Form No. 3398-624 Rev A
Dirt and Rock Stakes
2024 and 4045 Directional Drill
Model No. 23812
Model No. 23812E
Model No. 23813
Model No. 23813E
Model No. 23814
Model No. 23814E
Model No. 23815
Model No. 23815E
Installation Instructions
WARNING
CALIFORNIA
Proposition 65 Warning
This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm.
Loose Parts
Use the chart below to verify that all parts have been shipped.
Description |
Qty. |
Use |
|
|
|
|
|
2024 Dirt stakes |
2 |
|
|
2024 Rock stakes |
2 |
|
|
Coupler |
2 |
|
|
Stake pin |
2 |
|
|
O-ring |
2 |
|
|
Locknut (M12) |
8 |
Install the stakes on the 2024 directional drill. |
|
Bolt (M12-1 3/4 x 80 mm) |
8 |
|
|
Grease fitting |
2 |
|
|
Stake guide |
2 |
|
|
Guide ring |
2 |
|
|
Bolt (M8-1 1/4 x 20 mm) |
8 |
|
|
Rock or Dirt stake |
2 |
|
|
Guide ring |
2 |
Install the stakes for the 4045 directional drill. |
|
Stake guide |
2 |
||
|
|||
Bolts (M10-1 1/2 x 25 mm) |
6 |
|
© 2015—The Toro® Company |
Register at www.Toro.com. |
Original Instructions (EN) |
*3398-624* A |
8111 Lyndale Avenue South |
|
Printed in the USA. |
|
Bloomington, MN 55420 |
|
All Rights Reserved |
Installing the Stakes on the 2024 Directional Drill
Preparing the Machine and Installing
the Coupler
Note: Having 2 people or a lifting mechanism makes it easier to install the stakes.
1.Position the thrust frame 25.4 cm (12 inches) off the ground, with the stakes in the up position.
2.Turn off the engine and the battery disconnect switch.
3.If your machine has a cage, remove the stake-down cage assembly.
4.While holding the stakes, remove the O-rings and pins securing the stakes to the motors (Figure 1).
Figure 1
1. |
Motor |
3. |
Pin and O-ring (pin and |
|
|
|
e-clip on 4045) |
2. |
Coupler |
4. |
Stake |
5.Remove the existing stakes.
6.Remove the existing couplers and install the new couplers using 8 bolts (M12-1 3/4 x 80 mm), 8 locknuts (M12), and 2 grease fittings (Figure 2).
7.Torque the bolts to 127 to 155 N-m (94 to 114 ft-lb).
8.Pump grease into the fittings until grease begins to ooze out of the bearings (approximately 3 pumps) and wipe up any excess grease.
Installing the Dirt Stakes on the 2024 Directional Drill
Install the new stakes by aligning the hole in the stake with the hole in the motor coupler and secure it with the O-rings and pins included in this kit (Figure 3).
|
|
Figure 3 |
|
1. |
Coupler |
3. |
O-ring |
2. |
Pin |
4. |
Stake |
|
|
|
|
If your machine has a cage, install the cage assembly and latch the cage door.
|
|
Figure 2 |
|
1. |
Grease fitting |
3. |
Locknut (M12) |
2. |
Bolt (M12) |
4. |
Coupler |
|
|
|
|
2