CONTENTS
Brief introduction ....................................................................................1
Main specifications ........................................................................................1
Main configurat ion.. ............................. ..... ............................. ..... ..... ........1
Products constitution.......................................................................................2
Assemble processes........................................... ........................................2
Adjustment steps.........................................................................................4
Safety precautions........... ... ... ... ... ... ... ... ... ...................... ... ... ... ... ... ... ... ....6
Charging method and cautions..................................................................6
Caution and Notice for Li-po batter y .....................................................7
Caution and notice for ESC ....................................................................7
Spare par ts........................................................................................................8
Statement:
1.Please read this manual carefully and follow the instruction of the manual be fore
you use thi s products;
2.Our airplane is n ot a toy, which is only sui table for the experienced manipulator or
under the guidanc e of the experienced pilot.
3. Not recommended for the children under 14 years old.
4.Pleas e adjust this plane according to the instructi on and make sure that the finger
and other parts of your body b e out of the rotating parts of the plane, or it may cause
damage to the plane o r injury to your body.
5.Do not fly in the thunderstorm, st rong wind or bad weather.
6.Never fly the plane where there are power lines overhead, automobiles, near
aerodrome , railway or highway.
7.Never fly our plane where are crowds of people .Give yourself plenty of room
flying, as the plan e can fly at a high speed. Remember that you are responsible for
others safety.
8.Do not attempt to catch the plane when you are flying it.
9.The user should bear ful l responsibility of proper op eration and usage with regards
to this model. We, Top R C together with any distributor of us will not be responsible
for any liability or loss due to improper operation.
Brief i ntroductio n
Th ank you for purch asi ng th e "Blazer"remote control mo del a irp lan es fr om TOP RC , and w e hop e thi s pla ne wi ll
br ing e ndl ess j oy to you after you choose it.
★
Bl aze r is co nfi gur ed wi th tw o mai n win gs. O ne ma in wi ngs i s sui tab le for the beginner, and the other one is suitable
for the middle class or experienced pilot, which can achieve the effect o f one a irp lan e in tw o dif ferent flying way.
★
Wi th th e trainer main wings, it can achieve the s tab le fl ight and e asy to contro l. Ou r Blazer c ann ot st all even u nde r
th e mid dle s pee d or lo wer s pee d fli ght . It al so ca n fin ish i nsi de lo ops , out sid e loo ps, i nverted flight, axial roll and
ot her a ero bat ic ac tio n.
★
Wi th th e spo rts m ain w ing s, it c an ac hie ve the high speed fl igh t and f lex ibl e man ipu lat ion . Bes ide s, it c an fi nis h
lo ops , inverted flight, axial roll and other aerobatic action more sm oot hly.
★
Wi th op tim al de sig n on pr ope lle r, the efficiency is up to 6g/w.With the 11.1V, 22 00m Ah Li po ba ttery, the fl igh t tim e
even can achieve 8-12 minutes.
★
Wi th th e mod ula r des ign a nd hu man ize d des ign o n our B laz er, it can assemble or disasse mbl e the m ain w ing s&
ho rizont al wings & vertical wings& main landing gear easily without any glue or other tools. Rea lly 1 00% c onvenient
to c arr y and m ain tai n.
★
Feat ure d wit h dem oun tab le de sig n for front landing gear, it is not only ensures th e str uct ural strength but also
ac hie ves the effe ct of s hoc k abs orption. The high streng th al umi num a llo y mai n lan din g gea r als o use t he de mou nta ble
de sig n, it c an hi ghl igh t the n ice o utl ook o f it, a lso c an en sur e the s trength of it .
★
Feat ure d wit h opt imi zed s tru ctu re de sig n& du rable and crash -re sis tan ce& h igh p racticality a nd vi vid c olo r sch eme ,
it i s the b est c hoi ce for the beginner.
★
Wi th th e aut oma tic h eat d iss ipa tio n function on the motor, it ensure s the high effi cie ncy a nd pr olo ngs t he us e life
of t he mo tor.
★
On t he co nne cti on be twe en th e ele vator& rudder & fron t whe el jo yst ick a nd se rvo s, ou r bla de us es th e alu min um
al loy regulator,i t mak e eas y to di sas sem ble a nd ad jus t the c ont rol lin g ste el wi re.
★
Al l the s ervos can be detachab le ea sil y, it i s convenient to disassemble and maintain.
Main sp ecificatio ns
★Wi ng Sp an
(1 )Trainer vers ion 1 280 mm
(2 ) Spo rts version 1200mm
★Le ngt h 942mm
★Weight 1152 g
★Th rus t rate 1:1
★Fl yin g tim e ≥8min
Main configuratio n
★Radio system
★Mo tor 35 11- 750 KV
★Ba tte ry 2200 mAh 20C 11 .1V
★ES C
★Se rvo 9gX 4
4C H
TOP
30 A
1
Product constitut ion
RTF versi on
Fu sel age , Wi ngs , Ho riz ont al Wi ng, Vertical Wing, Main Landing Gear,
Front Landing Gear, Propeller, Batter y, Ch arg er, Radio, Acc ess ory B ag.
