Toro 22442 Installation Instructions

Page 1
Cement Mixer Bowl
For use with the Siteworks Systems Auger Drive Head
Model 22442
IMPORTANT: safety section in your traction unit operator’s manual, and follow all pr
Safety
1. Tipping exceed
Befor
ecautions listed ther
Decals
1
hazard—do not the maximum
e using this pr
#
100–4664
Figure 1
load
2. Maximum
oduct, read the
e.
2
load
Specifications:
Note:
Specifications and design are subject to change
without notice.
Overall Overall length Weight
width
25.15 inches (64 cm)
18.25 inches (46 cm) 75 lbs (34 Kg)
Installation
Instructions
Stability
To
determine the degree of slope you can traverse with the cement bowl installed on a traction unit, find the stability rating for the hill position you want to travel in the appropriate table on the following page, then find the degree of slope for the same rating and hill position in the Stability Data section of the traction unit operator manual.
IMPORTANT operator’ on the platform while using the cement bowl, or the traction unit will become unstable.
Ratings
’s
: If your traction unit has a r
s platform, the counterweight must be used
ear
WARNING
POTENTIAL HAZARD
Exceeding the maximum r can cause the traction unit to tip.
WHA
T CAN HAPPEN
If the traction unit tips, you or bystanders could be crushed.
HOW T
O AVOID THE HAZARD Do not drive the traction unit on a slope steeper than the maximum r determined in the following tables and the traction unit operator’s manual.
ecommended slope
ecommended slope, as
Maximum dry concrete load
The T
8111 Lyndale Ave. South Bloomington, MN 55420–1196
oro Company
– 1999
200 lbs (90.7 Kg)
All Rights Reserved
Printed in the USA
Page 2
Installation Instructions
Stability with a Loaded Bowl
Orientation
Front Uphill
Stability Rating
B
Rear Uphill
2.
Manually rotate the auger drive head up, until you can install two bolts into the holes on both sides of the cradle arms, securing the drive head. Secure each bolt with a nut (Fig. 2).
3
1
2
m–3944
D
Side Uphill
C
Stability with an Unloaded Bowl
Orientation
Front Uphill
Stability Rating
C
Rear Uphill
C
Side Uphill
Figure
1. Drive
2.
3. Start
4.
1. Drive
5. Stop
6.
head
Cradle arm
the engine.
Maneuver the drive shaft into the collar on the back of the bowl (Fig. 3).
1
2
Figure
head
the engine.
Secure the bowl to the drive head with the bolt and nut supplied with the auger drive head (Fig. 4).
1
2
3.
Bolts and nuts
3
2.
Cement bowl
m–4316
Installing
the Bowl onto the
Auger Drive Head
1. Raise
the loader arms so the drive head clears the
ground and stop the engine
2
B
2
Figure
1. Bolt 2. Nut
4
m–4317
Page 3
Installation Instructions
Mixing
POTENTIAL
When full of concr and could unbalance the traction unit.
WHA
The traction unit could tip, seriously injuring you or bystanders.
HOW T
Never use the cement bowl on the Dingo without first installing the Sitework Systems Counterweight, available fr dealer. Always keep the bowl close to the gr
1.
Lower the loader arms as far as possible while tilting the bowl upward as far as possible.
2.
Add up to 200 lbs (90.7 Kg) of dry concrete mixture.
3.
Move the throttle lever to the fast position (rabbit).
4.
If your traction unit has a speed selector and flow divider and the flow divider control to the 10 to 11 o’clock position (20 to 30 RPM).
and Pouring Concrete
HAZARD
ete, the bowl is very heavy
T CAN HAPPEN
O AVOID THE HAZARD
om your T
, move the speed selector lever to fast (Rabbit),
oro
ound.
Removing
the Bowl from the
Auger Drive Head
1. Set
the bowl down in its storage location.
2.
Stop the engine.
3.
Remove the bolt and nut securing the drive head to the bowl.
Start the engine and back the traction unit away from
4.
the bowl.
Storage
1.
Before long term storage, wash the bowl with mild deter
gent and water to remove dirt and grime.
2.
Store the bowl in a clean, dry garage or storage area. Cover it to protect it and keep it clean.
5.
Push the auxiliary hydraulics lever away from the operator grip to mix the concrete and add the appropriate amount of water
When the cement is suf
6.
auxiliary hydraulics lever to neutral and drive slowly to the work site.
7. T
ilt the bowl forward and pull the auxiliary hydraulics lever to the operator grip and hold it to dump the concrete.
When finished using the bowl, wash it out before the
8.
concrete sets.
.
ficiently mixed, move the
3
Page 4
Loading...