Topens PW 302, PW 502, PW802 User Manual
Dual Swing Gate Opener
VER 20b
C030404
Please read and follow all warnings, precautions and instructions before
User’s Manual
Model:
PW 302/502/802
TOPENS Website
http://www.topenstool.com/
★
installation and use.
★ The gate opener could be powered by either the 24VDC AC-DC power supply
which is included in the package or 2 PCS 12VDC batteries (connected in series,
at least 12AH, NOT INCLUDED) which can be charged by solar panel.
★ Never connect the solar panel to the control board directly to charge the battery.
★ Periodic checks of the opener are required to ensure safe operation.
★ Save this manual.
Table of Contents
Safety Installation Information ....................................................................................................................... 1
PW302 Parts List ........................................................................................................................................... 2
PW502/PW802 Parts List .............................................................................................................................. 3
Accessories Parts (Included in some models, refers to the actual package) ....................................................... 3
Optional Accessories Parts List (Available at TOPENS Store) ............................................................................. 4
Tools Needed: ............................................................................................................................................... 4
Technical S peci fications & Features .............................................................................................................. 4
Installation Overview ..................................................................................................................................... 6
Preparation for Installation ............................................................................................................................ 6
Install the Gate Opener on the Gate .............................................................................................................. 7
Mounting of the Control Box ........................................................................................................................ 12
Connection of the Power Supply ................................................................................................................. 12
Connection of the Control Board ................................................................................................................. 14
How to Program the Remote to the Opener ................................................................................................ 16
How to Erase All the Remote Codes ........................................................................................................... 16
How to Use the Remote to Operate Your Gate Opener ............................................................................... 17
Wireless Keypad Programming ................................................................................................................... 17
Adjusting the Limit Switch ........................................................................................................................... 18
Setting of the Control Board ........................................................................................................................ 18
Maintenance ................................................................................................................................................ 20
Status of LED(s) & Trouble Shooting ........................................................................................................... 21
Safety Installation Information
1. READ and FOLLOW all inst ruction.
2. The gate opener is intended for use with Class I
vehicular swing gates.
Class I denotes a vehicular gate opener (or system)
dwellings, or a garage or parking area associated
therewith.
Install the gate opener only when the opener is
appropriate for the construction and the usage class of
the gate.
3. Gate opening system designers, installers and
users must take into account the possible hazards
associated with each individual application. Improperly
designed, installed or maintained syst ems can create
risks for the user as well as the bystander. Gate
system design and installation must reduce public
exposure to potential hazards. All exposed pinch
points must be eliminated or guarded.
4. A gate opener can create high levels of force
during normal operation. Therefore, safety features
must be incorporated into every installation. Specific
safety features include safety sensors.
5. The gate must be properly installed and work
freely in both directions prior to the install ation of the
gate opener.
6. The gate must be installed in a location so that
enough clearance is provided between the gate and
adjacent structure when opening and closing to
reduce the risk of entrapment. Swinging gates shall
not open into public access areas.
7. The opener is intended for use only on gates used
for vehicles. Pedestrians must be supplied with a
separate access opening. The pedestrian access
opening shall be designed to promote pedestrian
usage. The pedestrian access shall be located such
that persons will not come in contact with the moving
vehicular gate.
use on any pedestrian gate. Pedestrians must be
supplied with a separate pedestrian acces s.
9. For an installation utilizing non-contact sensors
(safety sensors), see product manual on the
placement of non-contact sensors (safet y sensors) for
each type of application.
a. Care shall be exercised to reduce the risk of
nuisance tripping, such as when a vehicle trips the
safety sensor while the gate is still moving.
b. One or more non-contact sensors (safet y sens ors)
shall be located where the risk of entrapment of
obstruction exists, such as the perimeter reachable by
a moving gate or barrier.
10. Never mount any device that operates the gate
opener where the user can reach over, under, around
or through the gate to operate the controls. Controls
are to be placed at least 6’ (1.8m) from any part of the
moving gate.
11. Controls intended to be used to reset an operator
after 2 sequential activations of the entrapment
protection device or devices must be located in the
line of sight of the gate, or easily accessi ble controls
shall have a security feature to prevent unautho rized
use. Never allow anyone to hang on or ride the gate
during the entire travel of the gate.
12. Each gate opener is provided with two safety
warning placards. The placards are to be installed on
the front and back of the gate where they are pl ainly
visible. The placards may be mounted using cable ties
through the four holes provided on each placard.
All warning signs and placards must be installed
where visible in the area of the gate.
8. Pedestrians should never cross the pathway of a
moving gate. The gate opener is not acceptable for
1
13. To AVOID damaging gas, power, or other
Rev 20a
underground utility lines, contact underground utility
locating companies BEFORE digging.
PW302 Parts List
SAVE INSTRUCTION.
14. Do not permit children to play on or around the
gate and keep all controls out of their reach.
2
PW502/PW802 Parts List
Rev 20a
Accessories Parts (Included in some models, refers to the actual package)
3
Optional Accessories Parts List (Available at TOPENS Store)
·
·
·Hacksaw or Heavy Duty Bolt Cutters
·
Current:
1.5A
2A
3A
Actuator speed:
16mm/s（0.6 in/s）
Max. actuator travel:
385mm（15.2 in）
Ambient Temperature:
-20
-4°F to 122°F)
Rev 20a
Tools Needed:
Power Drill ·Tape Measure ·Open End Wrenches - 14# &17# or Adjustable Wrenches
Wire Strippers ·C-Clamps - small, medium, and large ·Level
Phillips Screwdriver ·An extra person will be helpful
Technical Specifications & Features
Specifications
PW302 PW502 PW802
Input: 100-240V~ 50/60Hz
Motor voltage: 24VDC
Power:
2×30W 2×50W 2×80W
℃~ +50℃ (
Protection class: IP44
4
Features:
·
·
·
·
·
·
·
·
·
·
Soft start and soft stop
Emergency release key in case of power failure
Fast selecting push/pull to open
Stop in case of obstruction during gate opening.
Reverse in case of obstruction during gate
closing.
Built in adjustable auto-close (3-120 seconds)
· Built in max. Motor running time (MRT) for
multiple safety protection (40 seconds)
Reliable electromagnetism limit for easy
adjustment
Can be equipped with a wide range of
accessories
Adjustable opening/closing interval between
master and slave gate
Easy to install, and minimum maintenance
requirement
5
Installation Overview
NOTE:
Rev 20a
Preparation for Installation
There are two installation types for the gate opener, Pull-to-Open and Push-to-Open.
In the Push-to-Open instal lation, gate opens out from the property. A Push-To-Open Bracket (PSO part) is
required to be used for each gate.
The gate opener is mounted to the gate and to the gate post. Both round and square posts can be used
because the Post Brackets are curved. When mounting the Post Brackets, use bolts long enough to pass
through the entire post. M10 x 200 bolts are incl uded. Concrete anchors are not provided.
When mounting the Post Brackets to wooden posts, a larger-size washer or metal plate should be used
between the bolts and the wooden post to ensure the stabi l ity of the fastening hardware. If the post is smaller
than 6" diameter or square, it should be made of metal and set in cement to ensure its stability.
Ensure the gate does not open into public areas.
6
Loading...