Page 1
BEFORE YOU START
The Sabre S4 is a professional 1/10 scale touring car and should be
built only by persons aged 16 years or older with previous experience
building and operating R/C model cars. This is not a toy and is not
immediately if the car starts to slow down.
• When not using RC model, always disconnec t and removebattery.
• Do not disassemble battery or cut battery cables. If the running
battery short-circuits, approximately 300W of el ectrica l power can be
discharged, leading to fire or burns. Never disassemble battery or cut
INTRODUCTION
intende
d
foruseby
beginner
sorby
children
withou
t
directsupervision
ofa
responsible, knowledgeable adult. Read the instruction manual carefully
before building.
T.O.P. Racing shall not be liable for any loss, injury or damages, whether
direct, indirect, special, inc id enta l, or consequential, arising from the use,
misuse, or abuseof this product and/orany product or accessoryrequired to
operate this product.
GENERAL PRECAUTIONS
•
batterycables
.
• Use a recommended charger for the receiver and transmitter batteries
and follow the instructions correctly. Over-charging, incorrect charging, or
using inferior chargers can cause the batteries to become dangerously hot.
Recharge battery when necessary. Cont in ual recharging may damage
battery and, in the worst case, could build up heat leading to fire. If
battery becomes extremely hot during recharging, please ask your local
hobby shop for check and/or repair and/or replacement.
• Regularly check the charger for potential hazards such as damage to
the cable, plug, casing or other defects. Ensure that any damage is
rectified before using the charger again. Modifying the charger may
This
produc
tisnot
suitable
for
children
under16yearsofage
without
the direct supervision of a knowledgeable adult.
• Assemble this kit only in places away from the reach of small children.
• First-time builders and users should seek advice from people who have
building exper ie n ce in order to assemble the model correctly and to
allowthe model to reach its performancepotential.
• Exercise care when using tools and sharp instruments.
• Take care when building, as some parts may have sharp edges.
• Keep small parts out of reach of small children. Children must n o t
be allowed to put any parts in their mouth, or pull vinyl bag over their
head.
cause short-circuit or overcharging leadi ng to a serious accident.
Therefore do not modify the charger.
• Always unplug charger when recharging is finished.
• Do not recharge battery while battery is still warm. After use, battery
retains heat. Wait until it cools down before charging.
• Do not allow any metal part to short circuit the receiver batteries or
other electrical/electronic device on the model.
• Immediately stop running if your RC model gets wet as may cause short
circuit.
• Please dispose of batteries responsibly. Never put batteries into fire.
•
Immediately
afterusingyour
model,donottouch
equipmen
ton
the
model such as the motor and speed controller, because they generate
high temperatures. You may seriously burn yourself by touching them.
• Follow the operating instructions for the radio equipment at all times.
• Do not put fingers or any objects inside rotating and moving parts, as
this may cause damage or serious injury as your finger, hair, clothes,
etc. may get caught.
• Be sure that your operating frequency is clear before turning on or
running your model, and never share the same frequency with
somebody else at the same time. Ensure that others are aware of the
operating frequency you are using and when you are using it.
EQUIPMENT RECOMMENDED (NOTINCLUDED)
• Radio Transmitter
• Radio receiver
• Batteries for Transmitter
• Electronic Speed Control
• Steering Servo
• Brushless Motor System
• Pinion Gear (48P)
• 7.4V,2 Cell Li-Po (Single Pack)
• 1/10 Touring CarBody Shell
•Always turn on your transmitterbefore turning on thereceiverinthecar.
Always turn off the receiver before turning off your transmitter.
• Keep the wheels of the model off the ground when checking the
operation of the radio equipment.
• Disconnec t thebattery pack befo re storingyour model.
• To prevent any serious personal injury and/or damage to property, be
responsible when operating all remote controlled models.
• The model car is not intended for use on public places and roads or
areas where its operation can conflict with or disrupt pedestrian or
vehicular traffic.
