Tornado PS Series 98220, PS Series 98221, PS Series 64230 Operation & Maintenance Manual

[phone] FAX [phone]

ââââ

Tornado

Operation & Maintenance Manual

For Commercial Use Only

TORNADO INDUSTRIES

7401 W. LAWRENCE AVENUE

CHICAGO, IL 60706

www.tornadovac.com

The PS Series of Carpet Spotters (Series F)

64220 & 98220 (115v, 60Hz)

L2700FG 9/01 ã2001 Tornado Industries All rights reserved.

Catalog No.

98221 (230v, 50HZ)

NOTES

2

This instruction book covers:

CATALOG NO.
SERIES
PUMP
VACUUM

CAPACITY
VOLTS
AMPS
CERTIFICATION

98220 98221 64230

FF F

55 PSI 55 PSI 55 PSI

94 CFM

2

84”H

O

82 CFM

68”H2O

94 CFM

84”H2O

2 Gal 2 Gal (7.6l) 2 Gal

115V 230V 115V

84 8

**

*

*This product conforms to ANSI/UL Standard 561

and is certified to CAN/CSA Standard C22.2 No. 10.

ALL SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.

3

TABLE OF CONTENTS:

Safety Instructions 5
Electrical/Grounding Methods 7
Unpacking Precautions 9
General Precautions 11
Preparation Instructions 12
Operating Instructions & Cleaning Tips 13
Maintenance Instructions 15
Main Assembly 16
Optional Handle Assembly 18
Vacuum/Pressure Hose Assembly 19
Wiring Diagram (115V) & Accessories 20
Wiring Diagram (230V) 21

Tornado® Standard Warranty Program*

10 Years:

Warranties do not cover
components subject to normal
wear or abuse and misuse, and
have other limitations not
specified here. For full details ,
contact your Authorized Tornado
Distributor, Service Center, or the
Tornado Technical Service
Department.

Parts on all Tornado and Tornado/Karcher

All plastic tanks and

rotationally-molded bodies

2 Years:

cleaning equipment

1) 2)

1 Year:

Labor on all Tornado and Tornado/Karcher

cleaning equipment

1) 2)

1 Year:

Warranty on batteries, one full year,

Not pro-rated.

* Effective January 1st, 2001. Terms subject to change without notice.

1) Windshear™ Blower-Dryer, Insulation Blowers, CW 50, CW 100, and Duo-Upright
Carpetkeepers™ are warranted for 1 (one) year for parts and labor.

2) Warranties on the ICC1, KMR 1200, KMR 1250, and KMR 1700 are 24 months parts/6 months
labor OR 1000 hours of operation, whichever comes first. Warranties on the BR and BD 1000
are 24 months parts/12 months labor OR 1000 hours of operation, whichever comes first.

4

IMPORTANT SAFETY INSTRUCTIONS

WHEN USING AN ELECTRICAL APPLIANCE, BASIC PRE­CAUTIONS SHOULD ALWAYS BE FOLLOWED INCLUDING THE
FOLLOWING: READ ALL INSTRUCTIONS BEFORE USING THIS
MACHINE.

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY:

1. Do not leave machine unattended when plugged in. Unplug from outlet

when not in use and before servicing.

2. Use indoors only. Do not use outdoors and do not expose to rain.

3. Do not allow to be used as a toy. Close attention is

4. necessary when used by or near children.

5. Use only as described in this manual. Use only manufacturer’s

recommended attachments.

6. Do not use with damaged cord or plug. If machine is not working as it

should, has been dropped, damaged, left outdoors, or dropped into
water, return it to a service center.

7. Do not pull or carry by cord, use cord as a handle, close a door on

cord, or pull cord around sharp edges or corners. Do not run machine
over cord. Keep cord away from heated surfaces.

8. Do not unplug by pulling on cord. To unplug, grasp the plug not the

cord.

9. Do not handle plug or machine with wet hands. Do not put any object

into openings. Do not use with any opening blocked; keep free of dust,
lint, hair, and anything that may reduce air flow.

10. Keep hair, loose clothing, fingers, and all parts of body away from

openings and moving parts.

11. Turn off all controls before unplugging.

12. Use extra care when cleaning on stairs.

13. Do not use to pick up flammable or combustible liquids, such as

gasoline, or use in areas where they may be present.

14. Connect to a properly grounded outlet only. See Grounding

Instructions.