Trainer Main Sp ort M ain W ing s,
ARF versi on
Ki ts wi tho ut radio
PN P ve rs i on
Ki ts wi tho ut radio, ch arg er an d battery
KIT ve rsion
Wi tho ut any electronic parts
Assem ble processe s
1. Asse mbly of the front l andi ng gea r
Take o f the fuse lag e&front landing gear&hexagon wrench from the box. In ser t the front landing gear to the
mo unt ing h ole a t the b ottom of fuselage. Please make su re th at th e gap p osi tio n of st eel w ire i s ali gne d wit h
th e screw ho les i n the aluminu m all oy sleeve. Then lock the front l and ing g ear b y the H LM3 *3M M scr ew.
2
Assem ble processe s
2. Asse mbly of the main landing gear
Take o f the a lum inu m all oy ma in la ndi ng ge ar an d ins ert i t to th e ass emb lin g gro ove at the underpart of the fuselage.
Pl eas e make sure that the square hole in the landing gear is aligned with the square hole in the plastic mount.
3. Asse mbly of the power system
Take o f the a sse mbl ed po wer s yst em an d pul l the ESC wires f rom t he to p of th e fuselage( Notice: The cowling is
de tac hab le) ,pl eas e con nec t the m oto r wit h ESC p lug ( bla ck wi re of t he mo tor s hou ld be c onn ect ed to b lac k wir e of
th e ESC , red wire of the motor should be connected to the red wire of ESC, yel low wire o f the m oto r sho uld b e
co nne cte d to th e yellow wire of the ESC). Using screw driver to loose the screws (PM3.6MM )at the motor mount,
an d ins ert t he mo tor i nto t he mo tor b ase （P lea se ma ke su re the screws should be locked well). Then lock it well.
4.Assembly of the tail wi ng
Take o f the h ori zon tal w ing s&vert ica l win gs from the box. Pl ease install the horizontal wings&vert ica l win gs to t he
as sem bli ng gr oove at the tail parts of fus ela ge as p er th e rig ht di rec tio n. Th en co nne ct th e con tro lli ng st eel w ire
of r udd er, and make sure tha t the c lip i s at th e out erm ost h ole o n ser vo ar m.
3
Assem ble processe s
5. Asse mbly of the main wings
Take o f the r igh t and l eft m ain w ing s&c onn ect ing p lat e&p las tic l oca tin g sea t&p osi tio ning pin f rom t he box.
Pl eas e con nec t the l eft a nd ri ght w ing s by th e con nec tin g pla te, t hen c onn ect a ile ron s ervo wires. Assemble
th e mai n win gs to t he fuselage and lock it by the plastic locating seat and positioning pin(Please note that the
ga p of po sit ion ing p in is t oward the head of fuse lage ).
6. Finished the assemb ly of "B laz er" .
Adjus tment steps
1. Tur n on th e transmitter a nd pl eas e make sur e tha t the re is enough power for the trans mit ter. Push the joystick
for the thrott le an d thr ott le tr im sw itc h to th e low est p osi tio n, an d keep other trim switc h be in the ne utral position.
4
Adjus tment steps
2.Please connect the battery to the ESC plug, and put the battery into the battery case well, then close the battery cover.
3. Ple ase c atc h the b ack p art o f the fuselage and push the throttle slowly, which can check whether the motor can
wo rk or n ot.
4.Please check the collet to confirm whet her i t bec ome l oos e or no t, an d make sure that the control surfac e is in
accordance with the movement of joy sti ck.
5. Che ck th e cen ter o f gravi ty an d make sure that the CG of the plane should be within the ran ge as i ndi cat ed by
th e arrows .
62-68 m m
5
Adjus tment steps
6. Fin ish ed th e adj ust men t for .“B laz er”
Safety precautions
1. If you have th e sim ula tor, we s ugg est t hat you can pract ise y our s kil l by th e sim ula tor b efore you fly
th is mo del , whi ch wi ll br ing s ome h elp for you.
2. Ple ase c lim b the p lan e abo ve the 50 meters with half throttle to fly it when you f ly it f or your first time,
th en you will be familiar with the performance of this plane.
3. You sh oul d lea rn ho w to co ntr ol th is mo del b lan dly, it wi ll re duc e the p oss ibi lit y of crash and prol ong
th e usa ge li fe of the plane.
4.The turn rad ius s hou ld no t be to o lit tle , or it w ill s tal l and i t wil l inc rea se th e pos sib ility of c rash.
5. Whe n tak ing o ff or landing the plane, you should against the wind.
6. Do no t fly t he mo del over your head or behind you , you s hou ld fl y the m ode l in front of you.
Charging method and cautions
Li-Po bat tery(bal anc e changer) s pecifica tions
Sp eci fic ati ons :
Input voltage: DC 10V~15V
Ou tpu t voltage:2S-3S Li-Po b atter y
Ch arging current: 1.0A
Indicator state:
Green : Charge complete & no battery
Red: Chargin g
Th e batteries are inspected separate ly. When the vo lta ge
reaches 4.20V, the ch arg ing p roc ess s top s.
Operati ng
1.