• Do not use
y
our model:
• 1/10 Touring Car
T
ire Set
TOOLSRECOMME NDE D (NO T INCLUDED)
• 1.5mm, 2.0mm, 3.0mm Allen Wrench
• 5.5mm & 7.0mm Hex Socket Wrench
• Modelers Craft Knife
• Turnbuckle Wrench
• Calipers/Ruler
y
1. Near real cars, animals, or people that are unaware that an RC car is
being driven.
2. In places where children and people gather
3. In limited indoor spaces
4. In wet conditions
5. In the street
6. In areas where loud noises can disturb others such as hospitals
and residential areas
7. At nightoranytim eyour lineofsightto the model may be obstructed or
impaired in any way.
•Camber Gauge
• Battery Strapping Tape
• Instant Glue/Thread Lock
• Shock & Gear Diff. Oil
• Joint Grease
• Paint (for Bodyshell)
NOTE:
• The Sabre S4 chassis uses the best available components. All
replacement parts can be purchased from your local hobby or model
Topreven
tany
serious
persona
l
injuryand/ordamag
etopropert
y,please b
e
responsible when operating all remote controlled models.
ELECTRICAL PRECAUTIONS
• Insulate any exposed electrical wiring (using heat shrink tubing or
electrical tape) to prevent dangerous short circuits. Take maximum
care in wiring, connecting and insulating cables. Make sure cables
are always connected securely. Check connectors for if they become
loose. And if so, reconnect them securely. Never use R/C models
with damaged wires. A damaged wire is extremely dangerous, and can
cause short-circuits resulting in fire.
s
h
ops whocarryour products.
• This instruction manual contains a blank setup sheet for your own setup
record.
Enjoy building and driving your Sabre S4S!!
•Lowbattery power will result in loss ofcontrol. Loss ofcontrol can
occur due to a weak battery in either the transmitter or the receiver
Weak running battery may also result in an out of control car if your
car’s receiver power is supplied by the running battery. Stop operation
Page 2
Sabre 4WD - Single Belt
1/10 Touring Car Kit
STEP 1
CA glue
STEP 2
Stainless Steel
Countersunk Head
3x14mm (2)
CA glue
Bearing
10x15x4mm (2)
Page 3
STEP 3
Countersunk Head
2.5x8mm (4)
High
7000cst ~ 10Kcst
Low
1000cst ~ 3000cst
Traction
Note: Gear Diff. Oil Initial 3000cst (1.5g)
Shim
5x9x0.1mm
Shim (2)
10x12x0.3mm
Bearing
10x15x4mm (2)
Collar (2)
10x12x0.9mm
Bearing
5x10x4mm
Chess Head
2x5mm (4)
Bearing
5x8x2.5mm (2)
Spur Gear
48Pitch 87T
Countersunk Head
3x10mm
STEP 4
Washer (2)
Countersunk Head
3x6mm
Countersunk Head
3x14mm
Bearing
5x8x2.5mm (2)
Collar
5x7x0.5mm
Page 4
STEP 5
Front & Rear
Camber Link Position
Countersunk Head
3x6mm (22)
Countersunk Head
3x8mm (8)
Collar
Button Head
3x8mm (8)
3x5.5x2
mm
(2)
Ball Stud
5.3x5mm (4)
Rear Bearing Cam Position
Collar
3x5.5x1mm (2)
Front Bearing Cam Position
Page 5
STEP 6
3mm
Front Suspension Arm
3mm
Set Screw
3x8mm (8)
1.8mm
Rear Suspension Arm
1.8mm
Sus. Mount Toe Angle Chart
FF
0.5 1 1.5 2 2.5 3
FR
- 1 0.5 1 1.5 2 2.5 3
-0.500.511.522.5
0 0 0.5 1 1.5 2
RR
+ 0.500.511.5
+1 0 0.5 1
RR
0.5 1 1.5 2 2.5 3
RF
- 1 1.5 2 2.5 3 3.5 4
-0.511.522.533.5
0 0.5 1 1.5 2 2.5 3
+ 0.500.511.522.5
+ 1 0 0.5 1 1.5 2
Collar
Countersunk Head
3x6mm (4)
Shim
3x5x0.2mm (4)
3x5.5x1mm (8)
FF
Page 6
Set Screw
3x3mm
STEP 7
Make 2 – Rear Hub Set
Make 2 pairs
46 for Front,
44.5 for Rear
Collar
3x5.5x2.5mm
Set Screw
3x10mm
Bearing
5x10x4mm (2)
Make 2 – Steering Block Set
Bearing
5x10x4mm (2)
Castor Assm.
