Tornador Black Z-020S Instruction Manual

Vers.2016/02 1

Z-020S Tornador-Gun (Tornador-Black)

Original-Bedienungsanleitung / Original Instruction Manual

Beispielhafte Abbildung / Exemplary image

BENDEL Werkzeuge GmbH & Co.KG

Wilhelm-Schulze-Str-8-10 ° D-29549 Bad Bevensen

Vers.2016/02 9

Read and understand these instructions before operating the tool.

General safety instructions and individual safeness

Attention

• You need to read, understand and follow the complete instruction manual and the safety
briefing BEFORE USE. Afterwards the instruction needs to be kept at a adequate place,
accessible for any user.

• The unit may only be used, cleaned and maintained by persons who understand and follow
this instruction. The operator must be in physically condition to utilize the tool.

• Improper use or unauthorized modification will cause serious health damage by yourself,
somebody else or animals and other property.

• Individual safety instructions from the related countries needs to be observed additional.

• Make sure that the tool is out of range for children or other persons who are not familiar with

the handling of the unit. Switching on the device by such persons is dangerous.

Workplace hazards:

• Slipping, stumbling or collapsing are the main reasons for serious or deadly accidents. Take care

for hoses which maybe are in the near operating area.

• Maintain a balanced body position and secure footing.

• Cyclic courses of movements, inappropriate posture and constant vibrations will cause fatigue to

arms, hands and body.

• High sound levels can lead to permanent hearing loss. Use hearing protection as recommended.

• Avoid breathing in dust or handling debris from work process which can be harmful to your health.

• This tool may only be used and maintained by qualified people who are in the constitutional

position to handle the dimension, weight and force of the device.

• This tool is not intended for use in explosive atmospheres and is not insulated for contact with

electrical power sources.

• Please consider that the material your tool is made of always can have material tiredness.

Projectile hazards:

• Even small projectiles, for example swirled by the outlet air of your tool, can injure eyes and lead

to blindness.

• Always wear impact-resistant eye and face protection when involved with or near the operation,

repair or maintenance of the tool or changing accessories on the tool.

• Also take care that people surrounding you will follow the instruction to wear impact-resistant eye

goggles and face masks.

• In case of a male function switch off the device immediately and provide the tool to a authorized

service station to check.

• If you recognize high unusual vibration switch of the unit and look for the reasons. Do not switch

on again until before the problem is solved.

Individual safeness

• Only use the tool in well-rested conditions.

• Always take care what you are doing and use your commonsense.

• Do not use the tool when you are tired or under the influence of medicine, alcohol or drugs. Any

carelessness will cause serious hurts.

• Always wear adequate protective clothing and eye protection. Further protection like dust masks,

helmets, ear protection, work gloves or nonskid safety shoes may be required. Pls. refer to the
pictograms in this manual. Even if these clothing’s are not especially required we highly
recommend to use them as the risk of injury will decrease formidable.

• Always disconnect the device from air supply when not in use, before changing accessories or

maintenance to avoid starting the tool by mistake.

• Always check the unit, hoses and fittings for damages or loose before use.

• Make sure that any spanners or other parts you have used with the tool will be removed before

Vers.2016/02 10

operating.

• Do not super extend and take care on a balanced position and secure footing to control the tool

also in unexpected situations.

• Long hairs and loose clothing could tangled up in rotating parts of the device and cause serious

hurts.

Exemplary drawing.

Air supply requirements

• Supply tool with a maximum pressure according to the technical data of this unit of clean, dry air.

Higher pressure drastically reduces tool life and/or can cause several injury.

• Connect tool to air line using pipe, hose and fitting sizes shown in the diagram above.

• Do not install a quick coupler directly into the air tool handle.

• In order to have the tool working to full satisfaction the minimum air delivery must be at least 10%

higher than the indicated air consumption of the air tool.

• Please consult the technical data in this instruction manual.

Pneumatic tool and safety instructions

• The goal of Bendel Werkzeuge is to offer tools that help your work safely and efficiently.

• The most important safety device for this or any tool is YOURSELF.

• Your care and good judgment are the best protection against injury. All possible hazards cannot

be considered here, but we have tried to highlight some of the most important ones.

• This tool may only used by qualified people.

• This tool and its accessories must not be modified.

• Do not lay down the device before all the rotary parts stopped.

• Do not keep the air tool running while carrying it.

• Maintain a firm grip on the power tool and position your body and arm to allow you to resist

kickback forces. Always use auxiliary handle, if provided, for maximum control over kickback or
torque reaction during start-up. The operator can control torque reactions or kickback forces, if
proper precautions are taken.

• Never place your hand near the rotating accessory. Accessory may kickback over your hand.

• Switch off the unit immediately in case of blocking or twist. Disconnect the air supply and do not

switch on again until the problem is solved. Understand the reason why the tool has been blocked
and make sure that this situation will not occur once more by counteract accordingly.

Air supply and connection hazards:

• Air under pressure can cause several injury !

• Always shut off air supply, drain hose of air pressure and disconnect tool from air supply, when

not in use, before changing accessories or maintenance.

• Never put direct air at yourself or anyone else.

• Whipping hoses can cause serious injury. Always check for damaged or loose hoses and fittings.

• Do not exceed maximum air pressure according on the name plate respectively 8.5 bar.

• Do not use quick disconnect couplings directly at the tool. See instructions for correct set-up !