Page 1
Operations Manual
For Commercial Use Only
TORNADO INDUSTRIES, LLC
3101 WICHITA COURT
FORT WORTH, TX 76140
PHONE 800-VACUUMS
FAX 817-551-0719
WWW.TORNADOVAC.COM
CK14/1 UPRIGHT VACUUM & CK14/1 BSE UPRIGHT VACUUM
Form No. L8145AA 06/18 ©Tornado Industries, LLC. All rights reserved
MODEL NO: 98147/98145
1
Page 2
Long -Term Buyer Protection Limited Warranty
Tornado Industries, LLC. warrants to the end user/ customer that the Tornado product(s) will be free from
defects in material and workmanship for the duration(s) described below. This limited warranty DOES NOT
cover machines and/or components subject to normal wear and tear, damage that occurs in shipping,
failures resulting from modication, accident, unsuitable operating environment, misuse, abuse, neglect,
or improper maintenance. For full details, contact your Authorized Tornado Distributor, Service Center, or
the Tornado Technical Service Department. Tornado sales and service representatives are not authorized to
waive or alter the terms of this warranty, or to increase the obligations of Tornado under the warranty.
10 Years*
Plastic water tanks and Rotationally-molded bodies
2 Years*
Parts on all Tornado cleaning equipment
1 Year*
Labor on all Tornado cleaning equipment
1 Year*
Warranty on batteries, one year prorated
All battery warranties are handled directly by the battery manufacturer, on a one year prorated basis
Terms subject to change without notice
1. All Windshear™ Blowers, Storm, TV2SS, Side and Downdraft, Insulation Blowers, CV 30, CV 38, CK14/1
PRO, CK 14/1 BSE, CK14/2 PRO, SWM 31/9, CK LW13/1, CK LW 13/1 ROAM, CV 38/48 Dual, PV6, PV10, PV6
ROAM, Wall Mount Vacuum and all chargers are warranted for 1 (one) year for both parts and labor.
2. All non-wear item parts purchased after warranty expiration are warranted for 90 days.
3. Warranty starts from either: The date of sale to the consumer, or 6 months after the dealer purchased
the unit from Tornado (at Tornado’s discretion), whichever comes rst.
4. The EB 30 is warranted for a period of 90 days for both parts and labor.
5. Propane-powered equipment engines are limited to the engine manufacturer’s warranty.
6. Ride-on Scrubbers are warranted for 24 months parts, and 6 months labor, or 1,000 hours, whichever
occurs rst.
Note: Tornado, The Latest Dirt, Floorkeeper, Carpet-
keeper, Carpetrinser, Carpetrinser/Dryer, Headmaster,
Taskforce, PAC-VAC, T-Lite, Glazer, Windshear, Max-Vac
and Trot-Mop are trademarks of Tornado Industries
Website: www.tornadovac.com
Phone 1-800-VACUUMS
Fax 817-551-0719
Address 3101 Wichita Court
Fort Worth, TX 76140
1-800-VACUUMS Over 90 Years of Cleaning Innovation A Tacony Company
Form F2662.©2018. All rights reserved
2
Page 3
NOTES
3
Page 4
GROUNDING INSTRUCTIONS
GROUNDING
OUTLET BOX
This appliance must be grounded. If it should malfunction or breakdown, grounding provides a path of least
resistance for electric current to reduce the risk electric shock. This machine is equipped with a cord having
an equipment -grounding conductor and grounding plug. The plug must be inserted into an appropriate
outlet that is properly installed and grounded in accordance with all local codes and ordinances.
WARNING: Improper connection of the equipment-grounding conductor can result in a risk of electric
shock. Check with a qualied electrician or service person if you are in doubt as to whether the outlet is
properly grounded. Do not modify the plug provided with the appliance - if it will not t the outlet, have a
proper outlet installed by a qualied electrician.
This appliance is for use on a nominal 120-volt circuit, and has a grounding plug that looks like the plug
illustrated in sketch A.
OUTLET
GROUNDING
PIN
The safety label appears
on the machine in the
location indicated. Replace label if it is missing
or becomes damaged or
illegible.
GROUNDED
A
Fig. 2
4
Page 5
Your new Tornado unit is a high quality, precision-made product. All parts used in the manufacturing of this unit
have passed rigid quality control standards prior to assembly. Please safeguard the original receipt / invoice. If
you experience any problems with your unit during the warranty period, the original receipt / invoice will act as
proof of purchase. Contact Tornado for any warranty inquiries.
