Top Innovations MC1407 User Manual
MODEL MC1407
Fabric Steamer
by Top Innovations, Inc.
Please read all instructions before use.
Mail in your warranty registration card.
LETTER FROM THE CEO
Dear Valued Customer,
Congratulations on purchasing your new MC1407 Fabric Steamer. This powerful
product is designed to effectively smooth wrinkles and reduce odors with a minimum of
time and effort.
Turn your Fabric Steamer on, and in less than a minute you are ready to delicately
remove wrinkles from garments, draperies and upholstery. With 1500 Watts of power
and a forty-five minute maximum steam time, this Fabric Steamer is capable of
handling everything from big steaming jobs, to quick touch-ups. With the convenient
Clothes Hanger Hook, you can hang garments right on the unit for steaming. In fact, the
Fabric Steamer is so versatile that it can effectively steam drapes while they are still
hanging, eliminating the hassle of taking them down! This wrinkle-removing power
means that the Fabric Steamerwill let you care for your precious fabrics and garments
the way you’ve always wanted to.
Top Innovations, Inc. would like to invite you to visit our Customer Support Web site at:
www.topinnovations.com
On this website you will find additional information about many other exciting products
that are available, helpful tips on ways in which you can utilize your Fabric Steamer,
and other useful information to assist you in maximizing the power of steam!
Enjoy your new MC1407 Fabric Steamer!
Benny Lee
Chairman and CEO
Top Innovations, Inc.
2
Top Innovations, Inc.
IMPORTANT SAFEGUARDS
WARNING: To reduce the risk of fire, electrical shock, or injury,
the following basic safety precautions should always be followed
when using an electrical appliance.
READ ALL INSTRUCTIONS BEFORE USING YOUR STEAMER
1. DO NOT leave your MC1407 Fabric Steamer unattended when plugged in or not
in use.
2. This unit is not a toy
near children, pets and plants. Steam produced by unit is hot and
pressurized. Care must be taken to avoid burns or other injuries. Never
point nozzle at people or pets.
3. Always unplug electrical cord when unit is not in use. DO NOT use this unit if
electrical cord or outlet is damaged. DO NOT use unit if it is not working
properly or has been dropped, damaged, or left outdoors. If such damage occurs,
contact our Customer Service Department (see page 14 of this manual) for
service and repair assistance.
4. This unit is an electrical appliance. DO NOT submerge it in water. DO NOT
use Steam Hose or electrical cord as a handle. DO NOT allow cord or Steam
Hose to be crimped by closing them in doors. DO NOT pull or stretch cord or
Steam Hose around sharp corners or edges. Be sure to keep electrical cord away
from all heated surfaces.
5. DO NOT use this unit with extension cords or electrical outlets that have
inadequate current capacity. A three-prong outlet or a properly grounded adapter
is necessary when using MC1407 Fabric Steamer.
6. In order to unplug MC1407 Fabric Steamer, grasp plug and pull smoothly and
firmly from outlet. DO NOT attempt to unplug unit by pulling or tugging on
electrical cord.
. Close supervision is required when using unit
7. Use caution when operating unit as burns can occur from touching hot metal
parts, or from proximity to hot water or steam.
8. To reduce the likelihood of circuit overload, do not operate another high wattage
appliance on the same circuit.
SAVE THESE INSTRUCTIONS!
FOR HOUSEHOLD USE ONLY
Top Innovations, Inc.
3
IMPORTANT SAFEGUARDS
WARNING: To reduce the risk of electrical shock, this appliance
has a three-pronged plug. This plug will fit in a polarized wall
outlet only one way. If the plug does not fit fully in the outlet,
contact a licensed electrician to install a proper outlet. DO NOT
attempt to modify the plug or defeat this safety feature.
9. DO NOT handle or use this unit while hands are wet or when not wearing shoes.
To avoid falls and other injuries, be sure to dry any wet areas on floors and to
stand away from damp surfaces while using steamer.
10. MC1407 Fabric Steamer is only meant to be used with recommended MC1407
accessories. Other types of attachments are not to be used with this unit.
Doing so may cause injuries or damage to unit.
11. Nozzles and attachments become hot during use. To avoid injuries, DO NOT
touch nozzles while using this appliance. DO NOT attempt to change
attachments while unit is emitting steam.
