Bagger Arm Kit for Use with ROPS
100 Series Z Master Mowers
200 Series Z Master Mowers
Part No. 106–5869
Part No. 106–5890
Loose Parts
Description Qty. Use
Form No. 3328–214
Installation Instructions
Bagger arm
Cable tie
Grip
Cotter pin
Cable—100 Series Baggers Only
Bolt, 5/16 x 1–1/4 inch
Washer, 11/32 inch
Install this kit when both a bagger and Roll Over Protection
System (ROPS) are used together.
Removing the Existing Bagger
Arm
1. Remove the shoulder bolt and cable from the bagger
arm (Fig. 1). Keep the shoulder bolt for use with new
bagger arm.
Note: Steps 2 and 3 are for 100 Series baggers only.
2. For 100 Series baggers only, remove the nut and pulley
from the bagger and remove the cable (Fig. 1). Save the
pulley and all hardware.
3. For 100 Series baggers only, remove the cable from the
bagger door hinge (Fig. 1). Save all hardware.
4. Loosen the setscrew holding the latch lever.
5. Cut the cable tie (Fig. 1).
6. Remove the grip from the bagger arm (Fig. 1).
1
2
1
1
1
4
4
Installing the bagger lever for 100 Series and
200 Series baggers
Installing the washers for a 100 Series ROPS
m–6136
1. Bagger arm
2. Cable
3. Shoulder bolt
4. Pulley and nut
5
Figure 1
2
4
7
8
5. Bagger door hinge
6. Cable tie
7. Latch lever
8. Grip
36
1
2002 by The Toro Company
8111 Lyndale Avenue South
Bloomington, MN 55420-1196
All Rights Reserved
Printed in the USA
1
7. Remove the cotter pin and washer from the bagger arm
(Fig. 2). Save the washer.
8. Slide the existing bagger arm out from the bagger and
save the washer (Fig. 2).
9. Remove the latch lever off of the bagger arm (Fig. 1).
3
4
1. Bagger arm
2. Latch lever
3. Grip
3
2
1
4
5
m–6207
Figure 3
4. Cable tie
5. Release lever cable
2
4
1
m–6206
Figure 2
1. Bagger arm
2. Bagger
3. Cotter pin
4. Washer
Installing the New Bagger Arm
on 100 and 200 Series Baggers
Note: Make sure the bagger is installed before installing the
handle.
1. Loosely install the latch lever onto the new handle
(Fig. 3).
2. Slide the grip on. Make sure the grip is totally on the
bagger lever (Fig. 3).
3. For 100 Series baggers, position the bagger arm inside
the right rear corner of the ROPS and under the cross
member (Fig. 4).
4. For 200 Series baggers, position the bagger arm outside
the right rear corner of the ROPS (Fig. 5).
5. Install an existing washer onto the bagger arm and
insert the arm into the bagger (Figure 4 or 5).
6. Secure the bagger arm with an existing washer and a
cotter pin (Figure 4 or 5).
2
m–6138
1. Bagger arm—100 Series
(Install inside ROPS)
2. Cotter pin
3. ROPS—100 Series
(Rollover Protection
System)
Figure 4
5
4. Bagger
5. Existing washer
4
2
4
3
2
1
5
3
5
1
m–6137
Figure 5
1. Bagger arm—200 Series
(Install outside ROPS)
2. Cotter pin
3. ROPS—200 Series
(Rollover Protection
System)
4. Bagger
5. Existing washer
Note: For 100 Series baggers, use the new cable included
in the kit. 200 Series baggers use the existing cable.
7. For 100 Series baggers, install the new cable to the
bagger door hinge (Fig. 6).
8. For 100 Series baggers, install the cable onto the pulley
and install to the bagger (Fig. 6).
9. For 100 and 200 Series baggers, install the bagger cable
to the bagger arm with the existing shoulder bolt
(Fig. 6).
3
5
2
84
7
5
3
6
7
4
1
6
2
4
7
3
9
1
1
m–6208
Figure 6
1. Bagger arm
2. Cable
3. Existing shoulder bolt
4. Pulley and nut
5. Bagger door hinge
6. Cable tie
7. Latch lever
8. Grip
9. ROPS (Rollover
Protection System)
Adjusting the Latch Lever
1. For a 100 Series bagger, position the latch lever
5 inches down from the top of the grip. See Figure 7.
2. For a 200 Series bagger, position the latch lever
6 inches down from the top of the grip. See Figure 7.
3. Tighten the setscrew that holds the latch lever.
4. Install the cable ties (Fig. 6).
m–6212
Figure 7
1. Bagger arm
2. Latch lever position—100
Series
3. Latch lever position—200
Series
4. Latch lever cable
5. 5 inches—100 Series
6. 6 inches—200 Series
7. Grip
Adjusting the Bagger Arm
Check the bagger arm and if needed, adjust it to remove
any slack.
1. Loosen the nuts on both sides of the stop bracket
(Fig. 8).
2. Adjust the stop bolt until there is no slack in the bagger
cable (Fig. 8).
3. Tighten the nuts on both sides of the stop bracket
(Fig. 8).
4
1
63
2
4
1
5
2
5
3
m–6209
Figure 8
1. Bagger arm
2. Stop bracket
3. Stop bolt
4. Bagger cable
5. Nut
Installing the Washers for a 100
Series ROPS
4
1
1. Existing flange nut,
5/16 inch
2. Bolt, 5/16 x 1–1/4 inch
3. Flat washer, 5/16 inch
4. Front floorpan
5
Figure 9
6
3
5. Support plate
6. ROPS—100 Series
(Rollover Protection
System)
2
m–6211
Install washers when a 100 Series bagger and ROPS are
used at the same time.
1. Remove the 4 bolts, washers and flange nuts that hold
the front floorpan and support plate to the front frame
(Fig. 9). Save the flange nuts.
2. For the top 2 holes, position 2 washers (11/32 inch)
between the ROPS and front floorpan for each hole
(Fig. 9).
3. Install the top 2 bolts (5/16 x 1–1/4 inch) through the
ROPS, washers and front floorpan (Fig. 9). Secure the
bolts with existing flange nuts.
4. Using the bottom holes that hold the front floorpan,
install the support plate and ROPS to the front of the
machine with 2 new bolts (5/16 x 1–1/4 inch) and 2
existing flange nuts (5/16 inch) (Fig. 9).
5
678
Loading...