SAVE THESE INSTRUCTIONS

5

IMPORTANTES MESURES DE SÉCURITÉ

L’UTILISATION D’UN APPAREIL ÉLECTRIQUE DEMANDE CERTAINES

PRÉCAUTIONS: LIRE TOUTES LES INSTRUCTIONS AVANT DE FAIRE

FONCTIONNER CET APPAREIL.

AVERTISSEMENT. POUR RÉDUIRE LES RISQUES D’INCENDIE, DE CHOC

ÉLECTRIQUE OU DE BLESSURE:

1. Ne pas laisser l’appareil sans surveillance lorsqui’il est branché.
Débrancher lorsque l’appareil n’est pas utilisé et avant l’entretien.

2. Ne pas utiliser à l’extérieur et ne pas aspirer de matières humides.

3. Ne pas permettre aux enfantes de jouer avec l’appareil. Une attention
particulière est nécessaire lorsque l’appareil est utilisé par des enfantes
ou à proximité de ces derniers.

4. N’utiliser que conformément à cette notice avec les accessoires
recommandés par le fabricant.

5. Ne pas utiliser si le cordon ou la fiche est endommagé. Retourner l’appareil
à un atelier de réparation s’il ne fonctionne pas bien, s’il est tombé ou s’il a
été endommagé, oublié à l’extérieur ou immergé.

6. Ne pas tirer soulever ni traîner l’appareil par le cordon. Ne pas utiliser le
cordon comme une poignée, le coincer dans l’embrasure d’une porte ou
l’appuyer contre des arétes vives ou des coins. Ne pas faire rouler
l’appareil sur le cordon. Garder le cordon à l’écart des surfaes chaudes.

7. Ne pas débrancher en tirant sur le cordon. Tirer plutôt la fiche.

2. Ne pas toucher la fiche ni l’appareil lorsque vos mains sont humides.

3. N’insérer aucun objet dans les ouvertures. Ne pas utiliser l’appareil

lorsqu’une ouverture est bloquée. S’assurer que de la poussière, de la
peluche, des cheveux ou d’autres matières ne réduisent pas le débit d’air.

4. Maintenir les cheveux, les vétements amples, les doigts et toutes les parties

du corps à l’écart des ouvertures et des pièces mobiles.

5. Mettre toues les commandes à la position ARRÊT avant de débrancher

l’appareil.

6. User de prudence lors du nettoyage des escaliers.

7. Ne pas aspirer des liquides inflammables ou

combustibles, comme de l’essence, et ne pas faire fonctionner dans des
endroits où peuvent se trouver de tels liquides.

14 Ne brancher qu’à une prise de courant avec mise à la

terre. Voir les instructions visant la mise à la terre.

INSTRUCTIONS VISANT LA MISE À LA TERRE

6

GROUNDING INSTRUCTIONS

This appliance must be grounded. If it should malfunction or breakdown,
grounding provides a path of least resistance for electric current to reduce
the risk electric shock. This machine is equipped with a cord having an
equipment -grounding conductor and grounding plug. The plug must be
inserted into an appropriate outlet that is properly installed and grounded in
accordance with all local codes and ordinances.

WARNING: Improper connection of the equipment-grounding
conductor can result in a risk of electric shock. Check with a qualified
electrician or service person if you are in doubt as to whether the
outlet is properly grounded. Do not modify the plug provided with the
appliance - if it will not fit the outlet, have a proper outlet installed by a
qualified electrician.

This appliance is for use on a nominal 120-volt circuit, and has a
grounding plug that looks like the plug illustrated in sketch A. A temporary
adapter that looks like the adapter illustrated in sketches B and C may be
used to connect this plug to a 2-pole receptacle as shown in sketch B if a
properly grounded outlet is not available. The temporary adapter should be
used only until a properly grounded outlet (sketch A) can be installed by a
qualified electrician. The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent ground such as a
properly grounded outlet box cover. Whenever the adapter is used, it must
be held in place by a metal screw.

NOTE: In Canada, the use of a temporary adapter is not permitted by

the Canadian Electrical Code

SKETCH A SKETCH B SKETCH C

7

INSTRUCTIONS VISANT LA MISE À LA TERRE

Cet appareil doit etre mis à la terre. En cas de défaillance ou de panne, la
mise à la terre fournit au courant un chemin de moindre résistance qui
réduit le risque de choc électrique. Cet appareil est pourvu d’un cordon
muni d’un conducteur de terre et d’une fiche avec broche de terre. La
fiche doit étre branchée dans une prise appropriée correctement installée
et mise à la terre conformément aux réglements et ordonnances
municipaux.

