• Inspect the air-cleaner elements.
• Grease the slicer-shaft bearings.
• Clean the air-cleaner elements. Clean them more frequently in dusty operating conditions.
• Clean under the belt cover.
• Inspect and adjust the spark plug; replace it if necessary.
• Replace the paper air-cleaner element. Replace it m ore f requently in dusty operating conditions.
Tool Rental Center
Tool Turn Guide
Supplier Website: www.Toro.com
PURPOSE
SAFETY
20in Turf Seeder
Model No. 23508—400000000 and Up
Supplier Technical Support #:
800-888-9926 (US and Canada)
Follow the directions below to maintain this tool.
Refer to the product Operator’s Manual for complete safety information.
Tool Inspection Process
Perform the necessary maintenance procedures as specified in the following table (for complete procedures, refer to the Operator’s Manual):
Maintenance Service Interval Maintenance Procedure
After the first 5 hours • Change the engine oil.
Before each use or daily
Every 25 hours
Every 50 hours
• Check the engine-oil level.
• Check the tire pressure.
• Check the blades for wear or damage.
• Check the seed gate.
• Clean the engine and exhaust area.
• Clean the debris buildup from under the machine.
• Check for loose fasteners.
• Check the condition of the belts.
• Change the engine oil.
• Check the spark arrester (if equipped).
Every 100 hours
Every 200 hours
Yearly or before storage • Touch up chipped paint.
Revision 1 12-15-2020 Toro Form No 3443-853 Rev A
• Change the hydraulic-transmission fluid.
• Replace the spark plug.
1. Spark-plug wire
Important: Refer to your engine owner’s manual for additional maintenance procedures.
Preparing for Maintenance
Before adjusting, cleaning, or repairing the machine do the following: park the
Regular cleaning and washing with mild detergent and water will increase the life span
Important:
Do not use brackish or reclaimed water to clean the machine.
Important:
Important:
machine with the engine running may result in internal engine damage.
Cleaning the Bottom of the Machine
1. Turn the fuel shutoff valve to the OFF position, and drain the fuel from
5. Fill the fuel tank.
Cleaning under the Belt Cover
1. Remove and retain the 4 bolts, lock washers, and 2 spacers securing the
3. Install the belt cover, and tighten all the hardware.
Cleaning the Seed Gate
1. Drain the fuel from the fuel tank.
6. Fill the fuel tank.
Cleaning the Engine Area
1. Clean all debris from the engine air-intake screen and around the engine.
machine on a level surface, disengage the drives, shut off the engine, wait for all
moving parts to stop, engage the parking brake, raise the blades, and disconnect the
spark-plug wire. After performing the maintenance procedure(s), connect the sparkplug wire to the spark plug.
2. Wipe up any excessive grease or oil around the engine.
the fuel tank.
2. Tilt the machine rearward until the upper handle rests on the ground, and
place a jack stand under the machine.
Note: If necessary, use 2 people to tilt the machine rearward.
3. Remove the debris with a hardwood scraper or other suitable device.
Avoid burrs and sharp edges.
4. Return the machine to the upright position.
belt cover to the left side of the machine.
2. Remove the cover, and brush out all the debris around the belt area.
Tool Cleaning Process
of the machine. For best results, clean the machine soon after each use.
Do not use power-washing equipment to wash the machine.
Power-washing equipment may loosen important decals or wash away
necessary grease at friction points. Avoid excessive use of water near the
control panel and engine.
Do not wash the machine with the engine running. Washing the
Revision 1 12-15-2020 Toro Form No 3443-853 Rev A
2. Tilt the machine rearward until the upper handle rests on the ground, and
place a jack stand under the machine.
Note: If necessary, use 2 people to tilt the machine rearward
3. Clean the debris between the frame and the seed gate.
4. Lubricate the sliding surface between the frame and seed gate with a dry
lubricant.
5. Return the machine to the upright position.
Loading...