Tork 7100, 7102, 7120, 7122, 7202L Installation And Operating Instructions Manual

TORK MODEL 7100

24 HR. TIME SWITCH

WITH SKIP-A-DAY

SWITCH: SPST
CONTACT RATINGS:

40 AMP 120-277VAC
20 AMP INDUCTIVE

120-277VAC SINGLE PHASE
40 AMP TUNGSTEN 120VAC
1000VA (120-277) PILOT DUTY
2HP 120VAC; 5HP 240VAC

TIMING MOTOR: 120VAC 60Hz
POWER CONSUMPTION: 3 WATTS MAX.

INSTALLATION AND OPERATING INSTRUCTIONS

TO SET ON AND OFF TIMES:

Light trippers turn ON. Dark tr ippers tur n OFF. Place tripper on
dial edge as shown in figure and set point of each tripper to
desired operating time. CAUTION: Note if selected time is AM
or PM. Hold tripper against dial edge and firmly tighten
knurled screw.

Disconnect power at main panel prior to installing or servicing this
time switch or the equipment connected to it.

Connect in accordance with national and local electrical codes.
Supply Connections: Use gauge specified (AWG # 8-14) suitable for

75 degrees C (167 degrees F)

TORK

®

1 GROVE STREET, MT. VERNON, NY 10550 TEL: [phone]

FAX: [phone]

LI-565(A)

▲▲

L

1X

2

LOAD

M

H

N

TO SET DIAL TO TIME: Turn dial counter-clockwise until correct time is indicated by arrow on nameplate .
FOR MANUAL OPERATIONS: Press down lever on right of nameplate to turn ON. Press down lever

on left of nameplate to turn OFF.
TO OMIT ON OPERATION: 7 spoke wheel at lower left of 24 hour dial moves ahead once each day,

about 5 hours before the first ON tripper is set to operate. Insert brass knurled screws in appropriate
spokes on days when ON operations are to be omitted.

TO SET OMITTING WHEEL TO CORRECT DAY: Hold down OFF lever on left of name­plate. The red stud on this lever is the day-indicator. If the ON tripper has already passed
the omitting wheel, turn omitting wheel clockwise until the present day of the week is indi­cated. If ON tripper has not passed omitting wheel, set omitting wheel so preceding day
is indicated (24 hour dial turns counter-clockwise).

TO REMOVE MECHANISM FROM CASE: Press lever near case latch to release mainplate and
swing the movement out. To replace, inser t mainplate projections in slots opposite latch and swing
movement in until it latches.

OFF TIME

(Dark Tripper)

MANUAL

OFF

LEVER

Dial Calibrations

Knurled Screw

O
F

TORK

F

➤

ON TIME

(Light Tripper)

TIME

MANUAL

O
N

LEVER

ACTUATOR

ON

GREEN

RED

STUD

➤

➤

TORK MODEL 7102

24 HR. TIME SWITCH

WITH SKIP-A-DAY

SWITCH: SPST
CONTACT RATINGS:

40 AMP 120-277VAC 40 AMP TUNGSTEN 120VAC

20 AMP INDUCTIVE 1000VA (120-277) PILOT DUTY

120-277VAC SINGLE PHASE 2HP 120VAC; 5HP 240VAC

TIMING MOTOR:

208-277VAC 60Hz

POWER CONSUMPTION:

3 WATTS MAX.

INSTALLATION AND OPERATING INSTRUCTIONS

TO SET ON AND OFF TIMES:

Light trippers turn ON. Dark tr ippers tur n OFF. Place tripper on
dial edge as shown in figure and set point of each tripper to
desired operating time. CAUTION: Note if selected time is AM
or PM. Hold tripper against dial edge and firmly tighten
knurled screw.

TO SET DIAL TO TIME: Turn dial counter-clockwise until correct time is indicated by arrow on name­plate.

FOR MANUAL OPERATIONS: Press down lever on right of nameplate to turn ON. Press down lever
on left of nameplate to turn OFF.

TO OMIT ON OPERATION: 7 spoke wheel at lower left of 24 hour dial moves ahead once each day,
about 5 hours before the first ON tripper is set to operate. Insert brass knurled screws in appropriate
spokes on days when ON operations are to be omitted.

TO SET OMITTING WHEEL TO CORRECT DAY: Hold down OFF lever on left of
nameplate. The red stud on this lever is the day-indicator. If the ON tripper has
already passed the omitting wheel, turn omitting wheel clockwise until the present
day of the week is indicated. If ON tripper has not passed omitting wheel, set omit­ting wheel so preceding day is indicated (24 hour dial turns counter-clockwise).

TO REMOVE MECHANISM FROM CASE: Press lever near case latch to release mainplate and
swing the movement out. To replace, inser t main-plate projections in slots opposite latch and swing
movement in until it latches.

Disconnect power at main panel prior to installing or servicing this
time switch or the equipment connected to it.