AVERTISSEMENT. Un conducteur de terre mal raccordé peut
entraîner un risque de choc électrique. Consulter un électricien ou
un technicien d’entretien qualifié si vous n’étes pas certain que la
prise est correctement mise à la terre. Ne pas modifier la fiche
fournie avec l’appareil - si elle ne peut étre insérée dans la prise, faire
installer une prise adéquate par une électricien qualifié.

CROQUIS A CROQUIS B CROQUIS C

Cet appareil est destiné à un circuit de 120 V et est muni d’une fiche de
terre semblable à celle illustrée par le croquis A. Un adaptateur temporaire
semblable à celui illustré par les croquis B peut étre utilisé pour brancher
cette fiche à une prise bipolaire comme l’illustre le croquis B si une prise
avec mise à la terre n’est pas disponible. L’adaptateur temporaire devrait
étre utilisé seulement jusqu’à ce qu’une prise avec mise à la terre soit
installée par un électricien qualifié. L’oreille rigide ou le crochet ou autre
dispositif semblable, de couleur verte, prolongeant l’adaptateur doit étre
raccordé à un élément correctement mis à la terre comme le couvercle
d’une boîte de sortie mise à la terre. L’adaptateur doit étre fixé par une vis
métallique.

NOTE: Au Canada, l’utilisation d’un adaptateur temporaire n’est pas
autorisee par le Code canadien de l’électricité.

8

WHEN THE MACHINE IS DELIVERED

Check the carton carefully for signs of rough handling. Remove the
machine from the carton and look for concealed damage. If the machine is
damaged, notify the carrier immediately and request an inspection. Be
sure to keep the carton, packing inserts, packing lists and carrier’s receipt
until the inspector has verified your claim.

BEFORE OPERATING THE MACHINE

Read the manual carefully and completely before attempting to operate the
unit. This manual has important information for the use and safe operation
of the machine. Keep this manual on file and handy. This machine will
assure years of satisfactory service if operated and maintained according
to recommendations in the manual. If additional information is needed,
please contact your local distributor or write to:

TORNADO INDUSTRIES

7401 W. LAWRENCE AVE.

CHICAGO, IL 60706

708/867-5100

FAX: [phone]

All information and specifications printed in the manual and parts list are
current at the time of printing. However because of Tornado’s policy of
continual product improvement, we reserve the right to make changes at
any time without notice.

This machine was shipped with window washer antifreeze, during the
winter months, in the solution line system to protect the pump and valves
from freezing during transportation and storage. Before you use the unit,
rinse the solution line system with clean water (refer to Protect From
Freezing).

9

WARRANTY

To protect your investment, promptly fill out the

required information on the warranty card that

comes with the unit and mail it back to

Tornado Industries

Note: Service repair and warranty work

is not normally handled at the factory.

WARNING

The machine was designed for use in spot
cleaning on carpeted floors and for upholstery
extraction applications as per instructions and
recommendations written in this manual. Any
deviation from its proper use or purpose and the
consequential damage that may occur is the sole
responsibility of the end user.

10

GENERAL PRECAUTIONS

• Do not use the machine for dry vacuuming. This machine is not fitted

with a dry filter.

• Use defoamer in the recovery tank at all times to prevent damage to the

vacuum motor.

• Do not use water in excess of 140 degrees F (60 degrees C).

• Use only low foaming carpet and upholstery cleaners and defoamers

intended for machines of this type. Do not use dyes, bleaches,
ammonia or other additives. The use of powdered cleaning solution if
not diluted properly may result in the intake screen clogging or damage
to the pump.

• Do not expose machine to freezing temperatures.

• Do not attempt to repair warranted machines. All repairs must be done

by a qualified and authorized repair center. Non warranted repairs will
be billed back to the owner of the unit.

• Do not use any replacement parts except those specified in the parts

list. Unauthorized parts will void the warranty and could cause the unit
not to function properly.

REQUIRED CLEANING CHEMICALS

Use only low foam cleaning chemicals that are designed for carpet and
upholstery extraction.

