Toro 104-8041 Installation Instructions
Light Kit
TimeCutter Z Riding Mower
Part No. 104-8041
Form No. 3326-115 Rev B
Installation Instructions
Attaching the Lights
1. To attach the side light, place the upper bracket on the
left-hand frame rail approximately 7/8 in. (22 mm) from
the deck mounting arm. Secure the lower bracket to the
upper bracket with a bolt (1/4 x 5/8 in.) and locknut
(Fig. 1).
2. Attach the light to the brackets with a hex. head screw
(5/16 x 1 in.), lock washer, and nut (Fig. 1).
Important Ensure that the side light does not interfere
with parking brake operation. The light is intended to be
aimed down toward the mower.
2
1
5
1. Light
2. Upper bracket
3. Lower bracket
4. Bolt, 1/4 x 5/8 in.
5. Locknut
3
Figure 1
8
4
6. Hex. head screw,
7. Lock washer
8. Nut
6
7
5/16 x 1 in.
m–5423
1
2
3
m–5428
Figure 2
1. Light and hex. head
screw
2. Lock washer
3. Nut
Installing the Switch
1. Lift the seat.
2. Remove the screws and washers securing the control
panel. Remove the panel.
3. Remove the plug in the control panel.
4. Slide the gasket around the bottom of the light switch
and insert the switch into the hole in the control panel
so that the rounded part of the switch is near the top of
the panel (Fig. 3).
1
3. Align the other two lights with the holes at the front of
the floor pan. Secure each light with a hex. head screw
(5/16 x 1 in.), lock washer, and nut (Fig. 2).
2001 by The Toro Company
8111 Lyndale Avenue South
Bloomington, MN 55420-1196
m–5424
Figure 3
1. Light switch
All Rights Reserved
Printed in the USA
1
5. Connect the light wire harness to the main wire harness
and to the light switch.
6. Route the wire harness through the hole in the side of
the control panel and attach the panel to the machine
using the screws and washers.
4. Pull the open connector up along the side of the front
console and attach it to the light on the left-hand side of
the machine. Ensure that the harness does not interfere
with the parking brake or motion control lever.
5. To secure the harness to the machine, push the harness
clips through the holes on the left side of the floor plate.
Installing the Wire Harness
1. Route the wire harness over the rear frame, through the
large hole in the rear panel, and behind the battery
(Fig. 4). Pull the harness to remove slack.
2. Secure the light wire harness to the main wire harness
with the 2 cable ties. Place one cable tie near the control
panel and one near the rear frame rail (Fig. 4).
1
2
Figure 4
1. Wire harness 2. Cable ties
m–5425
6. Route the harness over the front trunnion rod (Fig. 6)
and connect the wire harness to the front lights.
1
2
m–5426
Figure 6
1. Front trunnion rod 2. Wire harness
Installing the Fuse
1. Install the 10 amp. fuse into the fuse block in the slot
shown in Figure 7.
2. Lower the seat.
3. Route the harness through the hole in the left side panel.
Route it over the frame and deck lift shaft (Fig. 5) and
along the bottom of the left-hand frame rail.
1
2
m–5427
Figure 5
1. Wire harness 2. Deck lift shaft
1
m–5144
Figure 7
1. Install fuse here
2
Loading...