Tork 555520A, 555528A Service And Parts Manual

Page 1
Washroom Dispenser Service and Parts Manual Tork Elevation T2 Mini Twin Jumbo Roll Tissue Dispenser 555520A, 555528A Revision Date: 4-28-10
Tork Elevation T2 Mini Twin JBT Dispenser:
T2 System: 555520A (white), 555528A (black) Dispenser Dimensions HxWxD inches (cm):
Tork T2 Mini Jumbo Bath Product Options:
12024402 (Tork Advanced, 2 Ply) 12013902 (Tork Advanced, 1 Ply) 120246 (Tork Advanced, 2-Ply)
Dispenser Parts
Part Description Replacement SKU
LEFT/RIGHT ROLL ARM SPINDLE PAPER ACCESS DOOR HOOD ASSY WHITE HOOD ASSY BLACK (Includes 2 e-clips & pins) 200260 KEY FOR ALL TORK DISPENSERS TORK LOCK
200261 KEYHANDLE FOR KEYLESS ENTRY
225556P (white) 225557P (black)
200260 KEY 200262-10 or
200262-20 200261 KEYHANDLE
1 of 5
Page 2
Washroom Dispenser Service and Parts Manual
c
Tork Elevation T2 Mini Twin Jumbo Roll Tissue Dispenser 555520A, 555528A Revision Date: 4-28-10
Part Description with Replacement Instructions
Parts with SKUs listed are available for order as of the revision date on the manual. Contact an SCA Sales Rep or the SCA Tissue Quality Coordinator to order these parts.
If no SKU is listed, the availability of the part is unknown. Please contact the SCA Tissue Quality Coordinator for more information (see Contacting SCA
section).
Replacement SKU Description & Replacement Instructions
LEFT/RIGHT ROLL ARM
The roll arms sit on the outside of the bath tissue rolls. As the roll is depleted, the roller gets close to the spindle, and allows the access door to unlock and slide to the opposite side for access to the reserve tissue roll. Not replaceable.
SPINDLES
Hold two jumbo bath tissue rolls. Not replaceable.
PAPER ACCESS DOOR
The access door will be locked to one side, allowing access to one of the tissue rolls and blocking access to the other until one roll has completely dispensed.
Not replaceable. 225556P White 225557P Black
T2 MINI TWIN HOOD ASSEMBLY
With door open, locate e-clip holding the hinge piN in place. Use pliers to
remove the e-clip. Pull hinge pin out by pulling out to the left and the right side.
Each hood assembly will include the hood, 2 new e-clips and 2 matching color
hinge pins. 200262-20 TORK LOCK
The lock can be replaced by removing the U-clip from the inside of the dispenser
with a pliers or screwdriver. 200261 KEYHANDLE
SCA 200261 KEYHANDLE
Insert keyhandle into lock to provide keyless access. Note: Lock cannot revert ba
keyed entry once keyhandle has been inserted. 200260 KEY SCA 200260 METAL KEY FOR ALL TORK DISPENSERS
Loading Instructions
1. To fill dispenser after mounting: Open cover. Before loading paper, slide door completely to one side. Raise the each roll arm, placing refill on spindle and resting arm on outside of full roll. Feed the paper through the opening and close the cover. For best performance, rolls should be oriented so each tail feeds over the top of the roll into the center of the dispenser.
2. When one of the rolls is completely dispensed, the access door will unlock and the user will be able to slide it to the opposite side. The user will then have access to the reserve tissue roll.
3. To replenish rolls: Open cover. Raise roll arm and remove the empty cores. Load a new Tork Jumbo Bath Tissue refill onto spindle
Preventive Maintenance
The dispenser should be cleaned any time there is heavy paper dust build-up inside the dispenser. If paper dust is not a problem, approximately every year is a good frequency for cleanings. The following is the recommended procedure to cleaning:
1) Open the dispenser and remove the rolls of paper.
2 of 5
Page 3
Washroom Dispenser Service and Parts Manual Tork Elevation T2 Mini Twin Jumbo Roll Tissue Dispenser 555520A, 555528A Revision Date: 4-28-10
2) Clean out any paper dust. This can be done is several ways, such as, vacuuming, blowing out with a can of compressed air (wear safety glasses), wiping out with a damp cloth, etc.
3) Clean the cover with a general all-purpose cleaner that is safe for plastics
.
Troubleshooting
Problem: Any paper-related problem.
Take note of the date code on the outside of the case of paper product. Then contact the SCA Tissue Quality Coordinator and explain the problem.
Problem: Any other problem not stated above.
Contact the SCA Tissue Quality Coordinator.
Contacting SCA
To contact the SCA Tissue Quality Coordinator, dial 1-866-722-6659 and press 6. Product Date Code Location: The product assembly code can be found on a white sticker placed on the
inside of the dispenser door. The date code is in the following format: DD/MM/YYYY. This is a TorkSelect product. The TorkSelect label is affixed to the inside, right side of the dispenser.
The system identifier (to match product refills) and the dispenser item number are printed on the bottom of this label.
3 of 5
Page 4
Washroom Dispenser Service and Parts Manual Tork Elevation T2 Mini Twin Jumbo Roll Tissue Dispenser 555520A, 555528A Revision Date: 4-28-10
555520A, 555528A Tork ElevationT2 Mini Twin Dispenser
Mounting Diagram
Carton Instructions
4 of 5
Page 5
Washroom Dispenser Service and Parts Manual Tork Elevation T2 Mini Twin Jumbo Roll Tissue Dispenser 555520A, 555528A Revision Date: 4-28-10
Recommended Mounting Height (standard access)
Mount dispenser 27.5” (70cm) above finished floor.
Recommended Mounting Height (ADAAG Guideline)
4.16.6 Dispensers. Toilet paper dispensers shall be installed within reach, as shown in Fig. 29(b)
Dispensers that control delivery, or that do not permit continuous paper flow, shall not be used.
Figure 29b
Grab Bars at Water Closets
Side Wall
A 42 inch (1065 mm) minimum length grab bar is required to the side of the water closet spaced 12 inches (305 mm) maximum from the back wall and extending a minimum of 54 inches (1370 mm) from the back wall at a height between 33 and 36 inches (840-915 mm). The toilet paper dispenser shall be mounted at a minimum height of 19 inches (485 mm). (4.16.3, 4.16.4, 4.16.6)
Note: Compliance with ADA guidelines is the responsibility of the installer and building owner. Local and state requirements may differ from ADAAG guidelines.
.
5 of 5
Loading...