• General carpet and upholstery extraction cleaner added to the solution

tank.

• Traffic lane pre-spray usually applied with a hand or pump-up sprayer.

• Spotter used with a hand sprayer.

• Defoamer only goes into the recovery tank.

CAUTION: Use as directed. Do not over-use the cleaning chemicals.

EXTENSION CORD

If an extension cord is used, the wire size must be a least one size larger
than the power cord on the machine. The ProSpot is equipped with a 25’
18-3 power cord.

FAILURE TO COMPLY WITH THE ABOVE WARNING INSTRUCTIONS
WILL VOID THE WARRANTY.

11

PREPARING THE MACHINE:

WARNING!! To prevent possible disease hazard, before

attempting to clean bodily fluid spills, you must kill any
viruses, germs or bacteria present in the bodily fluid.

1. Loosen the two latches that hold the recovery tank to the solution tank.

Lift the recovery tank off.

2. Pour up to 2 gallons (7.6 liters) of hot water into clean solution tank.

Water temperature must not exceed 140°F (60°C). Pour in a non­foaming cleaning concentrate to the proper dilution noted on the
container. Be sure that the vacuum motor foam filter is in place

(located on top of the solution tank).

3. Place the recovery tank on the solution tank and refasten the tank

latches. Attach hand tool to solution and vacuum hoses. Attach solution
hose to fitting on front of solution tank (98225 & 98226 only). Be sure
hose coupler locks onto extractor’s coupler. Connect vacuum hose to
recovery tank.

4. Plug power cord into a grounded outlet. See GROUNDING

INSTRUCTIONS.

5. See “Illustrated Parts List and Wiring Diagram” for available
accessories.

12

OPERATING THE PROSPOT:

1. Turn the switch, located on the rear panel, to “VACUUM/SPRAY”.

2. Place the hand tool on the surface to be cleaned and squeeze the
solution lever. Move tool over surface to be cleaned. Note: Do not apply
too much solution to upholstery to minimize dry time.

3. Always monitor recovered solution in the recovery tank. Excess water

can be drawn into the vacuum motor resulting in damage to the motor.
Turn machine off and empty recovery tank periodically. This machine is
equipped with a float shut off to help prevent damage to the vacuum
motor.

4. At the end of job turn switch to ‘OFF’ and disconnect power cord from

outlet. Empty recovery tank (turn upside down and empty through hose
intake) and solution tank of any solutions. Thoroughly rinse both tanks
to remove any residue and to keep tanks fresh.

CLEANING TIPS:

• Check the condition of the carpeting. If the carpet is loose, heavily
soiled, stained, spotted or badly worn, point this out to the person in
charge.

• Locate an inconspicuous spot on the area to be cleaned. Test carpet for
colorfastness before proceeding. Pour the concentrated cleaning
solution on the spot, cover with a white towel and place a heavy object
on top to absorb the cleaning solution. Wait 10 minutes for any reaction
to take place. Remove weight. If there is no color transfer, it should be
safe to clean.

• Clean the area first with a Clean-Air Carpetkeeper, upright vacuum. Do
not use the ProSpot as a dry vacuum! Heavily soiled carpet or areas of
concentrated foot traffic should be treated with

• recommended pre-spotting or pre-spray chemicals, using a hand spray
trigger bottle or pump up sprayer. Do not allow any spotter or pre-spray
to dry on the carpet. Use a small hand held carpet brush to agitate the
carpeting. Always agitate toward the center of the spot.

• After spot cleaning the carpet, place a small square of aluminum foil or
6 mil poly square under the furniture legs to prevent moisture from

13

damaging the finish or rusting the metal glides, if placing furniture on
moist carpeting.

• Identify the type of carpet fiber to be cleaned. Most carpet fibers in use

are nylon or acrylic based. Best results in cleaning would be obtained if
hot water is used to clean these types of fibers. On the other hand, hot
water could shrink natural fiber carpeting, like wool and cotton in
particular. Exercise caution when cleaning natural fibers. Use cool water
test for colorfastness and apply the least amount of cleaning solution as
possible.

• Furnishings have many different types of fabric. Be sure that the proper
chemicals are used and that you follow the chemical manufacturer’s
directions.

• When the ProSpot runs out of cleaning solution, noted by streaking or
no solution flow, turn off the machine and drain the recovery tank. Refill
solution tank and continue cleaning.