Left
Right
Ball Stud
5.3x8mm
Set Screw
Countersunk Head
3x10mm
3x8mm
Set Scre
w
Set Sc e
3x6mm
Set Screw
3x6mm
Page 7
STEP 8
Steering & Linkages
Make 2 – Front Camber Link
Make 2 – Rear Camber Link
Ball Cup
Countersunk Head
3x8mm (2)
Ball Stud
17.5mm
18mm
Make 2 – Steering Link
Sevro Link
14.5 (10)
Collar
3x5.5x2mm (2)
5.3x5mm (3)
Ball Cup
18.5 (4)
19.5mm
4.3mm
Shim
3x5x0.1mm (2)
Note: Use it when necessary
Button Head
3x6mm
(2)
()
Belt Tensioner
Shim
3x5x0.2mm (2)
Bearing
3x6x2.5mm
Button Head
3x6mm (9)
Bearing Flanged
3x6x2.5mm
Button Head
3x10mm
Page 8
STEP 9
Make 4 - Stabilizer Bar Link
2.5mm
Ball Stud
5.3x8mm
Rear
Stabilizer Bar
1.2mm (Copper)
Set Screw
3x3mm (8)
Ball C
up 10.
5
Ball Cup 14.5
Front
Stabilizer Bar
1.4mm (Silver)
Make 4 - Shock Assembly
2mm E-clip (2)
Note : Shock Initial Setup
Front: Oil 400cst / Spring 14x1.5x6.00 (344)
Rear : Oil 400cst / Spring 14x1.5x6.50 (306)
1.0mm
1.2mm
Note : Shock Piston Initial Setup
Front
Rear
Button Head
3x6mm
Button Head
3x6mm
Page 9
STEP 10
Bumper & Body Post
Countersunk Head
Button Head
3x10mm (2)
M3 Nuts (3)
3x8mm (5)
Button Head
3x6mm (4)
Sevro Mount & Sevro Arm
Countersunk Head
3x6mm (4)
Button Head
3x6mm
Countersunk Head
3x12mm
Collar
3x5.5x5mm
Collar
3x5.5x1mm
Spacer
3x7mm (3)
Button Head
3x6mm (3)
Countersunk Head
3x6mm (3)
Set Screw
3x10mm
Collar
3x7x3mm
Page 10
STEP 11
Motor & Battery Guide
Spacer
3x7mm (4)
Countersunk Head
3x8mm (2)
M3 Lock Nut (4)
Countersunk Head
3x10mm (4)
Y
our Sabre
S4S i
s now ready to
RUN !!!
