Toro 110-3946 Installation Instructions

Form No. 3355-109 Rev A
Gusset Kit
For Z593 Series Z Master Mowers
Model No. 110-3946
Installation Instructions
Note: Deter mine the left and right sides of the mac hine from the nor mal operating position.
Loose Parts
Use the chart below to verify that all parts have been shipped.
Gussets 2 Bolt (3/8 x 1 inch)
1
2
Bolt (3/8 x 7/8 inch) Flange nut (3/8 inch) Gussets 2 Bolt (3/8 x 1 inch) Bolt (3/8 x 7/8 inch) Flange nut (3/8 inch)
Step
1
Drilling the Holes for the Gussets
Parts needed for this step:
2 Gussets 1
Bolt (3/8 x 1 inch)
1
Bolt (3/8 x 7/8 inch)
2
Flange nut (3/8 inch)
Description
Qty.
1 1 2
1 7 8
Use the gussets as a template to drill the new holes.
Install the new mounting plate.
Use
Procedure
1. Clean any debris from the rear frame of the mac hine .
2. T o mark the holes for the left gusset, remo v e the bolt holding the fix ed idler pulley brac k et as sho wn in Figure 1 .
© 2005—The Toro® Company 8111 Lyndale Avenue South Bloomington, MN 55420
Register at www.Toro.com. Original Instructions (EN)
Figure 1
1. Fixed idler pulley bracket
2. Bolt to remove 4. Hole to use
3. Nut
3. Install the left gusset with a bolt (3/8 x 1 inc h) and a flang e n ut (3/8 inc h) through the existing hole in the fix ed idler brac k et and frame ( Figure 2 .) Do not o v er tighten the bolt and mak e sure the gusset is ag ainst the rear frame .
4. T o mark the holes for the right gusset, use the existing hole in the frame as sho wn in ( Figure 2 .).
Printed in the USA. All Rights Reserved
5. Install the right gusset with a bolt (3/8 x 7/8 inc h) and a flang e n ut (3/8 inc h) through the existing hole in the frame . Do not o v er tighten the bolt and mak e sure the gusset is ag ainst the rear frame .
1. Drill 13/32 inch diameter holes here
Figure 3
2. Gusset
Figure 2
1. Bolt, (3/8 x 1 inch) 4. Flange nut (3/8 inch)
2. Existing hole
3. Gusset
5. Bolt,(3/8 x 7/8 inch)
6. Mark and center punc h the locations for the holes in the gussets ( Figure 3 ).
7. R emo v e the gussets and drill 13/32 inc h diameter holes at the mark ed locations ( Figure 3 ).
Step
2
Installing the Gussets
Parts needed for this step:
2 Gussets 1
Bolt (3/8 x 1 inch)
7
Bolt (3/8 x 7/8 inch)
8
Flange nut (3/8 inch)
Procedure
1. Install the left gusset with a bolt (3/8 x 1 inc h) and a flang e n ut (3/8 inc h) through the existing hole in the fix ed idler brac k et and frame ( Figure 2 ). Install 3 bolts (3/8 x 7/8 inc h) and 3 flang e n uts (3/8 inc h) in the holes drilled for the left gusset.
2. Install the right gusset with a 4 bolts (3/8 x 7/8 inc h) and 4 flang e n uts (3/8 inc h) through the existing hole in the frame .
2
Loading...
+ 2 hidden pages