Topp Music Gear TMW-9161 User Manual
SEIKAKU TECHNICAL GROUP LIMITED
PHFWA102-20080300002,A,1
A3
A4
A5
MAR.01.2008
TOPP PRO
/
TMW-9161R/T/M/P TOPP PRO_V1.0
0.18Kg/1
105g
TMW-9161R/T/M(PE03006)
9
PGBSC001-20071200090
17
NF03123
TMW-9161 SERIES
WIRELESS MICROPHONE SYSTEM
TMW-9
161
NF03123-1.0
SAFETY RELATED SYMBOLS
This symbol, wherever used, alerts you to the
presence of un-insulated and dangerous voltages
within the product enclosure. These are voltages
that may be sufficient to constitute the risk of
electric shock or death.
This symbol, wherever used, alerts you to important
operating and maintenance instructions.
Please read.
Protective Ground Terminal
AC mains (Alternating Current)
AC mains (Alternating Current)
Denotes the product is turned on.
Denotes the product is turned off.
WARNING
Describes precautions that should be observed to
prevent the possibility of death or injury to the user.
CAUTION
Describes precautions that should be observed to
prevent damage to the product.
WARNING
Power Supply
Ensure that the mains source voltage (AC outlet)
matches the voltage rating of the product. Failure to
do so could result in damage to the product and
possibly the user. Unplug the product before electrical
storms occur and when unused for long periods of time
to reduce the risk of electric shock or fire.
External Connection
Always use proper ready-made insulated mains
cabling (power cord). Failure to do so could result in
shock/death or fire. If in doubt, seek advice from a
registered electrician.
Do Not Remove Any Covers
Within the product are areas where high voltages may
present. To reduce the risk of electric shock do not
remove any covers unless the AC mains power cord is
removed. Covers should be removed by qualified service
personnel only.
No user serviceable parts inside.
Fuse
To prevent fire and damage to the product, use only
the recommended fuse type as indicated in this
manual. Do not short-circuit the fuse holder. Before
replacing the fuse, make sure that the product is OFF
and disconnected from the AC outlet.
Protective Ground
Before turning the unit ON, make sure that it is connected
to Ground. This is to prevent the risk of electric shock.
Never cut internal or external Ground wires. Likewise, never
remove Ground wiring from the Protective Ground Terminal.
Operating Conditions
Always install in accordance with the manufacturer's
instructions.
To avoid the risk of electric shock and damage, do not
subject this product to any liquid/rain or moisture.
Do not use this product when in close proximity to water.
Do not install this product near any direct heat source.
Do not block areas of ventilation. Failure to do so could
result in fire.
Keep product away from naked flames.
Disposing of this product should not be placed in
municipal waste but rather in a separate collection.
IMPORTANT SAFETY INSTRUCTIONS
Read these instructions
Follow all instructions
Keep these instructions. Do not discard.
Heed all warnings.
Only use attachments / accessories specified by the
manufacturer.
Power Cord and Plug
Do not tamper with the power cord or plug. These are
designed for your safety.
Do not remove Ground connections!
If the plug does not fit your AC outlet seek advice
from a qualified electrician.
Protect the power cord and plug from any physical
stress to avoid risk of electric shock.
Do not place heavy objects on the power cord. This
could cause electric shock or fire.
Cleaning
When required, either blow off dust from the product
or use a dry cloth.
Do not use any solvents such as Benzol or Alcohol.
For safety, keep product clean and free from dust.
Servicing
Refer all servicing to qualified service personnel only.
Do not perform any servicing other than those instruct
-ions contained within the User's Manual.
Carts and stands - The
component should be used
only with a cart or stand
that is recommended by
the manufacturer.
A component and cart
combination should be
moved with care. Quick
stops, excessive force,
and uneven surfaces may
cause the component and
cart combination to overturn.
TMW
SERIES
TMW
SERIES
NOTE
9
TABLE OF CONTENTS
1. INTRODUCTION.........................................................................................4
2. FEATURES.................................................................................................5
3. USEFUL DATA............................................................................................6
4. CONTROL ELEMENTS................................................................................6
5. OPERATION........... ...................................................................................9
6. CONNECTION DIAGRAM ...........................................................................11
7. TECHNICAL SPECIFICATION.....................................................................12
8. GUARANTEE.............................................................................................14
9. NOTE........................................................................................................15
TMW
SERIES
TMW
SERIES
TMW
SERIES
INTRODUCTION
The TMW-9161 is the delicately designed UHF, PLL synthesized system, with antenna built inside
the receiver for smart switching diversity control, the higher level RF signals maybe fed into the
system for greater reliability and coverage, therefore, the risks of breakdown and interference
are to be effectively reduced. You can manually adjust the channel of the transmitter to match
that of the receiver if you know about the operating frequency of it.
PLL UHF DIVERSITY RECEIVER
HANDHELD TRANSMITTER
BODY PACK TRANSMITTER
Generally, the TMW-9161 series consists of:
PLL UHF Diversity Receiver
Handheld Transmitter
Body Pack Transmitter
Thank you for choosing TOPP PRO.
Our Professional Audio Products are designed and tested by a highly qualified engineering team
with more than 20 years of experience. Great pride & care is placed in delivering products with
excellent performance, specifications and dependable reliability. Also great emphasis is placed in
creating and bringing to market products that can fill multiple applications and also offer customers
exceptional value.
Our creative and dedicated design & engineering team uses the latest tools in technology and the
latest concepts in acoustics design to create products for real-life applications. Every TOPP PRO
Audio product is tested and must comply to very strict Standards.
TMW
SERIES
TM
W9161
TMW
SERIES
INTRODUCTION
For the TMW-9161 series, there are several types of clip microphones are included in this product
range, please make sure that the proper microphone has been selected for your typical sound
reinforcement system before installation.
Last but not the least, the operating frequency of this system may be varied from 798 MHz to 827 MHz, please
refer to your national EMC regulations to pick out the authorized frequency band (0 ~ F) for your end application.
HM-38, Condenser Microphone
Preset impedance: 600 ohm;
Freq. response: 80-12 kHz;
Sensitivity: -68 dB+/-3 dB at 1 kHz;
Directional: Uni-directional;
Weight: 52 g (0.12Ib)
HM-58, Condenser Microphone
Preset impedance: 700 ohm;
Freq. response: 200-8 kHz;
Sensitivity: -65 dB at 1 kHz;
Directional: Uni-directional;
Weight: 54 g (0.12Ib)
FEATURES
PLL UHF DIVERSITY RECEIVER
Pressing the flip switch to switch channel for desired Radio Frequency
LED indication RF
One receiving module
AF level display
one balanced output
one squelch control
one volume control
Soft touch painting for comfortable use
Channel frequency adjusted manually
TRANSMITTER
COMMON FEATURES
PLL synthesized design
Consistent operating frequencies to comply with the EMC regulations
16 channels frequency presets
Manufactured under ISO9000:2000, ISO/TS16949:2002 Quality Management System
TMW
SERIES
Loading...