Toro 25467, 25467E Installation Instructions

AuxiliaryControlKit

762BackhoeforRT1200Trencher

ModelNo.25467

ModelNo.25467E

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

FormNo.3378-123RevA

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

Description

Nopartsrequired

Startbutton
Rockerswitch3

Nopartsrequired

Nopartsrequired

RemovingtheConsolePanel

1.Parkthemachineonalevelsurfaceandlowerthe
backhoetotheground.

2.Shutofftheengine,andremovethekeyfromthekey
switch.

3.RotatethebatterydisconnectswitchtotheOff
position;refertotheOperator’ sManualforthemachine.

4.Removethe4hex-headbolts(3/8x1inch)and4
washers(3/8inch)thatsecuretheconsolepaneltothe
operatorconsoleforthebackhoe(Figure1).

Qty.

Use

–

1

–

–

Removetheconsolepanel.

Installthestartbuttonandrockerswitches.

Connectthebackhoewiringtothebuttonandswitches.

Installtheconsolepanel.

Figure1

©2014—TheToro®Company
8111LyndaleAvenueSouth
Bloomington,MN55420

Registeratwww.T oro.com.

1.Consolepanel3.Washer(3/8inch)

2.Operatorconsole4.Bolt(3/8x1inch)

5.Removethe3rectangularplugsfromtheconsolepanel
(Figure2).

Note:Discardthe3plugsafterremoval.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3378-123*A

Figure2

ConnectingtheBackhoe
WiringtotheButtonsand
Switches

1.Connectthe10-socketconnectorofthebackhoe
wiringharnessthatislabeledThrottletothe10-pin
connectoroftheinboardrockerswitch(Figure4).

Note:Thisistherockerswitchthatisclosesttothe
startbutton.

1.Rectangularplugs

2.Consolepanel

InstallingtheStartButtonand
RockerSwitches

1.Removethejamnutfromthestartbutton(Figure3).

Figure3

1.Consolepanel

2.Startbutton

2.Inserttheelectricalconnector,wires,andcaseofthe
startbuttonthroughthe15.8mm(5/8inch)holein
theconsolepanel(Figure3).

3.Securethestartbuttontotheconsolepanelwiththe
jamnut(Figure3)thatyouremovedinstep1.

4.Alignthe3rockerswitchedtothe3rectangular
openingsintheconsolepanel,andsnapthemintothe
panel(

Figure3).

Note:Ensurethatthealignmentkeyfortheswitchis
pointingtotheforwardedgeofthepanel.

3.Jamnut

4.Rockerswitch

Figure4

1.E-stopbutton

2.Startbutton6.Screw

3.Inboardrocker
switch(throttle)

4.Centerrocker
switch(backll
blade)

5.Outboard
rockerswitch
(propel)

7.Forkedterminal11.10-socket

8.2-socket
connector(start
button)

9.2-pinconnector
(backhoe
wiringharness)

10.10-socket
connector
(throttle)

connector
(backllblade)

12.10-socket
connector
(propel)

2.Connectthe10-socketconnectorofthebackhoewiring
harnessthatislabeledBladetothe10-pinconnector
ofthecenterrockerswitch(Figure4).

3.Connectthe10-socketconnectorofthebackhoewiring
harnessthatislabeledPropeltothe10-pinconnector
oftheoutboardrockerswitch(Figure4).

4.Connectthe2-pinconnectorofthebackhoewiring
harnesstothe2-socketconnectorofthestartbutton
(

Figure4).

5.Afteralloftheconnectionsaremade,verifythatthe
seatswitchandtheE-stopfunctionproperlybefore
operatingthemachine.

2

InstallingtheConsolePanel

1.Applymediumgrade(serviceremovable)thread
lockingcompoundtothethreadsofthe4hex-head
bolts(3/8x1inch)thatyouremoveinstep4of
RemovingtheConsolePanel.

2.Alignthemountingholesintheconsolepanelwiththe
mountingholesintheoperatorsconsole(Figure1).

