Toro 107-9850 Installation Instructions
Form No. 3354-905 Rev A
Twin and Triple Bagger Mounting Kit
For 2004 and After Diesel-Powered and 2005 and
After Gas-Powered 500 Series Z Master
Model No. 107–9850
Installation Instructions
Note: Deter mine the left and right sides of the mac hine from the nor mal operating position.
Loose Parts
Use the chart below to verify that all parts have been shipped.
Step
Side plate
Spacer 2
1
2
3
Bolt, (3/8 x 1-1/2 inches)
Flange Nut, (3/8 inch)
Curved washer
Side plate
Spacer 2
Bolt, (3/8 x 1-1/2 inches)
Flange Nut, (3/8 inch)
Curved washer
Side plate
Spacer 2
Bolt, (3/8 x 1-1/2 inches)
Flange Nut, (3/8 inch)
Curved washer
Description
Qty.
1
8
8
8
1
8
8
8
1
8
8
8
Install the bagger side plates on a
Z500 with a Gas Engine.
Install the bagger side plates on a
Z593 with a Diesel Engine.
Install the bagger side plates on a
Z597 with a Diesel Engine.
Use
Step
1
Installing the Bagger Side
Plates on a Z500 with a Gas
Engine
Parts needed for this step:
1
Side plate
2 Spacer
8
Bolt, (3/8 x 1-1/2 inches)
8
Flange Nut, (3/8 inch)
8
Curved washer
Procedure
1. Use Figure 1 for the cor rect holes to use when
installing the side plate and R OPS .
© 2005—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
Figure 1
1. Side bracket (left side
shown)
2. Use these holes when
installing the side bracket
2. R emo v e the bolts , n uts , and w ashers holding
the roll bar to one side of the mac hine . Discard
the n uts , bolts , and w ashers ( Figure 2 ).
Register at www.Toro.com. Original Instructions (EN)
Printed in the USA.
All Rights Reserved
3. Install the bag g er side plate and the roll bar
section to the side of the mac hine using 4 bolts
(3/8 x 1-1/2 inc hes), 4 cur v ed w ashers (3/8
inc h), and 4 flang e n uts (3/8 inc h) ( Figure 2 ).
4. T or que the bolts and not the n ut, to 30 ft-lb
(40.7 N ⋅ m).
5. R e peat the ste ps abo v e for the opposite side
( Figure 2 ).
Note: Mak e sure the cur v ed w asher are
installed as sho wn in Figure 2 .
Figure 3
1. Bagger mounting bracket 5. Rear frame
2. Bolt, (3/8 x 1 inch)
3. Flange nut, (3/8 inch)
4. Curved washer, (3/8 inch)
6. Existing holes located here
7. Spacer
Figure 2
1. Bolt, (3/8 x 1-1/2 inches)
2. Curved washer, (3/8 inch)
3. Flange nut, (3/8 inch)
4. Side bracket
5. ROPS
6. W hen installing the bag g er mounting brac k et
to the side brac k ets use the spacer pro vided
in this kit ( Figure 3 ).
Step
2
Installing the Bagger Side
Plates on a Z593 with a
Diesel Engine
Parts needed for this step:
1
Side plate
2 Spacer
8
Bolt, (3/8 x 1-1/2 inches)
8
Flange Nut, (3/8 inch)
8
Curved washer
Procedure
1. Use Figure 4 for the cor rect holes to use when
installing the side plate and R OPS .
2
Loading...