Toro 132-3128 Parts Catalogue

Form No. 0453-635
Arctic Cat® Prowler
Installation Instructions - Accessory Kit
(p/n 1436-877)
NOTE: Read these Installation Instructions thoroughly before beginning the installation process. Retain these Installation Instructions for future reference.
Application: All Prowler models
Kit includes:
p/n QTY DESCRIPTION
0541-852 1 Heater 1441-934 2 Side Mounting Bracket 1441-935 1 Rear Mounting Bracket (Left-Side) 1441-978 1 Rear Mounting Bracket (Right-Side) 1441-936 1 Vent Hose (2 in. x 10 ft) 1441-937 4 Round Adjustable Vent 0541-896 1 Vent Hose “Y” Fitting 1441-939 1 Heater Hose (20 x 3/4-in.) 1441-940 1 Radiator Hose Tee 1441-941 1 Radiator Hose Wye 1441-942 7 Hose Clamp (12) 1441-943 4 Hose Clamp (20) 1441-944 4 Hose Clamp (3/8 in.) 1441-945 10 Cable Tie (14 in.) 1441-946 5 Cable Tie (7 in.) 1441-947 1 Cable Tie (4 in.) 1441-948 1 Switch 0541-853 1 Harness w/Fuse 1441-950 1 Formed Hose (3/4-in. (Twist)) 1441-979 1 Formed Hose (3/4 x 9.375-in.) 1441-980 1 Formed Hose (3/4 x 8 1/2-in.) 1441-951 1 Coolant Hose (3/8-in x 18-in.) 1441-952 1 Fill Tee 1441-953 1 P-Clip 1441-954 1 Split Loom (1/4 in. x 12 in.) 1441-955 1 Split Loom (3/8 in. x 12 in.) 0123-010 4 Expansion Nut 1441-956 1 Coupling (3/4-in.) 0541-854 1 Coolant Pump 1441-957 1 Pump Coupling (3/4) 1441-958 1 Pump Coupling (3/8) 1436-408 1 Hardware Kit 0453-635 1 Instructions
Fig. 1
ROV-049
3. Secure Right- and Left-Side Rear Mounting Brackets to the top mounting locations of the side mounting brackets (with brackets flush on the bot­tom) using two screws and nuts (included in hard­ware kit). See Fig. 2.
Fig. 2
NOTE: Specific models may not have the under hood storage assembly which must be ordered and installed before installing this heater kit.
!WARNING
Allow the engine/cooling system to cool before installing this kit.
1. Remove the hood assembly and set aside. Retain all hardware.
2. Secure Side Mounting Brackets (with flange to the rear) to Heater so brackets are flush with heater using four machine screws (included in Hardware Kit). Tighten securely. See Fig. 1.
ROV-050
4. Place heater into storage box so side mounting brackets are approximately four inches below the storage box lip and up against the operator’s-side storage box wall. Mark all four mounting loca­tions. See Fig. 3.
1
Fig. 3
ROV-051
5. Using a 3/8-in. drill bit, drill all four locations; then install four Expansion Nuts.
6. On Prowlers without power steering, use a 2 1/4-in. hole saw and drill two holes in the bottom of the storage box; then drill a hole in the vertical side of the storage box below the bottom-left well nut and through the inner fender panel. See Fig. 4 and 6.
Fig. 4
7. Insert adequate lengths of 2-in. Vent Hose into each opening; then while holding the heater, attach each vent hose to the heater flange (shown below) and secure with three Cable Ties (14 in.). See Fig. 6.
Fig. 6
UTV-132A
CAUTION
On power steering models, all three holes will have to be drilled through the back of the storage box. Failure to follow this step will result in dam­age to the electronic power steering assembly. See Fig. 5 and 6.
Fig. 5
ROV-372A
8. Secure heater to the storage box using four machine screws (included in hardware kit).
9. Using a 1-in. hole saw, drill an opening in the stor­age box left corner; then route Coolant Hose (3/8­in. x 18-in.) down to lower radiator hose. See Fig.
6.
10. Using two suitable hose clamping devices, clamp the lower radiator hose in two positions; then cut the radiator hose. Install Radiator Hose Tee and secure with three Hose Clamps (3/8 in.). See Fig. 7.
Fig. 7
UTV-278A
UTV-126
2
Loading...
+ 3 hidden pages