Torin TRF42009 Owner's Manual
OWNER’S MANUAL
2 TON HIGH POSITION HOIST STAND
Item: TRF42009
Questions, problems, missing parts? Before returning to your retailer, call our customer service department at
1-888-44-TORIN (1-888-448-6746), 8 a.m.- 5 p.m., PST, Monday-Friday.
Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure
to follow the safety rules and other basic safety precautions may result in serious personal injury.
Version 20170424
REGISTER
YOUR PRODUCT
http://www.torin-usa.com/
customer-support/
register-a-product.html
SCAN CODE
TECHNICAL SPECIFICATIONS
Description
Item TRF42009
Maximum Capacity 4000lbs.
Minimum Lift Height 48-3/4 inches
Maximum Lift Height 84-1/2 inches
Product Base Size 12in. x 12in.
Weight 42 lbs.
2
IMPORTANT
OWNER / USER RESPONSIBILITY
DO NOT OPERATE OR REPAIR THIS PRODUCT WITHOUT READING THIS MANUAL.
Read and follow the safety instructions. Keep Instructions readily available for operators. Make certain all
operators are properly trained and understand how to safely and correctly operate the product. By proceeding
you agree that you fully understand and comprehend the full contents of this manual. Failure to operate this
product as intended may cause injury or death. The manufacturer is not responsible for any damages or injury
caused by improper use or neglect. Allow product operation only with all parts in place and operating safely.
Use only genuine replacement parts. Service and maintain the product only with authorized or approved
replacement parts; negligence will make the product unsafe for use and will void the warranty. Carefully
inspect the product on a regular basis and perform all maintenance as required. Store these instructions
in a protected dry location. Keep all decals on the product clean and visible. Do not modify and/or use for
any application other than that for which this product was designed. If you have any questions relative to a
particular application, DO NOT use the product until you have rst contacted the distributor or manufacturer to
determine if it can or should be performed on the product.
For technical questions please call 1-888-448-6746.
Before You Begin Register This Product.
For future reference, record the model name, model number, date of manufacture and purchase date of this
product. You can nd this information on the product.
Model Name
Model Number
Date of Manufacture
Date of Purchase
____________________________
____________________________
____________________________
____________________________
INTENDED USE
This product is designed as a means of partial support for, and the positioning of, vehicle components during
their installation/ removal, but not for use in stabilizing or supporting vehicles. For use ONLY under a properly
secured automotive lift.
3
GENERAL SAFETY RULES
GENERAL SAFETY RULES
IMPORTANT SAFETY CONSIDERATIONS
WARNING: Read and understand all instructions. Failure to follow all instructions listed below may result
in serious injury.
WARNING: The warnings, cautions, and instructions discussed in this instruction manual cannot
cover all possible conditions or situations that could occur. It must be understood by the operator
that common sense and caution are factors that cannot be built into this product, but must be supplied by
the operator.
CAUTION: Do not allow persons to operate or assemble this product until they have read this manual and
have developed a thorough understanding of how the product works.
INSPECTION
DO NOT OPERATE OR REPAIR THIS EQUIPMENT WITHOUT READING THIS MANUAL.
To maintain this product and user safety, the responsibility of the owner is to read and follow these
instructions.
• Inspect the equipment for proper operation and function.
• Keep instructions readily available for equipment operators.
• Make certain all equipment operators are properly trained; understand how to safely and correctly operate
the unit.
• Allow unit operation only with all parts in place and operating properly.
• Use only genuine replacement parts.
• Service and maintain the unit only with authorized or approved replacement parts; negligence will make the
equipment unsafe for use and void the warranty.
• Carefully inspect the unit on a regular basis and perform all maintenance as required.
• Store these instructions in a dry secure location for safe keeping.
• Keep all decals on the unit clean and visible.
• Inspect product carefully before each use. Ensure the product is not damaged, excessively worn, or missing
parts.
• Do not use the product unless it is properly lubricated.
• Using a product that is not in good clean working condition or properly lubricated may cause serious injury.
• Inspect the work area before each use. Make sure it is free and clear of any potential hazards.