• To decrease drying time go over the carpet and/or furnishings without
squeezing the spray lever or turn the power switch to “VACUUM ONLY”.
To further decrease the drying time, use the Windshear 3000 Carpet
Blower.

PROTECT FROM FREEZING

If it becomes necessary to store in temperatures that could drop below 40
degrees F, the pumping system, hoses and valves must be protected from
freezing with a methyl hydrate window washer antifreeze solution. Do not
use ethylene glycol or cooling system antifreezes.

• Add one quart of windows washer antifreeze to the solution tank, turn
on the pump and squeeze the spray lever until antifreeze solution fills
the solution lines.

• Always allow the unit to reach room temperature before turning on to
remove the antifreeze from the system.

14

MAINTENANCE:

WARNING!! Always unplug power cord before cleaning,
making adjustments or repairs.

AFTER EACH USE:

• Thoroughly flush out both tanks. HINT: To clean the recovery tank turn
upside down and lightly spray into the vacuum intake. this will
“backflush” the filter screen and float shut-off ball. Drain tank through
the hose intake.

• Wipe down entire unit with cleaning solution.

• Flush pump system with 1 quart clean water with 1 ounce white vinegar.

• Remove and clean foam vacuum filter. Remove lint from vacuum motor

intake screen. Store with tanks exposed in clean dry place.

• Inspect power cord for damage. Replace if necessary. Wipe and coil the
cord from machine to the plug then place coiled cord through molded
handle for storage or transport.

• Remove lint from hand tool opening. HINT: Back-flush through vacuum
hose end.

PERIODIC MAINTENANCE

• It is highly recommended that once a month you flush the ProSpot out
with a 8 to 1 ratio of water to white vinegar or anti-browning solution
through the extractor. This will help to prevent the build up of alkaline
residue.

• If the spray jet becomes clogged, remove and wash it thoroughly and
blow dry. Do not use wire or pins to clean the nozzle as this will cause
the spray pattern to become distorted, thereby giving you a streaking
pattern on the carpeting.

• Once a month, inspect all electrical cables, hoses, filters and
connections in the ProSpot. If you see something that should be
repaired or replaced this should be reported and repaired. Little things
are easy to forget, but as these little things add up you end up with a
cluster of problems that will cost you more in the long run.

• Inspect the vacuum motor carbon brushes after every 700 hours of use
replace, if necessary.

• Be sure to use genuine Tornado parts and that service is provided by an

authorized Tornado Service Center. 1-800-VACUUMS Use of non-OEM
parts will void the warranty.

15

ES SERIES CARPET SPOTTERS

64230, 98220 & 98221

MAIN ASSEMBLY

ITEM NO. DESCRIPTION PART NO. QTY.

1 SCREW-SLOTTED ROUND HEAD MACHINE #8-32 x ¾ 00600 2
2 WASHER-LOCK (H/S) #10 01713 1
3 NUT-HEX LOCK (KEPS) #8-32 02956 2
4 SCREW-PHILLIPS PAN HD. MACH. # 8-32 X 3/8" 02995 4
5 WASHER – SEALING ¼ 07741 2
6 NUT-HEX.LOCK(KEPS) #10-24 10892 6
7 WASHER-PLAIN 1/2" 12957 1

12

(12)

10 FITTING-BRASS ELBOW(45D) 1/4"FPT X 1/4"MPT 15075 2
11 FITTING-BRASS ELBOW 1/4"MPT X 3/8"HB 15223 1
13 SCREW - PHILLIPS TRUSS HD. MACH. #10-24 X 1/2" (SS) 17848 11
14 WASHER-PLAIN #10 (SS) 17850 8
15 WASHER-PLAIN 5/16" (SS) 19191 4
16 SCREW-PHILLIPS FLAT HD. MACH. # 8-32 X 1/2" (BLK.ZINC) 19255 2
17

(17)

18

(18)

49

(49)

