Toro 132-3119 Parts Catalogue
Form No. 0453-893
Arctic Cat
®
Installation Instructions - Accessory Kit
Firebar 9-54 LED Light Bar Kits
(p/n 1436-857/858/859/860/861)
NOTE: Read these installation instructions thoroughly before beginning the installation process. Retain these Instal-
lation Instructions for future reference.
Kit includes:
Ref. No. p/n QTY DESCRIPTION
1 N/A 1 LED Light
2. N/A 2 Mounting Foot Bracket *
3 N/A 2 Isolated Rubber Mount *
4N/A2Cap Screw *
5 N/A 2 Nyloc Nut *
N/A N/A 1 Allen Wrench
N/A 1436-874 1 Harness (9-36 LED Light Bars)
N/A 1436-867 1 Harness (54 LED Light Bar)
N/A 2441-358 1 Single Row Light Bar Switch
N/A 2441-357 1 Dual Row Light Bar Switch
N/A 0453-893 1 Instruction
* Included in Single Row Hardware/Mounting Kit (p/n 0541-961)
* Included in Dual Row Hardware/Mounting Kit (p/n 0541-964)
Installing Light
NOTE: The light can be mounted using Fi rebar Tube
Clamps, Fast Clamps or many other styles of clamps.
See Fig. 1.
NOTE: The light can be mounted using Fi rebar Tube
Clamps, Fast Clamps or many other styles of clamps.
See Fig. 1.
NOTE: The light can be mounted using Firebar Tube
Clamps, Aluminum Lig ht Suppo rt, or man y other s tyles of
clamps and mounts. For some examples see Fig. 1 and 2.
Fig. 1
!WARNING
Do not look directly into lights; doing so can cause
eye damage.
!WARNING
After installing lights be sure to position lamps so they
do not blind other drivers. Position your vehicle
approximately 20 feet from a wall. The top of the beam
projected on the wall should be 3 inches lower than
the lights center.
CAUTION
The housing and end caps of the light as well as the
protruding short wiring lead and connector is fully
sealed and should not be opened or cut. Doing so
could damage the product and will void warranty.
CAUTION
Do not have lights on when starting or turning off the
vehicle.
ROV-304A
Fig. 2
ROV-306A
NOTE: The light can also be mounted almost anywhere
using the provided hardware and mounting foot bracket.
Washers or other backing materials (not provided) may be
required depending on the surface and/or material the light
is mounted to. See Fig. 3 and 4.
Fig. 3
ROV-302
Fig. 4
ROV-298
1. After the light is mounted in the desired location, keep
bottom base nuts snug but don’t tighten. Adjust bar so it
is centered. Tighten bolt on the bottom of the bracket to
20 ft-lb.
2. Adjust the light to the desired horizontal height, then use
the supplied Allen Wrench to tighten both allen screws
on each end. A good reference point is at a distance of
20 feet, the top of the beam should be three inches down
from the center of the light.
3. If installing Firebar 9-36 light on a roof or other flat
surface, use a 3/4-in. drill bit to drill through the surface; then route the pigtail wire and connector through
the surface and secure the grommet in the surface. DO
NOT cut the wire or connector. See Fig. 5.
4. If installing Firebar 54 light on a roof or other flat surface, use a 1-in. drill bit to drill through the surface;
then route the pigtail wire and connector through the
surface and secure the grommet in the surface. DO
NOT cut the wire or connector. See Fig. 5.
Fig. 5
1. There is an accessory plug near the back of the gauge or
remove seats and center console as necessary to access
the accessory plug near the battery or contact your Arctic Cat dealer for updated locations of accessory plugs.
Note the location and ensure the accessory plug on the
light wire harness can reach the vehicle accessory plug.
Do not plug in at this time.
NOTE: If powering multiple accessories from one
accessory plug, Accessory Adapters (p/n 1639-623 or
1639-624) are available.
NOTE: On HDX models, the accessory plug is under
the seat base near the throttle body.
2. Disconnect the positive battery cable then the negative
cable from the battery.
3. Route the battery terminals from the light harness to the
battery and to the location of the LED light and switch
(in the dash or desired location).
4. Secure the harness to the LED light; then plug the light
harness accessory plug into the accessory plug (A) on
the vehicle from step 1 of Installing Harness. See Fig. 6.
Fig. 6
ROV-298
5. Secure the yellow ring terminal from the light harness
and the red positive cable to the positive terminal on the
battery. Tighten securely.
6. Secure the black ring terminal from the light harness
and the black negative cable to the negative terminal on
the battery. Tighten securely.
NOTE: Verify wiring is correct and secure all loose wiring from any moving components. If the harness is not
plugged into the switch, the wires must be connecte d in
the order shown below. See Fig. 7.
ROV-341
NOTE: The grommet can be cut and removed if not in use.
Installing Harness
NOTE: On 2012 Wildcat models, Accessory Extension
Wire Harness (p/n 0486-467) is required but not included
in this kit and will have to be ordered separately. The
accessory plug is under the dash near the back of the
gauge and route toward the battery making sure wires
are cable tied away from the drive shaft.
®™Trademarks of Arctic Cat Inc., Thief River Falls, MN 56701 0913
Fig. 7
ROV-298
2
Loading...