Page 11
S4S Standard Parts List
Steering Shock Absorber
TC-SCH029RD Bell Crank Bridge (included bearing) PO-PSH009RD Alloy Shock Spring Holder Ver.2 (4pcs)
Chassis TC-SCH030RD Bell Crank Arm (included bearing) PO-PSH002 Shock Teflon O-Ring Guide for Shock Ver.2 (4pcs)
SK-CH1002 Body Post Set PO-PSH102 Optional Shock Piston 1.0 x 2 Holes (4pcs)
TC-PCH20H Foam Bumper Linkage PO-PSH103 Optional Shock Piston 1.0 x 3 Holes (4pcs)
TC-PMPS01 Servo Arm & Mount MC-MLK001 3 x 15mm Tie Rod Steel (2pcs) PO-PSH122 Optional Shock Piston 1.2 x 2 Holes (4pcs)
TC-PMQS01 Bumper & Body Post Set PA-HBS003 5.3mm Steel Ball ( 5pcs ) PO-PSH123 Optional Shock Piston 1.2 x 3 Holes (4pcs)
TC-PXCH020RD Optional Top Deck Post PA-HBS0505 5.3 x 5mm Ball Stud (5pcs) PO-PSHT08 Titanium Coated Shock Shaft Ver.2 (2pcs)
TC-SCH018RD Sabre Series Bulkhead Cover LH & RH Ver.2 (Red 1pair) TC-PMHS01 Ball Cup 14.5 (8pcs) PP-010321 Oil Mixed O-Ring for Dampers 40° (10pcs)
TC-SCH028RD Sabre - Bulkhead Ver.2 (Red) TC-PMHS02 Ball Cup 18.5 (4pcs) PP-XR50RD Oil Mixed X-Ring for Dampers (10 pcs)
TC-SCH031RD
S4 -St
eering Post (1pc
)
TC-PSU005
3
x 30mm Tie Rod Steel (2pcs
)
TC-SCH041RD S4S - Belt Tensioner Set Stabilizer
TC-SCH042BK S4S - Motor Mount Accessores PO-PSB101WH Stabilizer Bar Set 1.1, 1.3 & 1.5 (White) (each 1pc)
TC-SCH043RD S4S - Floating Sevro Mount AW-BW31RD Small M3 Bevel Washer Red (10pcs) TC-PSB010 1.0mm Stabilizer Bar (2pcs)
TC-SCH044RD Muti Sevro Mount Post (1pc) PA-AP0001 Aetenna Post (2 pcs) TC-PSB016 1.6mm Stabilizer Bar (2pcs)
TC-SCHC045 S4S -Main Chassis PA-AT0001 Antenna Tube (4 pcs) TC-PSB018 1.8mm Stabilizer Bar (2pcs)
TC-SCHC046 S4S -Top Deck PA-ATC001 Antenna Tube Cap (4pcs)
TC-SCHC047 S4S -Floating Sevro Mount Plate PA-BPS3SV Short Body Clip M6 Silver (20pcs)
TC-SCHC048 S4S -Front Shock Tower PA-ER0020 M2 E-Clip (30 pcs) Shock Spring
TC-SCHC049 S4S -Rear Shock Tower PA-SP0307 Steel Flat Washer Black (10pcs) PS-TR15550 Gamma Shock Spring (14 x 1.5 x 5.50) 393gf/mm , 22.0lb/in
TC-SCHC050 Battery Mount Plate +1.5mm (1pc) PP-010320 Oil Mixed O-Ring for Dampers 30° (10pcs) PS-TR15575 Gamma Shock Spring (14 x 1.5 x 5.75) 367gf/mm , 20.5lb/in
PT-NTW001 Nuts & Tie -Rod Wrench PS-TR15625 Gamma Shock Spring (14 x 1.5 x 6.25) 324gf/mm , 18.1lb/in
Drive Train TC-SLB001 Sabre Decal Sticker PS-TR15675 Gamma Shock Spring (14 x 1.5 x 6.75) 289gf/mm , 16.2lb/in
PA-HSS101
Gear Diff Hard Shim Set ( Large 4pcs & Small 8pcs)
PS-TR15700
Gamma Shock Spring (14 x 1.5 x 7.00) 274gf/mm
, 15.