19 LATCH-DRAW W/ KEEPER 19504 2
20 WHEEL- 6" DIA. X 1-1/4" (BLACK W/ BLK HUB) 19505 2
21 SPACER-5/16" DIA. 19506 2
22 NUT-HEX.LOCK (NYL.INS.) 5/16-18 19513 2
23 ASSEMBLY-VACUUM STACK/FLOAT CAGE 19516 1
24 SCREEN-VAC.MOTOR INTAKE 19517 1
25 FILTER-VAC.MOTOR INTAKE (FOAM) 19520 1
26 PIPE-NIPPLE, PVC 1/4"MPT X 4" LG. 19522 1
27 FITTING-BRASS ADAPTOR 1/4"FPT X 1/4" HB 19523 2
28 FITTING-NYLON ELBOW 1/8"MPT X 1/4"HB 19524 2
29 FILTER-SOL. SCREEN 19525 1
30 HOSE-SOLUTION (SCREEN) 19528 1
31 WASHER-LOCK (I/T) # 8 19530 4
32 SCREW-PHILLIPS PAN HD. MACH. 5/16-18 X 2-1/2" (SS) 19532 2
33 LABEL-"WARNING!TO REDUCE THE RISK OF ELECTRIC..." 19533 1
50 BRACKET-PUMP MTG(RUBBER) 31490 2
34 SCREW-PAN HEAD #10-16 X 1/2" LG. 19565 4
35 GASKET-SOLUTION TANK 19610 1
36 LABEL-"VACUUM ONLY-OFF-VACUUM/SPRAY"SWITCH(PS) 19611 1
37 WASHER-PLAIN 1/2" (SS) 19616 3
38 SHROUD, VAC MOTOR 19937 1
39 WASHER - LOCK E/T #10 30019 6
40 GASKET-VAC. MOTOR BOTTOM 30456 1
41 GASKET, MOTOR TOP 30457 1
42 SWITCH-ROCKER, DPDT (3 POS.) 15A 30472 1
43 BRACKET-VAC. MOTOR MT'G 30475 2
48 BRACKET-PUMP MT'G 31471 1
44 SCREW-PHILLIPS PAN HEAD MACHINE # I0-24 x 3/8 30678 10
45 DECAL-"TORNADO" 30814 1
47
51
46

(46)
* = NOT SHOWN
( ) = ITEMS TO BE USED WHERE APPLICABLE

MOTOR-VACUUM,115V/50-60HZ (98220 & 64230 ONLY)
MOTOR-VACUUM,230V/50-60HZ (98221 ONLY)

8 FITTING-BRASS NIPPLE 1/4"FPT X 1/4"Q.C. 14881 1
9 CLAMP-HOSE(CRIMP TYPE) .433"-.512"(2-EAR) 15065 4

TANK-SOLUTION (98220 & 98221 ONLY)
TANK-SOLUTION (64230 ONLY)
TANK-RECOVERY (98220 & 98221 ONLY)
TANK-RECOVERY (64230 ONLY)
PUMP- 55 PSI/115VAC - (64230 & 98220 ONLY)
PUMP- 55 PSI/230VAC - (98221 ONLY)

LINE FILTER 31067 1
HOSE-SOLUTION (PUMP) 19527 2
ASS'Y POWER CORD 115V (64230 & 98220 ONLY)
ASS'Y POWER CORD 230V (98221 ONLY)

(REF. DWG. 98221)

14800 1
17425 1

19490 1
30896 1
19491 1
30897 1
31479 1
31480 1

19499 1
31059 1

16

ES SERIES CARPET SPOTTERS

64230, 98220 & 98221

MAIN ASSEMBLY – EXPLODED VIEW

(REF. DRAWING 98221)

17

ES SERIES PORTABLE CARPET SPOTTERS

64230, 98220, & 98221

HANDLE ASS’Y (REF. DWG. 31215)

ITEM NO. DESCRIPTION PART NO. QTY.

1 Washer-Lock E/T #10 01713 4
2 Screw-Phillips Pan Head Machine #10-24 X 1.000 19617 4
3 Bracket-Pump Mounting (For Reference) 31471 1

4 Handle-Transport 31214 1

18

ES SERIES PORTABLE CARPET SPOTTER

S

64230, 98220, & 98221

ASS'Y VAC./PRESSURE HOSE (REF. DWG. 30744)

ITEM NO. DESCRIPTION PART NO. QTY.

1 Suction Hose, 8' 30735/19529 1
2 Solution Hose Ass'y 30801/19639/19535 1
3 Tool-Utility 30857 1

*4 Plastic Ties-Black 18706 4

* = NOT SHOWN

19

ES SERIES PORTABLE CARPET SPOTTERS

64230, 98220

CIRCUIT ASSEMBLY (REF. DWG. 98220A)

ITEM NO. DESCRIPTION PART NO. QTY.

