Toro 08703, 08705 Specifications

Sand Pro® 3040 & 5040

The Quick Attach SystemTM (QAS) and up to 24 attachments make the Sand Pro 3040 and 5040 the most versatile
vehicles in the bunker.

2015 Toro Commercial Equipment Guide 15-003-T Rev. 2/15

96

ENGINE

AIR CLEANER SYSTEM

FUEL CAPACITY

TRACTION DRIVE

GROUND SPEED

HYDRAULIC OIL

TIRES/WHEELS

MAIN FRAME

BRAKES

STEERING

CONTROLS/GAUGES

SEAT

ELECTRICAL

FEATURES

POWER

DIMENSIONS

GROUND CLEARANCE

WEIGHT

WARRANTY

Sand Pro® 3040 & 5040 Specifications

*

SAND PRO 3040, MODEL 08703 SAND PRO 5040, MODEL 08705

Vanguard®, V-twin cylinder, 4-cycle, OHV, air-cooled, gas engine with cast iron sleeves. 16 hp (11.9 kW) at
3600 rpm. Displacement: 29.3 cu. in. (480 cc). Oil capacity: 1.75 quart (1.8 liter). Electronic ignition. Full
pressure lubrication, oil filter. Base mounted engine and pump with 4 isolation mounts.

Remote mounted 3-phase Donaldson® air cleaner.

5.0 gallon (18.9 liter) of unleaded gasoline.

Direct driven hydrostatic variable displacement piston pump to 3 hydraulic motors for 3WD. Large, front mounted hydraulic cooler and fan. Foot pedal control,
forward/reverse. Patented Series/Parallel hydraulic traction system keeps three wheels working together, virtually eliminates spin-outs.

Infinitely variable 0-10 mph (16 km/h) forward; 4.3 mph (6.9 km/h) reverse.

5.0 gallon (18.9 liter) system capacity. Nylon reservoir to reduce corrosion. 10 (nominal) micron replaceable cartridge.

Three 22 x 11.00-8 pneumatic tubeless tires on demountable, interchangeable wheels. Tire pressure: 4-6 psi (27.5 kPa).

Tricycle vehicle with welded rectangular tubular steel frame construction. Rear engine placement.

Dynamic braking through the hydrostatic transmission and hand actuated brake lever.

Manual front wheel steering. 15" (38 cm) diameter steering wheel. Double lubed for life gearbox.

Hand operated choke, throttle, and hydraulic control for raising/lowering with float. Foot
pedal controls traction forward/reverse speed. Rear hydraulic lift and lower controls.Gauges:
hour meter.

High-back cushion seat w/drain hole. 4" front-back adjustment w/additional 1.75" mounting adjustment. (arm rests optional)

12-volt battery, 15 amp., 300 CCA @ 0° F, 12-volt electric starter. Dash mounted ignition
switch with key. Neutral interlock switch, seat switch. Also provisions for light kit.

97 dB(A) under normal operating conditions.

Width: 58" (147 cm), Length: 67.5" (171.5 cm), Height: 45.25" (114.9 cm), Wheelbase: 42.75" (108 cm)

6.0" (15.2 cm)

Net weight (less fluids): 930 lbs. (421.8 kg).

Two-year limited warranty. Refer to the Operator’s Manual for further details. Briggs & Stratton® provides a two-year commercial engine warranty and a lifetime Magnetron® warranty.

Vanguard®, V-twin cylinder, 4-cycle, OHV, air-cooled, gas engine with cast iron sleeves. 18 hp (13.4 kW) at
3600 rpm. Displacement: 34.8 cu. in. (570 cc). Oil capacity: 1.75 quart (1.8 liter). Electronic ignition. Full
pressure lubrication, oil filter. Base mounted engine and pump with 4 isolation mounts.

Hydraulic power steering. 15" (38 cm) diameter steering wheel.

Hand operated choke, throttle, and hydraulic control for raising/lowering with float. Foot pedal
controls traction forward/reverse speed. Front and rear hydraulic lift and lower controls. Gauges:
hour meter.

