belt.

3-wheel drive in mow and transport. Series/Parallel™ hydrostatic, closed-loop transmission provides infinitely variable ground speed in forward and reverse. Variable
displacement piston type pump.

Mow: 0-6 mph (0-10 km/h), mow speed is factory preset at 6 mph but is adjustable; Transport: 0-9 mph (0-14km/h);
Reverse: 0-4 mph (0-6 km/h). Ground Clearance: 6" (15.3 cm).

Forward and reverse traction control pedals; mow/transport foot lever; hand activated parking break; hand operated ignition key switch; tilt steering wheel lock; PTO
switch; throttle; joystick control for deck raise and lower; cutting deck transport lock.

Fuel gauge and hour meter, light cluster with glow plug and charge indicator lights, low engine oil pressure and high coolant temperature warning lights (high
temperature safety shut off).

Traction pedal, operator presence in seat, PTO engage or disengage, and cutting deck mow or transport safety interlock switches. Parking break set prohibits
movement through traction pedal. 40 amp alternator and 12-volt, 585 CCA battery.

Open center, manual valves, gear pump hydraulic system. System capacity approximately 3.5 gallon (13.2 liter) reservoir.

Hydraulic power steering, tilt wheel.

20 x 10-10, 4-ply rating, Turf Tread tires. 20 x 12-10, 4-ply rating, Turf Tread Fronts.

Dynamic through hydrostatic transmission service brake. Hand actuated over center, drum type parking brake.

Height Length Width Wheelbase

70.8" (180 cm) w/ROPS 116" (295 cm) 71.8" (182 cm) with 68" (173 cm) WOC 59.5" (151 cm)

75.8" (193 cm) with 72" (183 cm) WOC

2,095 lbs. (950 kg) with cutting units.

Two-year limited warranty. Refer to operator’s manual for further details.

Complies with ANSI B71.4-2012 and EN5395.

®

air cleaner. Fuel filter/water separator.

CUTTING DECKS

3 Contour™ Plus 27" (69 cm) rear-discharge rotary with rear roller on each deck. Sidewinder system allows all three decks to slide right and left 12" (30 cm) of
center, 24" (61 cm) total travel. Mulching kit optional.

68" (173 cm), standard and 72" (183 cm) optional. Deck overhang for trimming is 12" (30.5 cm) at 68" (173 cm) width of cut and
14" (35 cm) at 72" (183 cm). Overlap: 6.5" (16.5 cm) at standard width of cut.

.75-4" (1.9-10.2 cm) in .25" (.6 cm) increments.

Mows up to 4.1 acres/h (1.7 hectares/h) at 6 mph (10 km/h) (assumes no overlap or stops).

10-gauge steel constructed chambers with 12-gauge welded reinforcements. 1.5" (3.8 cm) square x .25" (.6 cm) wall tube with
7-gauge side supports. Spindle support 3/16" (.48 cm) high-strength steel and 10-gauge exterior channels.

Ductile cast iron spindle housing. Dual greaseable tapered roller bearings. 1.25" (3.2 cm) diameter solid cold finished steel spindle shaft. Splined connection
between spindle shaft and pulley. Welded blade retainer plus anti-scalp cups

6" (15 cm) anti-scalp cups on each blade.

Model 30836

ACCESSORIES

Model 30358

Model 30841

Model 30349 (White), Model 30552 (Red)

* Specifications and design subject to change without notice. Products depicted in this literature are for demonstration purposes only.

Actual products offered for sale may vary in use, design, required attachments and safety features. See distributor for details on all warranties.

2015 Toro Commercial Equipment Guide 15-003-T Rev. 2/15

14

The Groundsmaster 3500-D is manufactured
in Tomah, WI ISO 9002 Certified Plant.