SAFETY MARKINGS
1. Study, understand, and follow all instructions before operating this device.
2. Do not exceed rated capacity.
3. Use only on hard, level surfaces, with less than 3 degrees of slope.
4. Center load on saddle.
5. Use stands in pairs to stabilize the vehicle before starting repairs.
6. No alterations shall be made to this product.
7. Support only on areas of the vehicle as specied by the vehicle manufacturer.
8. Only attachments and/or adapters supplied by the manufacturer shall be used.
9. Do not use High Reach Stands for any use other than the manufacturer specied usage.
10. Do not use if damaged in any way.
11. NEVER use High Reach Stands on a lawn mower or lawn tractor.
12. Do not move or dolly the vehicle while on support stands.
13. Do not rock the vehicle while working on or around equipment.
14. The following are not recommended for supporting on this equipment: Foundations, Homes,
Mobile Homes, Trailers, RV’s, Campers, nor Fifth Wheels, etc...
15. Failure to heed these markings may result in personal injury and/or property damage.
WARNING!
ASSEMBLY
Use the exploded drawing as your guide to assemble, Lay all parts and assemblies out in front of you
before beginning. The following procedure is recommended:
All numbers in parenthesis () refer to the index number from the parts breakdown.
1. Mount the rubber pad (NO.23) with the saddle
(NO.22), use screw (NO.24).
3. Attach the short pull rods (NO.13) and the long
pull rods (NO.14) with the support bars (NO.3),
using the screws (NO.12) and washers (NO.10).
4. Attach the saddle base (NO.2) with the support
bars (NO.3), using the screws (NO.1), washers
(NO.4) and the nuts (NO.5).
2. Connect the guide plate (NO.7) to the L-brackets
(NO.8) with screws (NO.6), washers (NO.4) and
nuts (NO.5), but do not tighten the screws.
4
6. Attach the outer pillar (NO.18) with handle
(NO.21).Install truss bearing assembly: rst install
the truss bearing (NO.20), after bearing (NO.20)
has been installed and handle (NO.21) has been
attached ,install the threaded rod assembly
(NO.19) by slowing lowering inside.
7. Connect the outer pillar (NO.18) to the saddle
base (NO.2). To adjust the position of the jack
stand, use the Lock Bolt (NO.15), Washer
(NO.16) and Hitch Pin Clip (NO.17).
8. Attach the saddle (NO.22) with the threaded rod
assembly (NO.19) using the screw (NO.6).
5
9. Check that all hardware is secure and tight.
10. Hoist Stand is now ready for use.
5. Mount the L-brackets (NO.8) with the support
pillar (NO.3), using the screws (NO.9), washers
(NO.10) and the nuts (NO.11), then tighten the
screws .
OPERATING INSTRUCTIONS
RAISING THE HOIST STAND
1. Adjust height by rotating the handle CLOCKWISE.
5. Check to ensure vehicle is secure before working
on, around or under.
2. Check to ensure ratchet is secure before loading/
un/loading.
3. Carefully position stand so that load is centeredon
stand’s saddle.
4.Raise saddle to vehicle support point
vehicle,continue to rotate handle clockwise until
loadsupport point is secure. Do not raise any
higherthan load stability will allow.
6
LUBRICATION
A periodic coating of light lubricating oil to pivot
points will help to ensure that pump piston linkages
move freely.
Note: Never apply oil to the saddle. If saddle
extension threads require lubrication; clean thread
surfaces with a clean, dry cloth, then apply a drop of
bearing grease to the threads. Distribute as evenly
as possible along the threaded post.
7
LOWERING THE HOIST STAND
1. Ensure that all tools, equipment and personnel
are clear before lowering load.
2. DO NOT EVER LOWER STAND UNLESS
VEHICLE AND COMPNENTS ARE 100%
SUPPORTED SECURELY. DO NOT EVER
ASSUME LOAD IS SECURE, CHECK BEFORE
LOWERING.
3. With vehicle securely supported on car lift, lower
stand clear of support point.
4. Carefully release stop pin and allow pillar to glide
down to lowest position, re-insert stop pin.
5. Carefully remove stand, then carefully lower
vehicle on car lift.
8
MAINTENANCE INSTRUCTIONS
• Maintain your equipment. It is recommended that the general condition of any equipment be examined
before it is used. Keep your equipment in good repair by adopting a program of conscientious repair and
maintenance. Have necessary repairs made by qualied service personnel.