IMPORTANT SAFETY INSTRUCTIONS
READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE USING THIS UNIT
Read and understand this owner’s manual and all labels on the unit before operating. Safety is a combination of common sense,staying alert and knowing how your unit works. Use this unit only as described in this
manual. Use only manufacturer’s recommended attachments. To reduce the risk of personal injury or damage to your unit use only Tornado recommended accessories.
This machine is intended for commercial use only. It is designed exclusively to pick up dirt, dry debris and
dust in an indoor environment and is not constructed for any other use. The pick up of any type of uid or
dangerous / toxic materials is prohibited. Use only recommended accessories.
READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE.
When using an electrical appliance, basic precautions should always be followed, including the following:
WARNING! To reduce the risk of re, electric shock, or injury:
1. Do not leave appliance unattended when plugged in. Unplug from outlet when not in use and before
servicing.
2. WARNING: ELECTRIC SHOCK COULD OCCUR IF USED OUTDOORS OR ON WET SURFACES.
3. Do not allow to be used as a toy. Close attention is necessary when used by or near children.
4. Use only as described in this manual. Use only manufacturer’s recommended attachments.
5. Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, return it to a service center.
6. Do not pull or carry by cord, use cord as handle, close a door on cord, or pull cord around sharp edges or
corners. Do not run appliance over cord. Keep cord away from heated surfaces.
7. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
8. Do not handle plug or appliance with wet hands.
9. Turn o all controls before unplugging.
10. Do not put any object into openings. Do not use with any opening blocked, keep free of dust, lint, hair,
and anything that may reduce air ow.
11. Keep hair, loose clothing, ngers and all parts of body away from openings and moving parts.
12. Do not pick up anything that is burning or smoking, such as cigarettes, matches or hot ashes.
13. Do not use without vacuum bag and / or lters in place.
14. Use extra care when cleaning stairs.
15. Do not use to pick up ammable or combustible liquids such as gasoline or use in areas where they may
be present.
16. Do not attempt to service the unit while appliance is plugged in.
17. For grounded models, connect to a properly grounded outlet only. See Grounding Instructions.
18. This machine is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the machine by a person responsible for their safety.
19. Keep children and unauthorized persons away from the machine when in use.
SAVE THESE INSTRUCTIONS.
5
Page 6
Hose
Handle
(CK14/1
PRO
ONLY)
Hose Hanger
(CK14/1 PRO
ONLY)
Handle
Tube
Wand
(CK14/1
PRO
ONLY)
Quick
Clean
out Port
(CK14/1
PRO
ONLY)
Furniture Guard
Bag
Compartment
Cover Latch
Bag
Compartment
Fig. 3
Easy Carry
Handle/Cord
Storage Hook
Accessory
Attachment
Opening
Tools
(CK14/1
PRO
ONLY)
ON/OFF
Switch
Power
Cord
Thermal Reset
Button
Genuine Tornado Vacuum Bags
Cleanbreeze (10 per package) 90141
Paper (10 per package) 90147
Genuine Tornado Vacuum Belt (1 per package) 33561
Genuine Tornado Vacuum Filters
Exhaust Filter (1 per package) 90145
HEPA (1 per package) 90144
6
Page 7
How to Attach the Handle to the Vacuum Cleaner
The vacuum cleaner and the handle are packed separately.
1. After rst removing the handle screw, insert handle
into the hole on top of the vacuum cleaner. (Fig. 4)
2. Line up the small hole on the handle with the small
hole on the vacuum cleaner and insert the screw.
Make sure the screw is secured tightly.
On / O Switch
1. To turn the vacuum on, push the switch located
the rear of the unit to the ( I ) position. (Fig. 5)
2. To turn the vacuum o, push the switch located on
the rear of the unit to the ( O ) position.
Fig. 4
Fig. 5
Always operate the vacuum cleaner with a vacuum bag installed.
How to Change the Vacuum Bag
1. Unplug the vacuum cleaner. Remove the bag compartment
Fig. 6
Fig. 7
cover and remove the used bag from the bag holder (Fig. 6).
2. Attach the new vacuum bag onto the bag holder (Fig. 7).
3. Pull the bottom corners of the new vacuum bag (Fig. 8).
4. Reinsert the tab on the end of the bag compartment cover into
the groove on the bag compartment housing. Press it into place
and fasten the bag compartment tightly (Fig. 9).
