Toro 22425 Operator's Manual

Power Box Rake

for Compact Utility Loaders

Model No. 22425—Serial No. 240000001 and Up

Form No. 3353-855 Rev A

Operator’s Manual

Original Instructions (EN)

Contents

Page

Introduction 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Safety 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Safety and Instruction Decals 3. . . . . . . . . . . . . . . . .

Specifications 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Stability Ratings 5. . . . . . . . . . . . . . . . . . . . . . . . . . .

Setup 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Extending the Caster Wheels 5. . . . . . . . . . . . . . . . .

Operation 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Setting the Barrier Gap 5. . . . . . . . . . . . . . . . . . . . .

Starting the Power Rake 6. . . . . . . . . . . . . . . . . . . . .

Using the End Plates 6. . . . . . . . . . . . . . . . . . . . . . .

Angling the Roller 6. . . . . . . . . . . . . . . . . . . . . . . . .

Operating Tips 6. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Maintenance 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Recommended Maintenance Schedule 7. . . . . . . . .

Lubricating the Pivot Points 8. . . . . . . . . . . . . . . . . .

Inspecting and Servicing the Drive Chain 8. . . . . . .

Changing the Oil in the Chain Case 8. . . . . . . . . . . .

Storage 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Troubleshooting 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Introduction

Read this manual carefully to learn how to operate and maintain your product properly. The information in this manual can help you and others avoid injury and product damage. Although Toro designs and produces safe products, you are responsible for operating the product properly and safely.

You may contact Toro directly at www.Toro.com for product and accessory information, help finding a dealer, or to register your product.

Whenever you need service, genuine Toro parts, or additional information, contact an Authorized Service Dealer or Toro Customer Service and have the model and serial numbers of your product ready. You will find the model and serial number on a plate located on the product.

Write the product model and serial numbers in the space below:

This manual identifies potential hazards and has special safety messages that help you and others avoid personal injury and even death. Danger, Warning, and Caution are signal words used to identify the level of hazard. However, regardless of the hazard, be extremely careful.

Danger signals an extreme hazard that will cause serious injury or death if you do not follow the recommended precautions.

Warning signals a hazard that may cause serious injury or death if you do not follow the recommended precautions.

Caution signals a hazard that may cause minor or moderate injury if you do not follow the recommended precautions.

This manual uses 2 other words to highlight information.

Important calls attention to special mechanical

information and Note: emphasizes general information worthy of special attention.

Safety

To ensure maximum safety and best performance, and to gain knowledge of the product, it is essential that you and any other operator of the product read and understand the contents of this manual before the engine is ever started.

This is the safety alert symbol. It is used to alert you

to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.

Improperly using or maintaining this product could result in injury or death. To reduce this potential, comply with the following safety instructions.

Danger

Contact with rotating teeth can cause entanglement, severe wounds, and/or death.

• Keep away from the rotating teeth while

operating the power rake.

• Keep your hands, feet, other parts of your body,

and clothing away from rotating parts.

• Before adjusting, cleaning, repairing, and

inspecting the power rake, lower the power rake and loader arms to the ground, shut off the engine, and remove the key.

Model No.

Serial No.

W 2005 by The Toro Company 8111 Lyndale Avenue South Bloomington, MN 55420-1196

Printed in the USA

Danger

Warning

If there are buried power, gas, or telephone lines in the work area, you may contact them, causing a shock or an explosion.

Have the property or work area marked for buried lines and do not operate the power rake in marked areas.

Warning

When the engine is off, an attachment in the raised position can gradually lower, possibly pinning or injuring someone.

Always lower the attachment lift each time you shut off the traction unit.

Hydraulic fluid escaping under pressure can penetrate the skin and cause injury. Fluid injected into the skin must be surgically removed within a few hours by a doctor familiar with this form of injury, or gangrene may result.

• Keep your body and hands away from pin hole

leaks or nozzles that eject high-pressure hydraulic fluid.

• Use cardboard or paper to find hydraulic leaks;

never use your hands.

Caution

Hydraulic couplers, hydraulic lines and valves, and hydraulic fluid may be hot. If you contact hot components, you may be burned.

• Wear gloves when operating the hydraulic

couplers.

• Allow the traction unit to cool before touching

hydraulic components.

• Do not touch hydraulic fluid spills.

Safety and Instruction Decals

Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost.

93-7321

1. Cutting/dismemberment hazard of hands and feet, rotating knives—stay away from moving parts.

93-9367

1. Crushing hazard of hand—keep hands a safe distance from the hazard area.

100-4708

1. Thrown object hazard—Keep bystanders a safe distance from the traction unit.

Specifications

Note: Specifications and design are subject to change without notice.

Raking width

48 inches (122 cm)

Roller type Carbide toothed roller

7-inch (18 cm) diameter

Roller angle (angling

20° in both directions

model only)

Gap (tube to barrier) 1-1/8 to 1-3/4 inch (2.9

to 4.4 cm) adjustable

Tires 13 x 5.00

Tire Pressure 20 psi (137 kPa)

Weight (angling rake) 510 lbs (232 kg) max.

Oil capacity of the

approx. 1.5 pints (.71 l)

chain case

1. Roller

2. Chain case

3. End plate

4. Roller bearing (2)

m-7592

Figure 1

5. Caster lock pin (2)

6. Caster locking handle (2)

7. Barrier

8. Barrier gap adjustment

9. End plate pin (2)

10. Hairpin (2)

11. U-bolt

12. Oil drain cover

13. Fill hole plug

14. Level hole plug

+ 8 hidden pages