Toro 30031, 30032, 30070, 30071, 30074 Setup Instructions

...
0 (0)

Form No. 3365-264 Rev B

Commercial Walk-Behind Mower

All Commercial Floating and Fixed Deck Walk-behind Mowers

Setup Instructions

Loose Parts

Use the chart below to verify that all parts have been shipped.

Procedure

Description

Qty.

Use

 

 

 

 

1

No parts required

Unfold the crate.

 

 

 

2

No parts required

Check the tire pressure.

 

 

 

3

Number 2 general purpose lithium base

 

Check the idler arms for grease.

or molybdenum base grease. (Purchase

1 tube

(Floating Deck Models)

separately.)

 

 

 

 

 

4

Number 2 general purpose lithium base

 

Check the mower belt idler arm for

or molybdenum base grease. (Purchase

1 tube

grease. (Fixed Deck Models)

separately.)

 

 

 

 

 

5

No parts required

Prepare the grass deflector.

 

 

 

6

No parts required

Adjust the anti-scalp rollers. (Floating

Deck Models)

 

 

 

Muffler

1

 

 

Curved washer

4

 

7

Muffler shield

1

 

Bolt (M8 x 25mm)

4

Install the muffler (if needed).

Muffler clamp

1

 

 

 

 

Muffler shield bracket

1

 

 

Side lock nut

4

 

8

No parts required

Check the engine oil level.

 

 

 

9

No parts required

Add fuel to the machine.

 

 

 

10

No parts required

Check the hydraulic oil level.

 

 

 

11

Bulk electrolyte with 1.265 specific

80

Activate the battery for Mowers with

gravity (Purchase from a battery supply

ounces

Electric Start.

outlet.)

 

 

 

 

12

No parts required

Charge the battery for Mowers with

Electric Start.

 

 

13

No parts required

Check the machine before delivery to

the customer.

 

 

© 2010—The Toro® Company

Register at www.Toro.com.

Original Instructions (EN)

8111 Lyndale Avenue South

 

Printed in the USA.

Bloomington, MN 55420

 

All Rights Reserved

Procedure

Description

Qty.

Use

 

 

 

 

 

Operator’s Manual

1

 

 

Engine Owner’s Manual

1

 

 

Engine warranty literature

1

 

14

Registration Card

1

Delivering the machine to the customer.

Operator training material

1

 

 

Accessory brochure

1

 

 

Key

1

 

 

Oil drain hose

1

 

2

1

Unfolding the Crate

No Parts Required

Procedure

If the machine is in a metal crate, refer to the Packaging Crate Instructions included with the machine.

3

Checking the Idler Arms for Grease (Floating Deck Models)

Parts needed for this procedure:

1 tube

Number 2 general purpose lithium base or

molybdenum base grease. (Purchase separately.)

 

 

2

Checking the Tire Pressure

No Parts Required

Procedure

Pressure: 12 to 14 psi (83 to 97 kPa)

Pressure for 60 inch mowers: 14 to 16 psi (97 to 110 kPa)

Note: The front caster wheel is a semi-pneumatic tire and does not need to be checked.

Check the air pressure in the drive tires.

Procedure

1.Remove the carrier frame cover.

2.Check the mower belt idler arm for grease (Figure 2 or Figure 3).

3.Install the carrier cover.

Figure 2

40 inch, 48 inch, and 52 inch Mower Deck shown

Figure 1

3

Toro 30031, 30032, 30070, 30071, 30074 Setup Instructions

Figure 3

36 inch Mower Deck shown

4.Under the engine deck, check the PTO drive belt idler arm for grease.

4

Checking the Mower Belt Idler Arm for Grease (Fixed Deck Models)

Parts needed for this procedure:

1 tube

Number 2 general purpose lithium base or

molybdenum base grease. (Purchase separately.)

 

 

Procedure

1.Remove the mower deck cover.

2.Check the mower belt idler arm for grease (Figure 4).

3.Install the mower deck cover.

Figure 4

5

Preparing the Grass Deflector

No Parts Required

Procedure

Check if your machine has the grass deflector spring installed correctly. The grass deflector needs to have downward tension.

WARNING

An uncovered discharge opening could allow the lawn mower to throw objects in the operator’s or bystander’s direction and result in serious injury or death. Also, contact with the blade could occur.

Never operate the lawn mower with the grass deflector removed unless you install a cover plate, a mulch plate, or a grass chute and catcher.

1.Make sure the L end of spring is installed behind the deck edge before installing the bolt as shown in Figure 5.

2.Place the J hook end of spring around grass deflector (Figure 5).

Important: The grass deflector must be free to rotate with downward tension. Lift the deflector up to the full open position and ensure that it rotates freely without binding into the full down position.

4

Loading...
+ 8 hidden pages