Fig. 8
Fig. 9
The Edge Cleaning Feature provides improved cleaning of carpets near walls and stationary furniture. For
maximum edge cleaning, use the right side of the vacuum near walls or stationary furniture.
Fig. 10
7
Page 8
The handle on this vacuum cleaner can be set to one of three positions – upright, working or low.
How to Adjust the Handle
1. To release the handle, step on the left rear corner of the vacuum cleaner (Fig. 11).
2. Upright position – for when cleaning tools are being used or for storage (Fig. 12).
Handle locks in this position.
3. Working position – for normal cleaning (Fig. 13).
4. Low position – for cleaning under furniture (Fig. 14).
Fig. 11
Fig. 12
Fig. 13 Fig. 14
Your Tornado vacuum cleaner is equipped with an exhaust lter and a HEPA lter.
These lters capture ne dust particles and protect the motor from dirt. It is important
to replace the HEPA lter approximately every six months.
To Change or Clean the Exhaust Filter
1. Unplug the vacuum cleaner. Remove the bag compartment cover and the bag.
2. Remove the exhaust lter and shake or brush o the dirt (Fig. 15) then replace
lter.
Fig. 15
3. Replace the bag and bag compartment cover.
To Change the HEPA Filter
1. Unplug the vacuum cleaner. Remove the bag compartment cover.
2. Remove the HEPA lter from the front of the bag compartment. (Fig. 16)
3. Insert a new lter and replace the bag compartment cover.
Note: HEPA lters cannot be washed and used again.
Fig. 16
Your Tornado upright vacuum cleaner is designed with a Self-Adjusting Brush Head. No manual adjustments
are required. The height of the brush head is instantly adjusted to carpet pile height. This self-adjusting feature allows the brush head to oat evenly over all carpet pile surfaces.
On-Board Tool Cleaning (CK14/1 PRO ONLY)
This vacuum is equipped with on-board cleaning tools
including a metal telescopic wand, stretch hose, dusting brush and crevice tool.
1. To use the cleaning tools, lift the hose handle
straight up from the vacuum.
2. Extend the wand by pushing the button forward
and pulling the smaller wand out of the larger wand
3. Attach any of the on-board tools to the end of the
wand or if you do not need the wand, any tool can be
connected directly onto the hose handle.
Fig. 17
8
Page 9
CAUTION: Unplug the vacuum cleaner before performing any of these steps.
How to Remove the Bottom Plate
1. Place the vacuum cleaner in the low position (see page 7).
Turn the vacuum over.
2. Slide the clips toward each other (Fig. 18).
3. Remove the bottom plate.
How to Replace the Belt
1. Turn the unit over and remove the bottom plate as described in
the above section.
2. Lift the belt cover and turn toward the outside (Fig. 19 & 20).
3. Remove the agitator by pulling it straight out.
4. Remove the belt from the agitator and motor pulley.
5. Loop a new belt over the motor pulley and over the end of the agitator.
6. Stretch the belt over the agitator while inserting it back into the brush
head housing.
7. Turn the belt cover back over the motor pulley. Make sure cover releases
down into the brush head.
8. Replace the bottom plate by hooking the front end of the plate into the
two ribs on the front end of the brush head housing. (Fig. 21)
Press the bottom plate into place by sliding the clips away from each other.
NOTE: To ensure maximum cleaning eciency, check the belt regularly to
ensure it is in good condition. Replace the belt if it is stretched, cracked or
if excessive slipping is occurring.
Fig. 18
Fig. 19
Fig. 20
CAUTION: Unplug the vacuum cleaner before performing any of these steps.
How to Clean the Brush Head Hose (CK14/1 PRO)
1. Remove the wand from the wand / hose holder as shown on
page 8.
2. Squeeze the tabs on both sides of the quick clean-out port
and pull away from the vacuum (Fig. 22).
3. Check above and below the port opening for obstructions.
4. Remove any obstructions.
5. Replace the quick clean-out port by squeezing both tabs and
pushing it back into the wand / hose holder.
Fig. 21
Fig. 22
9
Page 10
How to Clean the Brush Head Hose (CK14/1 BSE)
The nozzle hose, located on the back of the vacuum cleaner, carries
the dirt from the nozzle to the filter bag. The hose also functions as
the attachment cleaning hose. If the hose should become clogged:
1. Pull out and turn the lid of the cleaning attachment opening.
Remove the clog or blockage (Fig. 23).