3.Securethepaneltotheconsolewiththe4hex-head
boltsand4washers,andtorquethebolts51to65N-m
(38to48lb-ft).

4.RotatethebatterydisconnectswitchtotheOn
position;refertotheOperator’ sManualforthemachine.

Figure5

Operation

Theauxiliarycontrolkitisusedwiththebackhoetocontrol
theforwardandbackwardmovementofthemachine,the
enginespeed,andtheelevationofthebackllblade—from
theoperatorspositiononthebackhoe.

StartingandControllingthe Engine

1.Fromtheoperatingposition,ensurethatallofthe
controlsareintheNeutralposition,andthekeyswitch
intheOnposition;refertotheOperator’sManualfor
themachine.

Note:Iftheengineiscold,thewait-to-start-engine
indicatorwilldisplayinthecommandcenter.Wait
fortheengineheatertowarmtheengineinletbefore
movingtothebackhoe.

2.Sitintheoperatorseatforthebackhoe.

3.Pressthestartbutton(Figure5).

Note:Ensurethatallofthebackhoecontrolsare
intheNeutralpositionbeforestartingtheengine,or
suddenmotionoftheattachmentmayoccur.

1.Propel-rockerswitch

2.Backll-bladerocker
switch

3.Throttle-rockerswitch

4.Usethethrottle-rockerswitchtocontroltheengine
speedasfollows:

4.Startbutton

5.E-stopbutton

•Pressuponthethrottle-rockerswitchtoraisethe

enginespeed(Figure5).

•Pressdownonthethrottle-rockerswitchtolower

theenginespeed(

5.Shuttheengineoffasfollows:

Important:Intheeventofanemergency,press
theE-stopbuttonimmediately.

A.Lowertheenginespeedtoidlebypressingdown

onthethrottle-rockerswitch(Figure5).

Note:Allowtheenginetoidlefor3to5minutes.

B.PresstheE-stopbuttontoshutofftheengine

(Figure5).

C.Aftertheenginestops,resettheE-stop.

D.TurnthekeytotheOffpositionattheoperator

positionforthemachine.

Figure5).

Note:Iftheenginestartsandthenstops,donot
startbuttonagainuntilthestartermotorhasstopped
turning.

Important:

itstopsturning.
formorethan30secondsatonetime.Allowthe
startermotortocoolfor2minutesbeforeyou
operateitagain.Whenyouengagethestarter
motor,youshouldseewhiteorblacksmoke
comingfromtheexhaustpipe;ifyoudonot,check
thefuelsupply.

Do not

operatethestartermotoruntil

Do not

operatethestartermotor

3

RaisingandLoweringthe
BackllBlade

Usethebackll-bladerockerswitchtoraiseandlowerthe
backllbladeasfollows:

1.Pressdownontheupperhalfoftheblade-rocker
switchtoraisethebackllblade(

2.Pressdownonthelowerhalfoftheblade-rocker
switchtolowerthebackllblade(Figure5).

Figure5).

MovingtheMachineForward orBackward

Usethepropel-rockerswitchtomovethemachineforward
orbackwardasfollows:

1.Raisethebackllblade;refertoRaisingandLowering
theBackllBlade(page4).

2.Raisetheleftandrightstabilizersofthebackhoe;refer
totheOperator’sManualforthebackhoeattachment.

3.Lowerthethrottletoidle;refertoStartingand
ControllingtheEngine(page3).

4.Usethepropel-rockerswitchtomovethemachine
forwardorbackwardasfollows:

A.Pressuponthepropel-rockerswitchtomovethe

machineforward(Figure5).

B.Pressdownonthepropel-rockerswitchtomove

themachinebackward(

5.Onceyouareatthenewlocationwhereyouintendto
usethebackhoe,lowerthestabilizersandbackllblade;
refertoRaisingandLoweringtheBackllBlade(page

4)andtheOperator’ sManualforthebackhoeattachment.

Note:Donotmovethemachinetooclosetoahole,
especiallyifonsoftground.

Figure5).

4