Toro 03910 Specifications

Reelmaster® 3550-D

The Toro® Reelmaster® 3550-D floats effortlessly over contours in fairways and green surrounds. With a productive
82-inch cutting width, turf-friendly tires, the superior traction of a Series/Parallel 3-wheel drive system, and a weight
of less than 2,000 pounds,* the Reelmaster 3550-D is engineered to make a big impression...without leaving one.

* Gross vehicle weight for standard configuration, including five 18-inch cutting units, with no optional accessories.

2015 Toro Commercial Equipment Guide 15-003-T Rev. 2/15

62

ENGINE

LUBRICATION

FUEL FILTER

COOLING

FUEL TANK CAPACITY

TRACTION DRIVE

GROUND SPEED

TIRES

MAIN FRAME

BRAKES

STEERING

GAUGES

CONTROLS

ELECTRICAL & INTERLOCKS

REEL DRIVE

SEAT

DIMENSIONS

WEIGHT

SAFETY

CERTIFICATION

WARRANTY

Reelmaster® 3550-D Specifications

*

REELMASTER 3550-D, MODEL 03910

Kubota® 3-cylinder, liquid-cooled diesel engine. 24.8 hp (18.5 kW) @ 3000 RPM. Engine governed to 3220 RPM high idle (± 50 RPM), 1400 RPM low idle
(± 50 RPM). Displacement: 68.5 cu.in. (1123 cc). Peak torque: 57.2 lbs-ft @ 2200 RPM.

Pressurized lubrication system with 3.5 quarts (3.3 liters) capacity.

10 micron spin-on filter with integral water separator.

Aluminum side-by-side oil cooler/radiator. 8.5 fins per inch, wavy fin, non-louvered. 5.25 quart (4.9 liter) capacity.

7.5 gallons (28.3 liters), diesel fuel. Biodiesel-Ready for use up to B-20 (20% biodiesel and 80% petroleum blend).

Series/Parallel hydraulic traction circuit provides continuous 3-wheel drive, in mow and transport. Hydrostatic traction drive provides infinitely variable speed in
forward and reverse. 6 gallon (23 liter) hydraulic system capacity.

0-10 mph (0-16.1 km/hr) forward transport; 0-7mph (0-11.3 km/hr) mow; 0-3.5 mph (5.6 km/hr) reverse.

Three (3) 22x12-12, 4-ply, no tread tires. 12 PSI recommended pressure.

Formed steel, welded steel and steel tubing.

Hydrostatic service brake. Hand-operated parking brake.

Power steering with tilt steering wheel.

Hour meter, fuel gauge, diagnostic lamp, cluster gauge with glow plug and charge indicator lights, and low engine oil pressure and high coolant temperature warning
lights (high temperature safety shut off).

Foot operated controls: Forward and reverse traction pedal, mow/transport speed limiter. Hand operated on control panel: Parking brake lever, ignition switch,
engine throttle lever, work light switch, on/off switch for cutting units, joystick for cutting unit lift and lower. Other controls: Steering wheel tilt control, reel speed
control, backlap engagement lever.

Heavy-duty 12 V battery, 570 CCA; 40 amp alternator/regulator. Electronic control unit is microprocessor based, solid state control unit with diagnostic capabilities.
Traction pedal neutral, parking brake, operator presence in seat, and cutting unit engage/disengage safety interlock switches.

Hydraulic, open loop through oil cooler & filter. High efficiency pressure balanced gear type motors and pumps.

Mechanical suspension standard.

Height: 74" (188 cm) Length: 110” (279.4 cm) Wheelbase: 59.5” (151.1 cm) Operational Width: 94” (238.8 cm) Transport Width: 91” (213.1 cm)

1,985 lbs. (900.38 kg) with (5) 18" 8-blade cutting units.

ROPS Standard. Capable of traversing a 25° slope in any direction on dry grass, while mowing.

Complies with ANSI B71.4-2012 and CE requirements. EN ISO 5395.

Two-year limited warranty. Refer to the Operator’s Manual for further details.

* Specifications and design subject to change without notice. Products depicted in this literature are for demonstration purposes only.

Actual products offered for sale may vary in use, design, required attachments and safety features. See distributor for details on all warranties.

2015 Toro Commercial Equipment Guide 15-003-T Rev. 2/15

63

The Reelmaster 3550-D is manufactured
in Tomah, WI ISO 9002 Certified Plant.