12. DO NOT turn unit on its side when in use.
13. When filling your Fabric Steamer with water, DO NOT fill Water Tank with
more than 40 oz. (1,183 ml.) of water.
14. Before filling unit with water, always take the following steps:
(1) Turn appliance off
(2) Unplug electrical cord
Failure to follow these steps may result in electrical shock and injury.
15. Only water should be used in unit. Other cleaning agents will damage unit and
can cause injuries.
16. DO NOT operate unit if steam opening is blocked. Should this occur, shut unit
off and unplug.
17. Store your MC1407 Fabric Steamer in a cool, dry place. Allow unit to cool
completely, and always drain Water Tank and Reservoir before storing.
SAVE THESE INSTRUCTIONS!
FOR HOUSEHOLD USE ONLY
4
Top Innovations, Inc.
FABRIC STEAMER PRODUCT INFORMATION
The following features and accessories are included with your Steamer. Carefully inspect
packaging material as some parts are shipped inside Styrofoam packaging. To obtain
possible missing parts, refer to the Customer Support section on page 14 of this manual.
UNIT FEATURES AND
ACCESSORIES
1. Pole Top
1a. Clothes Hanger Hook
1b. Steam Nozzle Holder
2. Fabric Brush
3. Steam Nozzle
4. Handle
5. Steam Hose
6. Hose Base
7. Telescopic Pole
8. Pole Base
9. Water Tank
10. Valve Cap
11. Water Reservoir
12. Lighted On/Off Switch
13. Drain Plug
14. Rolling Casters
15. Press Pad
Top Innovations, Inc.
5
FABRIC STEAMER PRODUCT INFORMATION
• The Pole Top (1) is comprised of the Clothes Hanger Hook (1a) and Steam Nozzle
Holder (1b). The Clothes Hanger Hook allows you to steam garments that are
hanging from a clean, rust-free hanger. The Steam Nozzle Holder provides a safe
and convenient place to hang the Steam Nozzle.
• The Fabric Brush (2) attachment connects to the Steam Nozzle and is designed to
assist in removing lint, loose threads and exceptionally stubborn wrinkles.
• The Steam Nozzle (3) emits hot, penetrating steam.
• The Handle (4) is ergonomically designed for comfort and ease of use, while
remaining relatively cool and safe to grasp during the steaming process.
• The Steam Hose (5) directs steam from the boiler to the Steam Nozzle, and is
designed to be flexible while safely containing the steam.
• The Hose Base (6) is the threaded pipe which connects the Steam Hose to the
main unit.
• The Telescopic Pole (7) connects the Pole Top to the steamer, and can be extended
and retracted for convenient use and quick storage.
• The Pole Base (8) is the point at which the Telescopic Pole connects to the main
unit, ensuring a stable mount for the Telescopic Pole.
• The Water Tank (9) holds water to be used in the Water Reservoir, and is
removable for easy filling and emptying.
• The Valve Cap (10) controls the flow of water between the Water Tank and Water
Reservoir, and must be removed in order to fill and empty the Water Tank.
• The Water Reservoir (11) is where water is stored before being converted into
steam by the boiler. Water is introduced into the Water Reservoir through the
Valve Cap on the Water Tank.
• The Lighted On/Off Switch (12) activates and deactivates the unit, as well as
provides a clear visual indication that the unit is powered on.
• The Drain Plug (13) is designed to easily empty water out of the
• The Rolling Casters (14) allow for exceptional mobility and freedom of
movement.
• The Press Pad (15) fits on your hand, allowing you to support the fabric for a
more thorough steaming. The Press Pad also protects your hand from being
burned by hot steam.
Water Reservoir.
REPLACING ACCESSORIES
To order a replacement Press Pad or Fabric Brush, visit the Products section of our
website, www
6
.topinnovations.com, or call 1-800-711-6617.
Top Innovations, Inc.
ASSEMBLING THE FABRIC STEAMER
ASSEMBLING THE TELESCOPIC POLE
1. Screw Pole Extension (FIGURE 1-A) onto top section of Telescopic Pole
(FIGURE 1-B). Rotate in a clockwise direction until tight and secure.
2. Place Pole Top onto top of Pole Extension as shown (FIGURE 2) and rotate in a
clockwise direction until tight and secure.