3lb/in
PA-SP0208 Steel Pin 2x8mm (8pcs) Spacer PS-TR15725 Gamma Shock Spring (14 x 1.5 x 7.25) 260gf/mm , 14.6lb/in
PO-DT0018H Alloy Gear Diff. Outdrive Hard (2pcs) AW-S100RD 3mm x 1.0t Collar Red (10pcs) PS-TR15750 Gamma Shock Spring (14 x 1.5 x 7.50) 248gf/mm , 13.9lb/in
PO-DT1009RD Gear Diff Spacer Set (each 2pcs) AW-S150RD 3mm x 1.5t Collar Red (10pcs) PS-TF17625 Alpha Shock Spring (13 x 1.7 x 6.25) 626gf/mm , 35.0lb/in
PO-MGAS03 Small Bevel Gear Holder AW-S200RD 3mm x 2.0t Collar Red (10pcs) PS-TF17650 Alpha Shock Spring (13 x 1.7 x 6.50) 591gf/mm , 33.1lb/in
PO-MGAS04 40T Gear Diff. Case & New O-ring Set AW-M300RD Ultra Wide 3mm x 3.0t Collar Red (10pcs) PS-TF17675 Alpha Shock Spring (13 x 1.7 x 6.75) 560gf/mm , 31.3lb/in
PO-MGBS01 Bevel Gear Set (Large 2pcs & Small 4pcs) AW-M5050RD 5mm x 0.5t Collar Red (8pcs) PS-TF17700 Alpha Shock Spring (13 x 1.7 x 7.00) 532gf/mm , 29.8lb/in
PO-PDT003 Spool Outdrives - Steel (2pcs) PS-TF17725 Alpha Shock Spring (13 x 1.7 x 7.25) 507gf/mm , 28.3lb/in
PO-PDT101 40T Gear Differential Set (Belt Drive) Screw PS-TF14575 Beta Shock Spring (13 x 1.4 x 5.75) 347gf/mm , 19.4lb/in
PP-GDRS02 Gear Diff. O-Ring Set (Large 3pcs & Small 6pcs) PA-BM0306BK Button Head Screw M3 x 6 (10pcs) PS-TF14600 Beta Shock Spring (13 x 1.4 x 6.00) 325gf/mm , 18.2lb/in
TC-PMJS04 Front Spool Pulley Ver.2 PA-BM0308BK Button Head Screw M3 x 8 (10pcs) PS-TF14625 Beta Shock Spring (13 x 1.4 x 6.25) 306gf/mm , 17.1lb/in
TC-PML104 Bearing Cam ( 4pcs) PA-BM0310BK Button Head Screw M3 x 10 (10pcs) PS-TF14650 Beta Shock Spring (13 x 1.4 x 6.50) 294gf/mm , 16.2lb/in
TC-SDT030 S4S - Main Belt PA-CM0306BK Countersunk Head Cap Screw M3 x 6 (10pcs) PS-TF14675 Beta Shock Spring (13 x 1.4 x 6.75) 274gf/mm , 15.3lb/in
TC-SDT031 S4S - Centre Shaft P
A
-CM0308BKCountersunk Head Cap Screw M3 x 8 (10pcs
)
p(p)
TC-SDT032RD S4S - 20T Center Pulley Set PA-CM0310BK Countersunk Head Cap Screw M3 x 10 (10pcs) Spur Gear
TC-SDT033RD S4S - 20T Center Pulley (1pc) PA-CM0312BK Countersunk Head Cap Screw M3 x 12 (10pcs) 48 Pitch 64 Pitch
TC-SDT035RD S4S - Main Belt Holder Set PA-CM0314BK Countersunk Head Cap Screw M3 x 14 (10pcs) SG-K48066 Spur Gear 48P 66T SG-K64084 Spur Gear 64P 84T
TC-SDT036 S4S - Main Belt Holder Shaft PA-CM2508BK M2.5x8mm Countersunk Head Screw (8pcs) SG-K48069 Spur Gear 48P 69T SG-K64086 Spur Gear 64P 86T
PA-SCM205BK Chess Head Cap Screw M2 x 5 (8pcs) SG-K48072 Spur Gear 48P 72T SG-K64088 Spur Gear 64P 88T
Drive Shaft SG-K48073 Spur Gear 48P 73T SG-K64096 Spur Gear 64P 96T