• Follow the maintenance instructions carefully to keep your equipment in good working condition. Never
perform any maintenance on the equipment while it is under a load.
a. All moving parts of the equipment should be regularly cleaned.
b. Lubricate parts as required by the manufacturer’s specifications. The type of lubricant should be as
specified by the manufacturer or a qualified person. Lubrication systems should be checked to verify
proper operation.
c. If additional maintenance is required, it should be completed in accordance with the instructions of the
manufacturer or qualied person.
Inspection
You should inspect the product for damage, wear, broken or missing parts (e.g.: pins) and that all components
function before each use. Follow lubrication and storage instructions for optimum product performance. Check
the climbing pins to make sure that they are not worn or damaged. Check that everything is good working
condition and that nothing is blocking the holes. Do not use the equipment unless it is in good working
condition.
Binding
If the product binds while under a load, use equipment with equal or a larger load capacity to lower the load
safely to the ground. After un-binding; clean, lubricate and test that equipment is working properly. Rusty
components, dirt, or worn parts can be causes of binding Clean and lubricate the equipment as indicated in
the lubrication section. Test the equipment without a load. If the binding continues, contact Customer Service.
IF YOUR EQUIPMENT BINDS
As your equipment becomes older, the threads may start binding. This will prevent the equipment from
operating properly and safely. Rusty threads, dirty threads, or a worn threads can cause binding. Clean
and lubricate the equipment. Test the equipment without a load. If the binding continues, refer to the after
sale parts and service. If your equipment binds while under a load, use equipment with equal or larger load
capacity to lower the load safely to the ground.
Cleaning
If the moving parts of the equipment are obstructed, use cleaning solvent or another good degreaser to clean
the equipment. Remove any existing rust, with a penetrating lubricant.
Do not use motor oil to lubricate the equipment
Rust Prevention:
-Check daily for any signs of rust or corrosion.
Without a load check for signs of rust that are visible and clean as needed.
Storing the Equipment
1. Store in a dry location, recommended indoors.
2. Equipment should be stored in an area where they will not be subjected to damage.
3. If extreme temperatures or chemically active or abrasive environments are involved, the guidance
provided in shall be followed.
4. Temperature - When equipment are to be used at temperatures above 140"F (60"C) or below -20"F (-29"C),
the equipment manufacturer or a qualied person should be consulted.
5. Chemically Active Environments -The strength and operation of equipment can be affected by chemically
active environments such as caustic or acid substances or fumes. The equipment manufacturer or a
qualied person should be consulted before equipment are used in chemically active environments.
6. Other Environments - The internal workings of equipment can be affected by high moisture, gravel or
sand, silt, grit, or other dust-laden air. Equipment subject to these environments should have their inner
components frequently cleaned, inspected, and lubricated.
Note: If the equipment is stored outdoors, be sure to lubricate all parts before and after use to ensure the
equipment stays in good working condition.
PARTS DIAGRAM
9
PARTS LIST
REF# PART# DESCRIPTION Qty
1 GB5781-M10x25 Hex head screw M10x25mm 3
2 Saddle base 1
3 Support bar 3
4 GB97.1-M10 Washer M10 9
5 GB6170-M10 Nut M10 6
6 GB5781-M10x20 Hex head screw M10x20mm 4
7 Guide plate 1
8 L-bracket 3
9 GB5781-M8x20 Hex head screw M8x20mm 3
10 GB97.1-M8 Washer M8 18
11 GB6170-M8 Nut M8 3
12 GB5781-M8x16 Hex head screw M8x16mm 12
13 Short pull rod 3
14 Long Pull rod 3
15 TRF42009-1 Lock bolt Ø12x72mm 1
16 GB97.1-M12 Washer M12 1
17 TRF42009-2 Hitch Pin Clip Ø1.5x30mm 1
18 Center Pillar 1
19 TRF42009.1 Threaded rod assembly 1
20 GB/T 273.2 Turst bearing 51106 Ø47xØ30x11mm 1
21 TRF42009.2 Handle 1
22 TRF42009.3 Saddle 1
23 TRF42009-3 Rubber pad 1
24 GB70.1-M6x10 Socket head cap screw M6x10mm 4
Safe Operating Temperature is between 40°F – 105°F (4°C - 41°C)
This equipment is covered under a 1-year limited warranty when used as recommended. Only those
items listed with a Part # are available for purchase. For assistance with the operation or the availability of
replacement parts, contact our Parts and Warranty Department at 1-888-44-TORIN (1-888-448-6746). Please
have available a copy of your receipt, the model number of the product, serial number, and specic details
regarding your question.
