Toppro TDX26 PLUS User Manual

TDX26 PLUS

TDX

TDX26 PLUS

MODE

PRESET

DELAY

EDIT

UTILITY

PREV NEXT

CARD

ENTER

ESC

MUTE

MUTE MUTE MUTE MUTE MUTE

SAFETY RELATED SYMBOLS

This symbol, wherever used, alerts you to the presence of un-insulated and dangerous voltages within the product enclosure. These are voltages that may be sufficient to constitute the risk of electric shock or death.

This symbol, wherever used, alerts you to important operating and maintenance instructions.

Please read.

Protective Ground Terminal

AC mains (Alternating Current)

Denotes the product is turned on.

Denotes the product is turned off.

WARNING

Describes precautions that should be observed to prevent the possibility of death or injury to the user.

CAUTION

Describes precautions that should be observed to prevent damage to the product.

WARNING

Power Supply

Ensure that the mains source voltage (AC outlet) matches the voltage rating of the product. Failure to do so could result in damage to the product and possibly the user. Unplug the product before electrical storms occur and when unused for long periods of time to reduce the risk of electric shock or fire.

External Connection

Always use proper ready-made insulated mains cabling (power cord). Failure to do so could result in shock/death or fire. If in doubt, seek advice from a registered electrician.

Do Not Remove Any Covers

Within the product are areas where high voltages may present. To reduce the risk of electric shock do not remove any covers unless the AC mains power cord is removed. Covers should be removed by qualified service personnel only.

No user serviceable parts inside.

Fuse

To prevent fire and damage to the product, use only the recommended fuse type as indicated in this manual. Do not short-circuit the fuse holder. Before replacing the fuse, make sure that the product is OFF and disconnected from the AC outlet.

Protective Ground

Before turning the unit ON, make sure that it is connected to Ground. This is to prevent the risk of electric shock.

Never cut internal or external Ground wires. Likewise, never remove Ground wiring from the Protective Ground Terminal.

Operating Conditions

Always install in accordance with the manufacturer's instructions.

To avoid the risk of electric shock and damage, do not subject this product to any liquid/rain or moisture.

Do not use this product when in close proximity to water.

Do not install this product near any direct heat source. Do not block areas of ventilation. Failure to do so could result in fire. Keep product away from naked flames.

Disposing of this product should not be placed in municipal waste but rather in a separate collection.

IMPORTANT SAFETY INSTRUCTIONS

Read these instructions Follow all instructions Keep these instructions. Do not discard. Heed all warnings. Only use attachments / accessories specified by the manufacturer.

Power Cord and Plug

Do not tamper with the power cord or plug. These are designed for your safety.

Do not remove Ground connections! If the plug does not fit your AC outlet seek advice from a qualified electrician.

Protect the power cord and plug from any physical stress to avoid risk of electric shock.

Do not place heavy objects on the power cord. This could cause electric shock or fire.

Cleaning

When required, either blow off dust from the product or use a dry cloth. Do not use any solvents such as Benzol or Alcohol.

For safety, keep product clean and free from dust.

Servicing

Refer all servicing to qualified service personnel only. Do not perform any servicing other than those instruct

-ions contained within the User's Manual.

Carts and stands - The component should be used only with a cart or stand that is recommended by the manufacturer. A component and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the component and cart combination to overturn.

The mains plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.

TDX

1. ........................................................................................................1

INTRODUCTION

2. ..................................................................................................................1

FEATURES

3. ............................................................................................................1

USEFUL DATE

4.FRONT PANEL... ..........................................................................................................3

5.REAR PANEL.................................................................................................................5

6.SIGNAL PROCESSING...................................................................................................6

7.GETTING STARTED........................... ...........................................................................7

9.FIRST SETUP................................................................................................................10

10.DISPLAY INFORMATION IN DEFAULT CONDITIONS....................................................11

11.MENU MAP ..............................................................................................................14

8.SYSTEM CONFIGURATION...........................................................................................8

12.PRESET MENU ..........................................................................................................18

13.DELAY MENU ...........................................................................................................22

14.EDIT MENU... ...........................................................................................................25

15.UTILITY MENU...........................................................................................................34

16.GANGING SUBMENU................................................................................................34

17.CONFIGURATIONS....................................................................................................43

18.CONNECTIONS..........................................................................................................46

19.FACTORY PRESETS ....................................................................................................53

20.TECHNICAL SPECIFICATIONS.....................................................................................54

21. ...........................................................................................................55

GUARANTEE

22.NOTE ........................................................................................................................56

Thank you for purchasing TOPP PRO product, the TDX26 PLUS. is 2 In Digital Signal Processor for speaker management. For the input section, thereare Input Gain, 8 bands Parametric Equalizer(PEQ)and delay functions for the stereo input signal processing. In the 6 / 4 output channels section, there are equipped with Input selection, 5-band Parametric Equalizer, Crossover, Delay, Gain, Limiter,and Mute.In order to make the users understand the ways of operation conveniently, it uses the LEDs and LCD to indicate the respective parameter settings.

TDX26 PLUS

Please read this manual carefully so you can take advantages of all the features of the . Thanks again for choosing TOPP PRO.

TDX26 PLUS

2 balanced Inputs and 6 balanced Outputs

10 FACTORY PRESETS+64 USER PRESETS+128 CARD PRESETS

5 LEDs for every Channel Level Display

Digital Audio Input with Sample Rate Converter

Output Mute button for every output channel

USB user interface for PC software control

RS-485 multi-units linking interface

Input Gain Control from -30 to +6 dB

5-band Input parametric EQ with 0.05 Oct. Frequency step