Toro 07297R, 7297 Installation Instructions

Form No. 3326-769 Rev B

Canopy Kit

Workman 1100/2100 and Twister Utility Vehicle

Model No. 07297 Model No. 07297R

Installation Instructions

Safety and Instruction Decals

Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost.

2. If your vehicle has a Roll Over Protection System

(ROPS), proceed to step 3. If your vehicle does not have a ROPS, proceed as follows:

A. Loosely attach the support brackets to the rear

support tube with 8 screws, 4 (5/16 x 2-3/4 in.) and 4 (5/16 x 1-3/4 in.); 16 flat washers (5/16 in.); and 8 flange nuts (5/16 in.) (Fig. 1).

B. Loosely attach the support brackets to the vehicle

with 8 screws (5/16 x 1 in.), 16 flat washers (5/16 in.), and 8 flange nuts (5/16 in.) (Fig. 1).

3. Remove the rear bolt that holds the front fender to the

dash and front frame support on each side of the vehicle. Do not remove the fenders from the vehicle (Fig. 1).

104-6731

Assembly

1. Position the machine on a level surface. Set the parking

brake, turn the ignition off, and remove the key.

Caution

If you leave the key in the ignition switch, someone could accidently start the engine and seriously injure you or other bystanders.

Remove the key from the ignition switch before you do any maintenance.

 2001 by The Toro Company 8111 Lyndale Avenue South Bloomington, MN 55420-1196

1. Rear support tube

2. Left-hand support bracket

3. Screw, 5/16 x 2-3/4 in., and washer, 5/16 in.

4. Screw, 5/16 x 1-3/4 in., and washer, 5/16 in.

5. Flange nut and washer, 5/16 in.

Figure 1

6. Screw, 5/16 x 1 in,. and washer, 5/16 in.

7. Left-hand front fender

8. Right-hand front support

9. Left-hand front support

Printed in the USA

4. Slide the slotted bracket on the front support between

the fender and vehicle. Loosely attach the front supports to the floor of the vehicle using the existing hardware on the vehicle (Fig. 1).

5. Secure the fenders with the bolts removed in step 3.

6. Loosely attach the canopy to the front supports using 4

long screws (5/16 x 2-3/4 in.), 8 flat washers (5/16 in.), and 4 flange nuts (5/16 in.) (Fig. 2).

Note: The canopy support is already loosely attached to the canopy (Fig. 2).

1. ROPS

2. Clinch nut

3. Canopy

Figure 3

Vehicle with ROPS

4. Screw, 3/8 x 1 in., and washer 3/8 in.

Figure 2

1. Canopy

2. Right-hand front support

3. Left-hand front support

4. Screw, 5/16 x 2-3/4 in., and washer, 5/16 in.

5. Flange nut and washer, 5/16 in.

6. Canopy support

7. If your vehicle has a ROPS, insert the clinch nuts into

the holes in the ROPS (Fig. 3). Lift the canopy and attach it to the ROPS with 2 screws (3/8 x 1 in.) and 2 flat washers (3/8 in.) (Fig. 3). If your vehicle does not have a ROPS, lift the canopy assembly and attach it to the rear support tube with 2 screws (5/16 x 2 in.), 4 washers (5/16 in.), and 2 flange nuts (5/16 in.) (Fig. 4).

Figure 4

Vehicle without ROPS

1. Rear support tube

2. Canopy

3. Screw, 5/16 x 2 in., and washer, 5/16 in.

4. Flange nut and washer, 5/16 in.

8. Starting at the bottom of the vehicle and working your

way to the top, tighten all of the fasteners.

9. Adjust the front suspension; refer to Adjusting the Front

Suspension in the vehicle Operator’s Manual.