12-volt battery, 15 amp., 300 CCA @ 0° F, 12-volt electric starter. Fender mounted ignition switch
with key. Neutral interlock switch, seat switch, also provisions for light kit.

FRONT LIFT FRAME ASSEMBLY

HYDRAULIC FLEX BLADE

MANUAL BLADE

Front Quick Attach SystemTM mounting assembly and hydraulic components. Used on Sand Pro 5040 only. Model 08713.

Hydraulic QAS flex blade is designed for leveling, packing, and smoothing uneven areas in one pass. Model 08712.
Available for SP5040 only (requires Front Lift Frame Assembly – 08712)

Standard 40” (102 cm) width steel blade. Spring balanced manual blade is used for leveling uneven areas and pushing up bunkers after washouts (cannot be used
when 08712 is installed). Model 08714.

Blade extension available to increase blade width to 60” (152 cm) for leveling out larger uneven areas. PN 115-5646.

FRONT & REAR QAS ATTACHMENTS

BUNKER PUMP

BUNKER PUMP REMOTE

DISCHARGE KIT

LIP BROOM

TURF PLOW

Throws water up to 40’ (12 m) and can pump 95 gal/min (360 l/min). Adjustable throw direction and angle. Requires Rear Remote Hydraulics (08781) for rear QAS
mount. Requires Front Lift Frame Assembly (08712), Rear Remote Hydraulics (08781) and Front Remote Hydraulics for front QAS mount (on SP5040 only) Model 08765.

An available 50’ (15 m) discharge hose allows the QAS Bunker Pump to be removed and dropped into hard to reach areas.
PN 115-2084.

Eliminates the task of manually maintaining infield lips. Removes ridge buildup by sweeping material back into the infield. Mounts to front QAS (SP5040) and rear
QAS (SP3040 & 5040). Requires Front Lift Frame Assembly– 08712 for front attachment (on SP5040 only)

Lip Broom available from Rahn Industries at www.rahngroomer.com or 1-800-298-1707.

The 64” Turf Plow is a great tool for removing aeration cores from greens, clearing snow from walkways, cart paths and even sports fields. It is lightweight and
features a rounded lower lip that is gentle on turf. The Turf Plow fits both Sand Pro 3040 and 5040.

Turf Plow is available from Nordic Plow at nordicplow.com

MID-MOUNT ATTACHMENTS

MID-MOUNT ASSEMBLY
WEEDER TINE TOOLBAR

LEVELING BLADE

SOLID TINE TOOLBAR

CARBIDE TINE TOOLBAR

SPRING TINE TOOLBAR

* Specifications and design subject to change without notice. Products depicted in this literature are for demonstration purposes only.

Actual products offered for sale may vary in use, design, required attachments and safety features. See distributor for details on all warranties.

2015 Toro Commercial Equipment Guide 15-003-T Rev. 2/15

Base mounting assembly for mid-mount toolbars with spring-loaded regulation to allow relief if obstruction is hit. Model 08731.

Ideal for removing weeds and grass from less maintained bunkers and fields (requires Mid-Mount Assembly – 08731). Model 08732.

Attaches to any mid-mount toolbar to quickly level out large areas. Foot operated latch allows operator to lower leveling blade independently from the other mid­mount toolbar. PN 108-8496.

Used for general scarifying applications. Rotate teeth to maximize tine life (requires Mid-Mount Assembly – 08731). Model 08734.

Use in the harshest conditions and for extended life –15 carbide tines included (requires Mid-Mount Assembly – 08731). Model 08735.

Use for light to moderate scarifying and daily maintenance in bunkers and on premium fields (requires Mid-Mount Assembly – 08731). Model 08733.

Maintains the grass edge of the outfield near the infield skin or warning track. Easily renovate ballfields by removing overgrown turf and infield lip build-up.

EDGER

Significantly reduces labor required for infield edging (requires Rear Remote Hydraulics – 08781). Model 08766.

97

FRONT ATTACHMENTS

The Sand Pro 2020 is manufactured
in Tomah, WI ISO 9002 Certified Plant.