Page 1
FORM NO. 3319–985
36” Recycler Kit
for Mid-Size Mowers
MODEL NO. 30142
Loose Parts
Note: Use the chart below to identify parts for assembly.
DESCRIPTION QTY. USE
Baffle
Bolt 5/16–18 x 5/8” (16 mm)
Flange nut 5/16–18
Blocker plate
Bolt 3/8–16 x 1” (25 mm)
Flange nut 3/8–16
Bolt 1/4–20 x 3/4” (19 mm)
Flange nut 1/4–20
1
1
6
1
1
1
2
2
Install Recycler baffle
Install blocker plate
INSTALLATION
INSTRUCTIONS
Cover plate
Bolt 3/8–16 x 3/4” (19 mm)
Flange nut 3/8-16
Kicker
Bolt 5/16–18 x 5/8” (16 mm)
Flange nut 5/16-18
Recycler blade 2 Replace standard blades on mower
Preparing the Mower
1
4
4
2
4
4
Cover discharge opening
Install kickers
3. Tilt the mower up and support with jack stands
to ease installation of kit.
1. Remove belt cover from top of mower.
2. Thoroughly clean underside of the mower. All
debris must be removed to ensure that baffles
and kickers will fit properly against the cutting
chamber.
4. Flip up discharge chute and remove the
discharge baffle near discharge opening (Fig. 1).
Note: Replace hardware in top of mower
when baffle is removed for safety and
to save for use when using mower to
side discharge.
The Toro Company – 1998
Printed in USA
All Rights Reserved
Page 2
Installation Instructions
2
POTENTIAL HAZARD
• Open holes in the mower expose you and
others to thrown debris.
WHAT CAN HAPPEN
• Debris thrown out of holes in the mower
can cause injury.
HOW TO AVOID THE HAZARD
• Never operate the mower without hardware
mounted in all holes in the mower.
• Install hardware in all open holes when the
Recycler kit is removed.
1
Figure 1
1. Discharge baffle
m–3923
3
2
1. Baffle
2. flange nut 5/16-18
Figure 2
3. Bolt 5/16–18 x 5/8”
(16 mm)
m–3924
3. Place the blocker plate inside cutting chamber
between the front and baffle. Secure blocker to
the front of mower with 3/8–16 x 1” bolt and a
3/8–16 flange nut, replacing existing caster
mounting hardware, and to the front of the baffle
with (2) 1/4–20 x 5/8” (16 mm) bolt and (2)
1/4–20 flange nuts (Fig. 2).
3
1
2
4
1
Installing the Baffle
1. Remove the (5) 5/16–18 x 5/8” (16 mm) carriage
bolt and 3/8” locknuts from the holes where the
baffles will be installed (Fig. 2).
Note: Save hardware for use when using
mower to side discharge.
2. Place the baffle inside cutting chamber with
studs through the top. Secure studs to top of
mower with (5) 5/16-18 flange nuts and to the
back baffle with a 5/16-18 x 5/8” (16 mm) bolt
and 5/16-18 flange nut (Fig. 2).
2
2
5
1. Blocker plate
2. Bolt 3/8–16 x 5/8” (16 mm)
3. Flange nut 3/8–16
m–3925
Figure 3
4. Bolt 1/4–20 x 5/8” (16 mm)
5. flange nut 1/4–20
Page 3
Installation Instructions
4. Place (4) 3/8-16 x 3/4” (19 mm) bolts, through
from outside of discharge cover plate. Secure
bolts with (4) 3/8-16 flange nuts (Fig. 4).
1
2
m–3926
Figure 4
1. Discharge cover plate
2. Bolt 3/8-16 x 3/4” (19 mm)
3. Flange nut 3/8-16
5. Tighten all mounting hardware securely.
Installing the Kickers
1. Measure from the spindle center lines, and locate
kickers as shown (Fig. 5). Right spindles 7/16”
(11 mm) off to the right and left spindle 1-7/8”
(48 mm) off to the left (Fig. 5).
3
2. Holding kickers tight against baffle, mark, center
punch and drill (2) 11/32” (9 mm) holes for each
kicker (Fig. 5).
1 (right) 2 (left)
3
3
m–3914
Figure 5
1. 7/16” (11 mm)
2. 1-7/8” (48 mm)
3. Mark, center punch and
drill 11/32” (9 mm) holes
Place (2) kickers inside the mower over drilled holes.
Secure each kicker with (2) 5/16–18 x 5/8” (16 mm)
bolts, through from the bottom of the mower, and (2)
5/16–18 flange nuts (Fig. 6).
.
3
2
1
m–3927
Figure 6
1. Kicker
2. Bolt 5/16–18 x 5/8”
(16 mm)
3. Flange nut 5/16-16
3. Tighten all mounting hardware securely.
3
Page 4
Installation Instructions
Installing the Recycler Blades
1. Remove the standard blades (Fig. 7). Refer to
Operator’s Manual.
2. Place the blade onto the bolt, over cone washer.
Select proper number of spacer(s) for
height-of-cut and slide bolt into spindle (Fig. 7).
IMPORTANT: The sail (curved part of the
blade) must be pointing toward the inside of
the mower to ensure proper cutting.
3. Install remaining spacer(s) for proper
height-of-cut and secure with thin washer and
nut (Fig. 7).
4. Torque the blade bolt to 75–80 ft. lb.
(101–108 Nm).
5. Rotate the blades to ensure that there is at least
1/8” clearance between the blades and baffles.
6. Remove jack stands and lower mower.
Removing Baffles for Side
Discharge Cutting
1. Thoroughly clean the mower.
2. Tilt the mower up and support with jack stands
to ease removal of kit.
3. Remove the mounting hardware from the baffle,
blocker plate, kickers and discharge cover plate.
Note: Save the hardware for use when
installing the baffle.
POTENTIAL HAZARD
• Open holes in the mower expose you and
others to thrown debris.
WHAT CAN HAPPEN
• Debris thrown out of holes in the mower
can cause injury.
4
1
2
1. High-lift lade
2. Blade bolt
3. Cone washer
4. Spacer
3
Figure 7
5. Tube
6. Thin washer
7. Nut
m–3779
7
6
4
• Never operate the mower without hardware
mounted in all holes in the mower.
• Install hardware all open holes when the
Recycler
is removed.
4. Install previously removed discharge baffle
HOW TO AVOID THE HAZARD
5
5. Install previously removed standard blades.
6. Remove jack stands and lower mower.
4
Loading...