3. Loosen top ridged knob (FIGURE 3-C) by turning it in a counter-clockwise
direction. Pull top section of Telescopic Pole (FIGURE 3-E) upwards to extend it
to full height. Re-tighten top ridged knob.
4. Loosen bottom ridged knob (FIGURE 3-D) by turning it in a counter-clockwise
direction. Pull middle section of Telescopic Pole (FIGURE 3-F) upwards to
extend it to full height. Re-tighten bottom ridged knob.
5. Telescopic Pole is now fully assembled and extended. To reduce Pole back to
compact height, reverse steps 3 and 4.
NOTE: The Telescopic Pole must be fully extended during steamer operation
in order to insure a free flow of steam through the Steam Hose.
FIGURE 1 FIGURE 3
FIGURE 2
Top Innovations, Inc.
7
ASSEMBLING THE FABRIC STEAMER
ATTACHING THE TELESCOPIC POLE
1. Loosen Pole Base by turning it in a counter-clockwise direction.
2. Insert bottom section of Telescopic Pole into Pole Base (FIGURE 4).
3. Tighten Pole Base by turning it in a clockwise direction until it is tight, and
Telescopic Pole sits firmly in place (FIGURE 5).
FIGURE 4
ATTACHING THE FABRIC BRUSH
1. Make sure Lighted On/Off Switch is set to “Off”
position, and that the unit is not emitting any steam. Do
not try to connect Fabric Brush while unit is emitting
steam, as this can cause burns and injury.
2. Align the four pegs on back of Fabric Brush (2 circular
and 2 elongated) with corresponding holes on face of
Steam Nozzle.
3. Press Fabric Brush firmly onto Steam Nozzle, until it fits
snugly and firmly in place (FIGURE 6).
8
Top Innovations, Inc.
FIGURE 5
FIGURE 6
ASSEMBLING THE FABRIC STEAMER
ATTACHING THE STEAM HOSE
1. Place end of Steam Hose onto threaded Hose Base (FIGURE 7).
2. Rotate knob in clockwise direction until Steam Hose is tightly secured onto Hose
Base (FIGURE 8). Hand tighten only. Do not over-tighten.
3. Hang Steam Nozzle on specially designed Steam Nozzle Holder (FIGURE 9).
FIGURE 7
CAUTION: To prevent steam from causing bodily injury or damage to
surfaces, always hang the Steam Nozzle on the Steam Nozzle Holder when not
in use.
Do not lay the Steam Hose on the floor as condensation may occur, causing
unwanted water droplets in the steam.
Do not pull on the Steam Hose with excessive force as this may damage it,
resulting in a steam leak.
Your new MC1407 Fabric Steamer is now fully assembled and ready for use.
Please continue reading this manual for instructions on using the Fabric Steamer, as
well as directions for cleaning and storage.
FIGURE 8
FIGURE 9
Top Innovations, Inc.
9
USING THE FABRIC STEAMER
FILLING WATER TANK AND WATER RESERVOIR
IMPORTANT: Always make sure that Lighted On/Off Switch is set to “Off”
position and unit is unplugged before attempting to fill Water Tank.
1. Remove Water Tank from main unit.
2. Holding Water Tank upside-down, unscrew and remove Valve Cap by rotating it
in a counter-clockwise direction (FIGURE 10).
3. Fill Water Tank with water through Valve Cap Hole. Refer to guidelines on left
side of Water Tank to fill it with correct amount of water, depending on desired
steam time (15, 30, or 45 minutes). Do not exceed 45 MIN (40 oz. / 1,183 ml.)
mark.
NOTE: To prolong life of unit, it is recommended that you use distilled or
de-mineralized water in Water Tank. Do not attempt to substitute another
water tank for the one designed for use with this unit.
4. Replace Valve Cap by rotating it in a clockwise direction.
5. Place Water Tank back onto main unit (FIGURE 11). The sound of water flowing
from Water Tank into Water Reservoir should be audible for a short period of
time.
IMPORTANT: Do not attempt to operate Fabric Steamer with an empty
Water Tank, as doing so could result in damage to the unit.
10
FIGURE 10
FIGURE 11
Top Innovations, Inc.
USING THE FABRIC STEAMER
OPERATING THE FABRIC STEAMER
1. Make sure that Water Tank is filled with water and placed correctly onto main
unit, and that Fabric Brush is securely attached if you wish to use it.