1 WASHER-LOCK (H/S) #10 01713 1
2 SCREW-TCT (F) PAN HEAD #10-32 X 3/8" 03261 1
3 TERMINAL-CLOSED END CRIMP(INS) 06824 1

*4 STRAIN RELIEF(LIQ.TITE) .35 DIA. CORD 18793 1

5 LEAD-14 GA. X 3" BLACK 19466 2
6 ASSEMBLY-POWER CORD,115V (SPOTTER)

(INCLUDES ITEM 4)
7 ASSEMBLY-POWER CORD,230V (SPOTTER) 19500 1
8 TERMINAL-Q.D.FEMALE 1/4" X 22/18GA. (FUL.INS) 19503 1
9 LEAD-18 GA. X 12"GREEN 19536 1

10 LEAD-16 GA. X 12"BLACK 19537 1
11 LEAD-16 GA. X 12"WHITE 19538 1

OPTIONS AND ACCESSORIES

ITEM NO. DESCRIPTION PART NO. QTY.

19499 1

* TOOL-UTILITY DETAILER (DELUXE) 3-1/2"

98341 1

SPRAY/VAC.

* TOOL-CREVICE DETAILER SPRAY/VAC. 98342 1
* TOOL-UPHOSTERY/CURTAIN (PERFORATED)

98343 1

4"SPRAY/VAC.

* TOOL-UTILITY/STAIR 6" SPRAY/VAC. 98344 1

* = NOT SHOWN

20

ES SERIES PORTABLE CARPET SPOTTERS (230V)

MODEL 98221

CIRCUIT ASSEMBLY /PARTS LIST (ref. drawing 31078)

ITEM

NO.

*1
*2

3
*4
*5
*6

7

8

9

10

*11

12

*13

14

15
16

17

18

19

20
21
22

*23

24

DESCRIPTION PART

WASHER-LOCK (H/S) #10
SCREW-TCT (F) PAN HEAD #10-32 X 3/8"
TERMINAL-CLOSED END CRIMP(INS)
STRAIN RELIEF(LIQ. TITE) .35 DIA. CORD
1/4" INSOLATED FEMALE CONNECTOR(S)
ASSEMBLY-POWER CORD, 115V (SPOTTER)

(INCLUDES ITEM 4)
ASSEMBLY-POWER CORD, 230V (SPOTTER)

LEAD-14 GA. X 3" BLACK ON POWER SWITCH
(INCLUDES ITEM 5 ON ONE END AND ITEM 11 ON THE
OTHER END)
LEAD-16 GA. X 12" BLACK
(INCLUDES ITEM 5 ON EACH END)

LEAD- 16 GA. X 12" WHITE
(INCLUDES ITEM 5 ON EACH END)

5/16" NON-INSOLATED PIGGY-BACK
FEMALE END CONNECTOR(S)

LEAD- 14 GA. X 12" GREEN FROM MOTOR (INCLUDES
ITEM 5 ON ONE END AND ITEM 13 ON THE OTHER END)

3/16" NON-INSOLATED LOOP END CONNECTOR(S)
BLACK LEAD WIRE FROM POWER CORD

(INCLUDES ITEM 5 ON THE END)
TERMINAL-Q.D.FEMALE 1/4"X 22/18GA. (FUL. INS)

WHITE LEAD WIRE FROM POWER CORD
(ICONNECTED TO ITEM 3)

GREEN LEAD WIRE FROM POWER CORD
(INCLUDES ITEM 5 ON THE END)

LEAD- 16 GA. X 12" WHITE FROM PUMP
(INCLUDES ITEM 5 ON ONE END AND
AND IS CONNECTED TO ITEM 3 ON THE OTHER END)

LEAD- 16 GA. X 12" BLACK FROM PUMP
(INCLUDES ITEM 5 ON EACH END)

VACCUM MOTOR 230V/50-60HZ
PUMP-55 PSI/230VAC
FILTER
POWER CORD 230V
POWER SWITCH
* = NOT SHOWN

QTY.

NO.

01713 1
03261 1

06824 1

18793 1
15139 9
19499 1

19500 1
19466 2

19537 1

19538 1

15391 2

80673 1

15200 1

1

19503 1

1

1

19538 1

19537 1

17425 1
31480 1
31067 1
31059 1
30472 1

21

22