Connect in accordance with national and local electrical codes.
Supply Connections: Use gauge specified (AWG # 8-14) suitable for

75 degrees C (167 degrees F)

TORK

®

1 GROVE STREET, MT. VERNON, NY 10550 TEL: [phone]

FAX: [phone]

LI-589(A)

M

▲▲

L

1X

2

H

LOAD

N

OFF TIME

(Dark Tripper)

MANUAL

OFF

LEVER

Dial Calibrations

Knurled Screw

O
F

TORK

F

➤

(Light Tripper)

TIME

MANUAL

O
N

ON TIME

ON

LEVER

GREEN

RED

STUD

➤

➤

ACTUATOR

TORK MODEL 7120

24 HR. TIME SWITCH

WITH SKIP-A-DAY

SWITCH: SPDT
CONTACT RATINGS:

40 AMP 120-277VAC
40 AMP TUNGSTEN 120VAC
20 AMP INDUCTIVE

120-277VAC SINGLE PHASE
1000VA (120-277) PILOT DUTY
2HP 120VAC; 5HP 240VAC

TIMING MOTOR: 120VAC 60Hz
POWER CONSUMPTION:

3 WATTS MAX.

INSTALLATION AND OPERATING INSTRUCTIONS

TO SET ON AND OFF TIMES:

Light trippers turn ON. Dark tr ippers tur n OFF. Place tripper on
dial edge as shown in figure and set point of each tripper to
desired operating time. CAUTION: Note if selected time is AM
or PM. Hold tripper against dial edge and firmly tighten
knurled screw.

TO SET DIAL TO TIME: Turn dial counter-clockwise until correct time is indicated by arrow on name­plate.

FOR MANUAL OPERATIONS: Press down lever on right of nameplate to turn ON. Press down lever
on left of nameplate to turn OFF.

TO OMIT ON OPERATION: 7 spoke wheel at lower left of 24 hour dial moves ahead once each day,
about 5 hours before the first ON tripper is set to operate. Insert brass knurled screws in appropriate
spokes on days when ON operations are to be omitted.

TO SET OMITTING WHEEL TO CORRECT DAY: Hold down OFF lever on left of
nameplate. The red stud on this lever is the day-indicator. If the ON tripper has
already passed the omitting wheel, turn omitting wheel clockwise until the present
day of the week is indicated. If ON tripper has not passed omitting wheel, set omit­ting wheel so preceding day is indicated (24 hour dial turns counter-clockwise).

TO REMOVE MECHANISM FROM CASE: Press lever near case latch to release mainplate and
swing the movement out. To replace, inser t main-plate projections in slots opposite latch and swing
movement in until it latches.

Disconnect power at main panel prior to installing or servicing this
time switch or the equipment connected to it.

Connect in accordance with national and local electrical codes.
Supply Connections: Use gauge specified (AWG # 8-14) suitable for

75 degrees C (167 degrees F)

TORK

®

1 GROVE STREET, MT. VERNON, NY 10550 TEL: [phone]

FAX: [phone]

LI-594(A)

H

N

M

▲
▼

L 1 X 2

LOAD

A

LOAD

B

H

N

OFF TIME

(Dark Tripper)

MANUAL

OFF

LEVER

Dial Calibrations

Knurled Screw

O
F

TORK

F

➤

ON TIME

(Light Tripper)

TIME

MANUAL

O
N

LEVER

ACTUATOR

ON

GREEN

RED

STUD

➤

➤

TORK MODEL 7122

24 HR. TIME SWITCH

WITH SKIP-A-DAY

SWITCH: SPDT
CONTACT RATINGS:

40 AMP 120-277VAC
20 AMP INDUCTIVE

120-277VAC SINGLE PHASE
40 AMP TUNGSTEN 120VAC
1000VA (120-277) PILOT DUTY
2HP 120VAC; 5HP 240VAC

TIMING MOTOR:

208-277VAC 60Hz

POWER CONSUMPTION:

3 WATTS MAX.

INSTALLATION AND OPERATING INSTRUCTIONS

TO SET ON AND OFF TIMES:

Light trippers turn ON. Dark tr ippers tur n OFF. Place tripper on
dial edge as shown in figure and set point of each tripper to
desired operating time. CAUTION: Note if selected time is AM
or PM. Hold tripper against dial edge and firmly tighten
knurled screw.

TO SET DIAL TO TIME: Turn dial counter-clockwise until correct time is indicated by arrow on name­plate.

FOR MANUAL OPERATIONS: Press down lever on right of nameplate to turn ON. Press down lever
on left of nameplate to turn OFF.

TO OMIT ON OPERATION: 7 spoke wheel at lower left of 24 hour dial moves ahead once each day,
about 5 hours before the first ON tripper is set to operate. Insert brass knurled screws in appropriate
spokes on days when ON operations are to be omitted.

TO SET OMITTING WHEEL TO CORRECT DAY: Hold down OFF lever on left of
nameplate. The red stud on this lever is the day-indicator. If the ON tripper has
already passed the omitting wheel, turn omitting wheel clockwise until the present
day of the week is indicated. If ON tripper has not passed omitting wheel, set omit­ting wheel so preceding day is indicated (24 hour dial turns counter-clockwise).

TO REMOVE MECHANISM FROM CASE: Press lever near case latch to release mainplate and
swing the movement out. To replace, inser t main-plate projections in slots opposite latch and swing
movement in until it latches.

Disconnect power at main panel prior to installing or servicing this
time switch or the equipment connected to it.

Connect in accordance with national and local electrical codes.
Supply Connections: Use gauge specified (AWG # 8-14) suitable for

75 degrees C (167 degrees F)

TORK

®

1 GROVE STREET, MT. VERNON, NY 10550 TEL: [phone]

FAX: [phone]

LI-595(A)

Typical for 240VAC supply.

M

L1 X2

H

H

LOAD

A

LOAD

B

H

H

OFF TIME

(Dark Tripper)

MANUAL

OFF

LEVER

Dial Calibrations

Knurled Screw

O
F

TORK

F

➤

ON TIME

(Light Tripper)

TIME

MANUAL

O
N

LEVER

ON

GREEN

RED

STUD

➤

➤

ACTUATOR