2. Plug power cord into a convenient 3-prong electrical outlet (FIGURE 12).
3. Switch Lighted On/Off Switch to “On” position (FIGURE 13).
4. Unit requires approximately 35-40 seconds for boiler to heat. Once it has heated,
Fabric Steamer will begin producing a flow of steam.
NOTE: It is common for unit to produce gurgling sounds and small
amounts of water during the first few minutes of steaming. This is a natural
part of the steaming process. Pointing Steam Nozzle towards the ground and
shaking it gently may help to remove excess water from Steam Hose more
quickly (FIGURE 14).
5. Once steam flow is steady and excess water has been removed from Steam Hose,
you may proceed with your steaming tasks. Refer to Tips for Using the
Fabric Steamerguide on page 12 of this manual for more information about
steaming garments and other fabrics.
6. When you have completed your steaming tasks, immediately switch Lighted
On/Off Switch to “Off” position and unplug power cord from electrical outlet.
Refer to Proper Storage section on page 13 of this manual for information on
proper cleaning and storage of Fabric Steamer.
FIGURE 12
FIGURE 13 FIGURE 14
Top Innovations, Inc.
11
USING THE FABRIC STEAMER
TIPS FOR USING THE FABRIC STEAMER
STEAMING GARMENTS
1. Place garment on a clean, rust-free clothes hanger.
2. Place hanger (with garment) on Clothes Hanger
Hook (FIGURE 15).
CAUTION: Use care when handling garments
on the Clothes Hanger Hook. Pulling on the
garment with too much force may cause the unit
to tip over.
3. Grasp Handle, and direct Steam Nozzle towards
bottom of garment. Steam will rise along inside and
outside of fabric, removing wrinkles. Slowly slide
Steam Nozzle vertically, from bottom to top of
garment (FIGURE 16).
NOTE: Do not allow kinks to form in hose at
any time during use.
4. Direct Steam Nozzle away from garment and
smooth fabric with your free hand.
5. Repeat steps 3 and 4 as necessary until fabric is
smooth and wrinkle free.
FIGURE 15
FIGURE 16
OTHER STEAMING TIPS
• Curtains and draperies may be steamed while still hanging.
• To remove wrinkles from towels, handkerchiefs and napkins, drape them over a
rod or towel rack and gently steam them.
• Heavier fabrics may require repeated steaming to effectively remove wrinkles.
• To remove exceptionally stubborn wrinkles steam both sides of fabric.
• For additional assistance in removing tough wrinkles, or to remove lint and other
particles, attach Fabric Brush to Steam Nozzle (see Attaching the Fabric Brush
section on page 8 of this manual).
• Use Press Pad in order to steam difficult spots and edges and to create creases in
fabric. Slide your hand through the velcro strap on back of Press Pad to secure it
to your hand. This will protect your hand from the flow of hot steam. Then steam
fabric while pressing it firmly but gently against the Press Pad.
12
Top Innovations, Inc.
CARE &STORAGE GUIDELINES
PROPER STORAGE
Preparing your Fabric Steamer for storage is quick and simple. When you have
finished your steaming tasks, follow the steps listed below.
1. Set On/Off Switch to “Off” position, and unplug grounded power cord from
electrical outlet.
2. Allow unit to cool completely.
3. Remove Water Tank from unit and unscrew Valve Cap to drain remaining water
into sink or tub.
4. Remove Drain Plug and drain any remaining water in Water Reservoir into a
sink or tub to prevent overfilling during your next use. Flush out Water
Reservoir with fresh water to minimize potential mineral build-up in Water
Reservoir. Replace empty Water Tank.
5. Loosen two ridged knobs on Telescopic Pole, and press down on Pole Top to
collapse Pole into compact storage position.
6. Store Fabric Steamer in a cool, dry place.
REMOVING MINERAL BUILD-UP
A common problem with steam appliances is mineral build-up caused by high
mineral content in many municipal water supplies. The best way to avoid this is
to use de-mineralized or distilled water in unit. If you are unable to use demineralized or distilled water, we recommend you use this procedure monthly to
help avoid mineral build-up:
1. Unplug power cord from electrical outlet and allow unit to completely cool.
2. Remove Water Tank from unit and drain it into sink or tub.
3. Remove Drain Plug and drain water from Water Reservoir into sink or tub.
4. Using measuring cup (not included), make a mixture of 10 oz. (296 ml.) vinegar
and 10 oz. (296 ml.) water.