PO-DT0021 C - Joint Blades (8pcs) Nut SG-K48074 Spur Gear 48P 74T SG-K64100 Spur Gear 64P 100T
PO-DT1004RD Clamp Type 5.2mm Hex wheel Adapter Set (Red) (each 4pcs) PA-FN00M3 Flat Nut M3 (10pcs) SG-K48075 Spur Gear 48P 75T SG-K64104 Spur Gear 64P 104T
PO-DT0016 Universal Pin for Axle Pin Holder (8pcs) PA-LN00M3 M3 Steel Nylon Lock Nut (10pcs) SG-K48076 Spur Gear 48P 76T SG-K64108 Spur Gear 64P 108T
PO-SDT009RD Aluminium Universal Bone 46mm (Red) (1pc) PA-SNF4BK M4 Steel Serrated Wheel Nut Black (10pcs) SG-K48077 Spur Gear 48P 77T SG-K64112 Spur Gear 64P 112T
PO-SDT018 Axle Shaft (1pc) SG-K48078 Spur Gear 48P 78T SG-K64116 Spur Gear 64P 116T
PO-SDT019 Locked Universal Join Set (each 1pc) Set Screw SG-K48081 Spur Gear 48P 81T SG-K64120 Spur Gear 64P 120T
PO-SDT021RD
A
luminium Universal Shaft Set 46mm (Red) (each 2pcs) PA-SS0303BKSteel Set Screw M3 x 3 (10pcs
)
SG-K48084 Spur Gear 48P 84T SG-K64124 Spur Gear 64P 124T
()( p)
(p)
p
p
PO-SDT026RD 44.5mm Aluminum Universal Bone (1pc) PA-SS0306BK Steel Set Screw M3 x 6 (10pcs) SG-K48090 Spur Gear 48P 90T
PO-SDT027RD 44.5mm Aluminum Universal Bone Set (each 2pcs) PA-SS0308BK Steel Set Screw M3 x 8 (10pcs) SG-K48093 Spur Gear 48P 93T
PA-SS0310BK Steel Set Screw M3 x 10 (8pcs)
Ball Bearing Linkage
PA-SB0603 Ball Bearing 3 x 6 x 2.5mm (2pcs)
S4S Option Parts List
PO-HBS0505RD 5.3 x 5mm 7075 Ball Studs (5pcs)
PA-SB0603F Flanged Ball Bearing 3 x 6 x 2.5mm (2pcs) PO-HBS0508RD 5.3 x 8mm 7075 Ball Studs (5pcs)
PA-SB0805 Ball Bearing 5 x 8 x 2.5mm (2pcs) Chassis PA-HBS0510 5.3 x 10mm Ball Stud (5pcs)
PA-SB1005 Ball Bearing 5 x 10 x 4mm (8pcs) PA-BMT01BK Battery Mount Tape - Black PO-HBS003RD 5.3mm Alum. Ball - Red (5pcs)
PA-SB1005T Steel Bearing 5 x 10 x 3mm (2pcs) PA-BMT01RD Battery Mount Tape - Red AW-TB0330RD 30mm Aluminum 7075 Tie Rod Red (2pcs)
PA-SB1510 Ball Bearing 10 x 15 x 4mm (4pcs) PO-PCH019 Graphite Bumper Upper Plate Set PO-S4STRS1 S4S - Aluminum Tie Rod Set Red (7pcs)
TC-PCH20L Foam Bumper - Light Weight AW-TB0335RD 35mm Aluminum 7075 Tie Rod Red (2pcs)
Suspension PO-SLK3015RD 15mm Al. Tie Rod Red (2pcs)
4152-P4S1 King Pin Collar (4pcs) Drive Train
4216R-P4S1 Sus. Mount 3.0 PO-DT0019 Steel Gear Diff. Outdrive (2pcs)
A
ccessores
PO-SSU005RD Suspension Mount Separate (2pcs) PO-SDT115 Hybrid Spool Set (S4 & S4 Mini) SS-KM01BK Middle Size Sevro Savers
PO-SSU009RD Sus. Mount 1 TC-SDT029 Spool Outdrive - Steel (2pcs)
TC-MABS01 Castor Block - 4 (1pair) TC-PMJS02 Photon One-Way Pulley Nut
TC-MACS01 Steering Block & Rear Hub Ver.2 (each 1pc) AW-FN03RD Aluminum Flat Nut M3 Red (5pcs)