2. If the above step is not enough, remove hose cuff from the nozzle
inlet (Fig. 24). Turn the unit over and unscrew and remove the
bottom plate (see “How To Remove Bottom Plate.”). Check nozzle
inlet tube for obstructions. Clear tube and reinstall the bottom plate.
Fig. 23
Fig. 24
CAUTION: Unplug the vacuum cleaner before performing any of these steps.
Thermal Fuse Protection
Your Tornado vacuum cleaner comes equipped with a Manual Reset Thermal Fuse Protector. This thermal protector is designed to protect your vacuum cleaner from overheating due to a cuto in airow (i.e.
clogged hose, operating the vacuum without a bag). Should this situation occur, the thermal fuse protector
will safely shut o your vacuum to avoid and potential damage.
To reset the thermal fuse
1. Unplug the vacuum cleaner.
2. Check for problem (over-lled bag, clog in hose, clogged lters, etc.).
3. Correct problem.
4. Locate ‘tripped’ fuse the small red button located on the bottom of the back
side of the main body roughly one inch to the right of the left wheel. (Fig. 25).
5. Using a pointed object, push the reset button.
6. Plug vacuum cleaner in and begin using.
Fig. 25
For Best Performance
• Keep machine and all accessories clean and in good operating condition.
• Change vacuum bags and lters as recommend to maintain optimum cleaning eciency.
• Always use genuine bags, lters and parts, as use of other products may result in poor cleaning or
ltration performance. Tornado ltration products are designed for maximum performance.
• Have machine checked periodically by the retailer where you purchased your Tornado vacuum.
• Store machine carefully in dry area.
• For optimum cleaning performance and safety, follow your owner’s manual.
Model CK-14/1 PRO CK-14/1 BSE
Voltage / Frequency 120 V / 60 Hz 120 V / 60 Hz
Vacuum motor rating 1200 W / 10A 1200 W / 10A
Bag capacity – dry 3.8 qt / 3.6 L 3.8 qt / 3.6 L
Airow 120 cfm / 3.4 m3/h 120 cfm / 3.4 m3/h
Vacuum – water lift at sealed orice 65 in / 1650 mm 65 in / 1650 mm
Filtration 99.97% @0.3 micron 99.97% @0.3 micron
Brush width 12 in / 305 mm 12 in / 305 mm
Cable length 50 ft / 15 m 50 ft / 15 m
Weight (including cord) 20.6 lb / 9.36 kg 20 lb/9.07 kg
Noise level 69.9 dB(A) 69.9 dB(A)
Construction class I I
Protection IP20 IP20
10
Page 11
Warranty Registration Form
Please Print Clearly
________________________________________________________________________________________________
Company/Institution
___________________________________________ ___________________________________________________
Contact Name Title
___________________________________________ ___________________________________________________
Address City/State/Zip Code
___________________________________________ ___________________________________________________
Phone Fax
___________________________________________ ___________________________________________________
Date of Purchase Email
Selling Dealer:(Required)_____________________________________________________________________________
See white metal plate or sticker on unit for this information.
MACHINE TYPE/MODEL NUMBER: MACHINE SERIAL NUMBER:
1. 1.
2. 2.
3. 3.
4. 4.
Facility Description (please circle all that apply)
1. School 6. Manufacturing 11. Airport 16. Other Govt.
2. Retail Store 7. College/University 12. Warehouse 17. Auto Service
3. Restaurant 8. Hospital 13. Apartment/Condo 18. Non-Prot
4. Ofce Building 9. Nursing Home 14. Supermarket 19. Other (specify)
5. Contract Cleaning 10. Religious Institution 15. U.S. Govt
How did you rst learn about Tornado cleaning and
maintenance equipment?
o Contacted by local dealer
www.tornadovac.com/services/warranty-registration-form.aspx
You can complete this form online at
o Previous experience with Tornado products
o Reputation/Recommendation
o Advertising
o Direct mail
o Website: ____________
o Blog: _______________
This form may also be returned to :
Tornado Industries
3101 Wichita Court
Fort Worth, TX 76140
Fax: 817-551-0719
o Other
Damage or defect arising from abuse, neglect or other misuse is excluded from this warranty. Other items may or may not apply based
on your specic machine. If any defect occurs, and service is attempted by non-Authorized Tornado Service Centers, the warranty will
be void.
©2018 Tornado Industries. All rights reserved.
X8449-TOR 1/2018
11
Loading...