5. Slowly pour water-vinegar solution into Water Reservoir.
6. Allow to stand for 40 minutes.
7. Drain water-vinegar solution from Water Reservoir.
8. Rinse Water Reservoir with fresh water, drain and repeat until vinegar odor
dissipates.
9. Replace empty Water Tank.
Top Innovations, Inc.
13
TROUBLESHOOTING &CUSTOMER SUPPORT
PROBLEM
Unit fails to steam. Lighted
On/Off Switch does not
illuminate.
Unit fails to steam. Lighted
On/Off Switch does
illuminate.
Excessive gurgling in Steam
Hose and Steam Nozzle /
water drips from Steam
Nozzle.
POSSIBLE CAUSE
Unit is not plugged in. Plug into electrical
Household Circuit Breaker /
Ground Fault Interrupter has
tripped or blown a fuse.
Water Tank is empty. Refill Water Tank using
Mineral build-up in unit. Follow Removing Mineral
Condensation in Steam Hose.
SOLUTION
outlet.
Reset Circuit Breaker /
Ground Fault Interrupter, or
replace fuse. If you need
assistance, contact a licensed
electrician.
procedures on page 10 of this
manual.
Build-Up procedure on page
13 of this manual.
Some gurgling is a natural
effect of steaming process.
For excessive gurgling or
dripping water, point Steam
Nozzle towards ground and
shake to remove excess water
droplets.
Steam output is weak or
intermittent.
Mineral build-up in unit. Follow Removing Mineral
Build-Up procedure on page
13 of this manual.
CUSTOMER SUPPORT
For problems with your Fabric Steamer, please refer to the troubleshooting solutions located
abovel. Additional inquiries should be directed to our Customer Support services through our
Web site, www
If you do not have internet access, you may also contact our Customer Support Department
by telephone, at (800) 711-6617 or (816) 584-9700.
NOTE: In order for our customer service representatives to help you as quickly and
efficiently as possible, please have the following information ready before calling:
• Purchase information (where and when you purchased this product)
• Product Serial Number
.topinnovations.com
, on the Service Request Web page.
14
Top Innovations, Inc.
WARRANTY INFORMATION
ONE YEAR LIMITED WARRANTY
(If outside USA, additional shipping charges may apply)
Top Innovations, Inc. warrants this product to be free from defects in material and
workmanship for a period of one (1) year from the date of purchase. This warranty
does not cover damage caused by misuse, negligence, use by improper current or
voltage, commercial use, use contrary to operating instructions or disassembly, repair or
alteration by any person other than Top Innovations, Inc. Warranty Service Department.
Top Innovations, Inc. will repair or replace, at its option. This warranty gives you
specific legal rights and may have other rights, which may vary from state to state.
Performance of any obligation under this warranty may be obtained by:
1. Call (800) 711-6617 for Return Authorization Number before returning for
repair. Failure to obtain a Return Authorization Number will cause a delay in
warranty and out-of-warranty service requests.
2. Include copy of purchase receipt.
3. Include your name, address, telephone number, and Return Authorization
Number on returned package.
Please send product postage-prepaid to:
TOP INNOVATIONS, INC.
WARRANTY SERVICE DEPARTMENT
6655 TROOST AVE.
KANSAS CITY, MO 64131
Should there be any missing or defective parts or accessories, please contact Customer
Support. In most cases, it is not necessary to return the entire unit. We can ship most
parts directly to your door.
Upon expiration of 1 year limited warranty, you will be advised of the cost of repair
before any servicing is done, unless you enclose a note indicating that you would like us
to proceed with repairs.
If you need to request warranty service, or have any questions about coverage under this
warranty, please visit the Warranty Service Request page on our Web site
www
.topinnovations.com. You may also contact the Warranty Service Department by
telephone at (800) 711-6617 or (816) 584-9700, or e-mail
customerservice@topinnovations.com
Please have your product serial number ready before contacting Warranty Service
Department. The serial number is located on the back or bottom of your unit.
.
Top Innovations, Inc.
15
Loading...