TC-MACS02 Steering Block & Rear Hub Ver.3 (each 1pc) Drive Shaft AW-LNF4RD M4 Aluminum Flange Nylon Nut Red (5 pcs)
TC-PMES01 Suspension Arm F&R (each 1pc) PO-DT1006RD Clamp Type 6.2mm Hex wheel Adapter Set - Red (4pcs) AW-SNF4RD M4 Alum.Serrated Wheel Nut Red (4pcs)
TC-PSU001 23mm Hinge Pin (2pcs) PO-DT1007RD Al. Axle Pin Holder - Red (each 4pcs)
TC-SSU001 Mounting Ball (8pcs) PO-DT1008RD Clamp Type 4.5mm Hex wheel Adapter Set - Red (4pcs) Titanium Screw
TC-SSU002 44mm Hinge Pin (2pcs) PO-SDT025RD Aluminum Universal Bone 43mm - Red (1pc) TI-SF0305 M3x5 Titanium Button Head Hex Screws (6 pcs)
PO-SDT028 Steel Universal Bone 44.5mm (1pc) TI-SF0306 M3x6 Titanium Button Head Hex Screws (6 pcs)
Shock Absorber PO-SDT029 Double-Joint Dog Bone (1pc) TI-SF0308 M3x8 Titanium Button Head Hex Screws (6 pcs)
TC-PMMS02 Shock Parts PO-SDT030 Double-Joint Axle (1pc) TI-SF0310 M3x10 Titanium Button Head Hex Screws (6 pcs)
TC-PMRS01
Shock Piston Parts
PO-SDT031
Double-Joint Holder (1pc)
TI-SC0305
M3x5
Titanium Countersunk Head Hex Screws (6 pcs)
TC-PSH002 Shock Bladder (4pcs) PO-SDT035 Double-Joint Universal Set 46 (1pair) TI-SC0306 M3x6 Titanium Countersunk Head Hex Screws (6 pcs)
TC-PSH008 Shock Shaft Ver.2 (2pcs) PO-SDT037 Double-Joint Insert Set (each 2pcs) TI-SC0308 M3x8 Titanium Countersunk Head Hex Screws (6 pcs)
TC-PSH101RD Shock Body Set Ver.2 (each 1pc) PO-SDT038 Double-Joint Dog Bone 44.5 (1pc) TI-SC0310 M3x10 Titanium Countersunk Head Hex Screws (6 pcs)
TC-PSHS01RD Shock Set Ver.2 (2 sets) PO-SDT039 Double-Joint Universal Set 44.5 (1pair) TI-SC0314 M3x14 Titanium Countersunk Head Hex Screws (6 pcs)
Shim Ball Bearing Set Screw
PA-100305 3 x 5 x 0.1,0.2,0.3mm Shim (each 10pcs) PO-CB0805 Ceramic Ball Bearing 5x8x2.5mm PA-SS0303 M3x 3mm Stainless Steel Hex Socket Set Screw (10 pcs)
PA-100507 5 x 7 x 0.1,0.2,0.3mm Shim (each 10pcs) PO-CB1005 Ceramic Ball Bearing 5x10x4mm PA-SS0304 M3x 4mm Stainless Steel Hex Socket Set Screw (10 pcs)
PA-101012 10 x 12 x 0.1,0.2,0.3mm Shim (each 10pcs) PO-CB1510 Ceramic Ball Bearing 15x10x4mm PA-SS0306 M3x 6mm Stainless Steel Hex Socket Set Screw (10 pcs)
PO-CBST12 Ceramic Ball Bearing Set for T.O.P. S4S (17pcs) PA-SS0308 M3x 8mm Stainless Steel Hex Socket Set Screw (10 pcs)
Shock Spring PA-SS0310 M3x10mm Stainless Steel Hex Socket Set Screw (8 pcs)
PS-TR15600 Gamma Shock Spring (14 x 1.5 x 6.00) 344gf/mm , 19.2lb/in Suspension PA-SS0312 M3x12mm Stainless Steel Hex Socket Set Screw (8 pcs)
PS-TR15650
G
amma Shock Spring
(14
x 1.5 x 6.