Th en pl ug ci garette into its socket in car (Adapter should be
co nne cte d if ch arg e at ho me: c onn ect t he ad apt er to home power
so cket, then plug the adapter' DC end to charger). The LED will turn
green indicating i t is re ady for charging.
2. Connect the battery to charger per its interface mark. The LED becomes
red, which means charging is on the way.
3. Whe n LED f las hin g, th e cha rge r wil l ent er th e sta ge of d rip c urr ent
ch arging. The LED turns green when fully charged , and th e batter y
wi ll be u sed a t any time.
6
Notice
1. W hil e cha rging is in process, please do not make it near flammable materials.
2. Exp ect L i pol y battery, th is ch arger is not al low ed for other kinds of battery.
3. W hil e cha rging, please keep it out of the reach of Children.
4. When this charger is in use, please do not go away a nd le ave it unwat che d, if a ny abnor mal ity occurs
(su ch as t he po wer i ndi cat or is o ff, t he te mpe rature of the battery rise rap idl y, et c.) st op ch arg ing i mme dia tel y.
5. P lea se do n ot us e pow er wi th ou tpu t vol tag e hig her t han 1 5V.
6. P lea se do n ot di sas sem ble t he ch arg er or i ts ac ces sor ies .
7. W hen t he ba ttery is not cool down, please do not urge to charge it.
Notice
1. Be fully c harged under no more than 1 A voltage by using the specified charger.
2.Be discharged under 10C voltage but avoiding discharge time too long to harm the battery.
3. Repeat the first and second step one or two times.
4.When the Li-poly battery was s tor ed mo re th an 3 mo nth s, it n eed s to be r ech arged to maintain its voltage,
an d ens ure i ts li fe time.
Safety In struction of Li -Po/Ni-M H battery
1. Do not disa ssemble or re construct the batter y.
2. Do not shor t-circuit the battery.
3. Do not use or leave the battery near by the fire, stove or hea ted place (more than 80℃).
4. Do not immers e the battery in wate r or sea water, do not get it we t.
5. Do not charge the battery under the blazing sunlight.
6. Do not drive a nail into the battery, strike it by hamm er or tread it.
7. Do not im pact or toss the ba ttery.
8. Do not use the batt ery with conspicuous damage or defo rmation.
9. Do not charge a warm ba ttery. Al low it to cool comp letely be fo re attempti ng to charge.
10. Do not reverse charge or over discharge th e battery.
11. Do not con nect the battery to the ordina ry charger so cket or car cigarette jack.
12. Do not use the battery for unsp ecified equipment.
13. Do not tou ch the leakin g battery directly, please wash your skin or cl othes wit h
water if they are be dewed by liquid leakin g fr om the battery.
14. Do not mix the Li- Poly battery with other un-chargeab le battery in usi ng.
15. Do not con tinue cha rging the batte ry over the prescribed time.
16. Do not put the battery into the microwave oven or high -pressu re container.
17. Do not use the abnormal batter y.
18. Do not use or keep the battery under the sunli ght.
19. Do not use the battery nearby the place where generates static electricity (ove r 64 V).
20. Do not cha rge the battery when the environmental te mperature is un der 0℃ or over 45℃.
21. If you find th e battery leaking, smelling or abno rmal, stop us ing it and return it to the seller.
22. When the battery is chargin g, please do no t ma ke it near the flam mable materials!
23. Keep the battery away from the children.
24. Use the specified charger and observe charging requirement (under 1A).
25. When using by minors, parents should show the m to the correct instructi on.
Notific ation for ESC
1. The funct ion of this ESC was in the best condition after facto ry setting; please do not change it by yourself.
2. Before co nnecting the battery, please ma ke sure the throttle an d trim were in the lowest positi on. If the
thrott le and trim were no t in the lowest pos ition by mist ake after connecting the battery, you can cut off the
battery; move the throttl e and push to the lowest position, then connect the ba ttery.
3. The ESC of the ai rplane was in a good co oling position after fac tory asse mbly; ple ase do not move its position.
4. The ESC should be connected to the brushless motor correctly, otherw ise the motor will be reversed turning,
and the model airplane can not fly corre ctly.
7
Spare parts
No:t op 019 01
Tra iner ma in wing s
No:t op01 904
Hori zonta l wing
No:t op01 009
Prop eller
No:t op01 902
Spor ts main w ings
No:t op01 905
Verti cal win g
No:t op01 907
Main l andin g gear
No:t op01 903
Fuse lage
No:t op01 906
Spin ner
No:t op 019 08
Fron t landi ng gear
No:t op 019 09
Cowl ing
No:t op01 912
Conn ectin g plate
No:t op01 910
Main w ings se curin g parts
No:t op01 913
Cont rolli ng stee l wire
8
No:t op01 911
Conn ectin g rod
No:t op20 3
30 A Brus hles s ESC
Spare parts
No:t op30 201
9g Ser vo（400 mm）
No:t op40 202
Mo tor ( TOP3511-750KV)
No:t op30 204
9g Ser vo（15 0mm）
No:
to p507
Ba tte ry（11 .1V,2200mah)
9
Shenzhen Top RC Hobby Co.,Ltd
Loading...