Not all equipment components are available for replacement; illustrations provided are a convenient reference
of location and position in the assembly sequence.
The manufacturer reserves the rights to make design changes and or improvements to product lines
and manuals without notice.
WARRANTY NOTICE
We want to know If you have any concerns with our products. If so, please call toll-free for Immediate
assistance. For additional web customer support help inquiries visit the Customer Service section at:
http://www.torin-usa.com.
WARRANTY INFORMATION
10
TORIN ONE YEAR LIMITED WARRANTY
Torin Inc.® has been producing quality automotive repair and maintenance products since 1968. All products
sold are felt to be of the highest quality and are covered by the following warranty:
With proof of purchase for a period of one year from the date of that purchase, the manufacturer will repair or
replace, at its discretion, without charge, any of its products or parts thereof which fail due to a defect in
material or workmanship. This warranty does not cover damage or defects caused by improper use, careless
use or abuse of the equipment. This warranty does not cover parts normally considered to wear out or be
consumed in the normal operation of the equipment. Except where such limitations and exclusions are
specically prohibited by applicable law, (1) the CONSUMERS SOLE AND EXCLUSIVE REMEDY SHALL BE
THE REPAIR OR REPLACEMENT OF DEFECTIVE PRODUCTS AS DESCRIBED
ABOVE, and (2) THE MANUFACTURER SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL OR
INCIDENTAL DAMAGE OR LOSS WHATSOEVER, and (3) THE DURATION OF ANY AND ALL
EXPRESSED AND IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, ANY WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IS LIMITED TO A PERIOD OF ONE
YEAR FROM DATE OF PURCHASE. Product alteration in any manner by anyone other than us, with the sole
exception of alterations made pursuant to product instructions and in a workman like manner. You
acknowledge and agree that any use of the product for any purpose other than the specied use(s) stated in
the product instructions is at Your own risk.
Always check for damaged or worn out parts before using any product. Broken parts will affect the equipment
operation. Replace or repair damaged or worn parts immediately. Do not modify the product in any way.
Unauthorized modication may impair the function and/or safety and could affect the life of the equipment.
There are specic applications for which products are designed and tested during production. Manufacturer
provided warranted items are not authorized to be repaired by anyone other than the manufacturer or
manufacture approved repair person. Distributor does not have authorization to amend these statements. You
acknowledge and agree that any modication of the product for any purpose other than manufacturer
completed repairs is at your own risk. Before using this product, read the owner's manual completely and
familiarize yourself thoroughly with the product and the hazards associated with its improper use.
IMPORTANT: BEFORE FIRST USE on any Lift verify that a daily inspection has been completed and that all
components are in the proper working order.
This limited warranty gives you specic legal rights, and you also may have other rights, which vary from
state to state. Some states do not allow limitations or exclusions on implied warranties or incidental or
consequential damages, so the above limitations may not apply to You. This limited warranty is governed by
the laws of the State of California, without regard to rules pertaining to conicts of law. The state courts
located in San Bernardino County, California shall have exclusive jurisdiction for any disputes relating to this
warranty.
Manufacturer reserves the rights to make design changes and or improvements to this product lines and
manual without notice. We at Torin have taken every effort to ensure complete and accurate instructions have
been included in this manual. However, possible product updates, revisions and or changes may have
occurred since this printing. Torin Inc. reserves the right to change specications without incurring any
obligation for equipment previously or subsequently sold. Not responsible for typographical errors.
Alternately Customer Service can be reached through www.torin-usa.com or via email at
info@torin-usa.com.
Not all equipment components are available for replacement, but are illustrated as a convenient reference of
location and position in the assembly sequence. Contact Customer Service for equivalent component. When
you contact us, please have your Product’s Model number, Serial Number and Description ready so that we
may help you efciently. This information can be found on a sticker on the product.
For any warranty support or if your Torin® equipment is not functioning properly contact
Torin® Customer Service directly by telephone at 1-888-44-TORIN (1-888-448-6746)
8:00am – 5:00pm Pacic Time, Monday – Friday
www.torin-usa.com Made in China
11
Loading...