50) 306gf/
mm , 17.
1lb/i
n
4215R-P4S1
S
uspension Mount 2.5 deg. Re
d
PO-PMZS01 Light Weight CF Suspension Arms F & R (each 1pc)
Spur Gear PO-PSU010RD Aluminum Steering Block Ver.2 (2pcs)
SG-K48087 Spur Gear 48P 87T PO-PSU011RD Aluminum Rear Hub Ver.2 (2pcs)
PO-SSU001RD Suspension Mount 1.5 deg. Red
Stabilizer PO-SSU002RD Suspension Mount 2.0 deg. Red
4252R-SET4 Stabilizer Retainer (4pcs) PO-SSU011RD Sep. Mount Height Spacer Set 0.5 & 1.0mm Red (each 4pcs)
PA-HBS0508 5.3 x 8mm Ball Stud (5pcs) PO-SSU010RD Height Spacer Set 0.5 & 1.0mm Red
TC-PSB012 1.2mm Stabilizer Bar ( 2pcs ) PO-SSU016RD Suspension Mount Separate +/-0.5 (1pair)
TC-PSB014 1.4mm Stabilizer Bar ( 2pcs ) TC-MABS02 Castor Block - 6 Ver.2 (1pair)
TC-PSU003RD Threaded Sway Bar Adjuster (2pcs) TC-MACS01 Steering Block & Rear Hub (each 1pc)
Page 12
SETUP RECORD
Name: Date:
Track: Country:
Condition
:Temperature
:
ACKERMANN
SPACES
mm
REAR DRIVE
Gear Diff.
cst.
STEERING MOUNT
Main Chassis
Sevro Plate
Both
FRONT DRIVE
Std. Spool
Alloy Spool
Gear Diff.
cst.
SINGLE BELT DRIVE TRAIN
TOE
deg.
deg.
RF mm
TOP DECK
- SCREW
- NO SCREW
FR mm
MOTOR POSITION
Rear
Center
FRONT
MEASUREMENTS
FRONT
SHOCKS
RIDE HEIGHT mm OIL WEIGHT wt / cst
CAMBERANGLE deg
PISTON
Opt.
1.0mm 2hole
ROLLBAR mm
Std.
1.2mm 3hole
DOG BONE BLADDER
NOTES: SPRING
REBOUND %
REAR MEASUREME NT S REAR SHOCKS
FRONT
4
mm
1 3
2
mm
1 2 3 4 5 6
1
2
3
mm
Steering Block
Std.
Opt.
Alloy
RIDE HEIGHT mm OIL WEIGHT wt / cst
CAMBERANGLE deg
PISTON
Opt.
Std.
1.0mm 2hole
ROLLBAR mm
1.2mm 3hole
DOG BONE BLADDER
NOTES: SPRING
REBOUND %
MOTOR
PINION GEAR
FRONT REAR
BRAND
1 3
mm
WHEEL HUB
SPACER
mm
2
mm
FF mm
FR mm
Standard
Suspension Arm
Optional
SPUR GEAR
BATTERY
BODY SHELLS
WING
ESC SETTING
COMPOUND
INSERT
WHEEL
TIRETREATMENT
REAR
4
13
2
mm
WHEEL HUB
1 2 3 4 5
Rear Hub Carrie
r
Std.
Opt.
Alloy
mm
24
NOTES:
1 3
5
RF mm
RR mm
mm
SPACER
mm
1 3
Standard
Suspension Arm
mm24
Optional
Loading...