Page 1
IMPORTANT
Although light body and battery are water-resistant (under
normal weather conditions of rain, etc..) never intentionally
submerge them under water.
The battery used in the WhiteLite™ HP Mega 10W is 3.7 volts.
Never attempt to alter this lighting system. Never use this
battery with any other lighting or electrical system.
Never attempt to disassemble the battery.
If battery pack is dropped, battery case may be cracked and a
short circuit may occur. Replace battery pack immediately.
The battery has unique characteristics. The light output will
remain high until the battery runs down then drops suddenly.
Always pay attention to the charge remaining and take
precautions by carrying a spare battery.
The battery charger is for indoor use only. After charging the
battery, be sure to unplug it from the home power outlet.
If the light body or parts become dirty, gently clean with a soft
towel using mild soap and water. Never use harsh chemicals
to clean the lighting system as damage to housings will occur.
When connecting and disconnecting the plug and socket hold
the connector ends only. Do not attempt to connect or
disconnect the plug/socket interface by pushing or pulling on
wires or serious damage to wires and connectors will occur.
After long periods of non-use, the battery will lose charge.
Always charge the battery fully before each use and storage.
Maintain the battery by charging it every three months and
storing it in a cool, dry place to prevent from decreasing its
lifespan. 3 to 5 charging cycles are needed to attain full capacity
after a long period of non-use.
WARNING
Pacemaker users should never use this device.
The light body becomes extremely hot when used for long
periods of time. Never touch the body or lens until it has
thoroughly cooled, otherwise injury may occur.
Never look directly into the light when it's turned on.
It may harm your vision.
Do not use this light improperly on public roads. The light
output is equal to automobile halogen bulbs. Adjust the light
accordingly so as not to blind oncoming traffic.
If the light unit, cord or battery pack is damaged, discontinue
use immediately. A hazardous condition may result due to
the high voltage system.
Never short-circuit the terminals of the battery pack or the
plug of the components.
Safely and properly dispose of the old Li-ion batteries
according to your local regulations.
Never place this lighting system within a child's reach.
Use only the supplied battery charger for this system.
Night riding is inherently more dangerous than daylight
riding. For your safety and the safety of others, Topeak asks
that you use extreme caution when using this or any other
light source while riding at night.
Stay alert and ride safely while using your WhiteLite
Mega 10W.
If the lighting system turns off automatically, DO NOT
attempt to turn on the lighting system again, or damage
and/or decreased battery life may occur.
™
HP
WhiteLite™ HP Mega 10W
WhiteLite™ HP Mega 10W is equipped with standard
mounting parts for Handlebar, Battery and Helmet.
Please read all instructions before first use.
User's Guide
Battery: Li-ion 3.7 V
GB
D
F
E
I
J
KR
CH
SPARE PARTS
Light Unit
Art no. TMS-SP68
Helmet Mount Unit Art no. TMS-SP36
Battery Charger
Art no. TMS-SP69
Battery Pack
Art no. TMS-SP67
Rubber Strap Art no. TMS-SP06
SPECIFICATIONS
Bulb: 10W LED, 900 Lumens (Max)
Battery: Lithium ion rechargeable battery 3.7 V 10400 mAh
Recharge/ Discharge Number of Times:
at least 300 (until rated capacity drops to 50%)
Operation Temperature: -20˚C - 45˚C (-4˚F ~ 113˚F)
Storage Temperature: -20˚C - 60˚C (-4˚F ~ 140˚F)
Charger:
Input: Voltage: AC 100-240V, 50/60Hz
Current: 0.7A Max
Output: Voltage: 4.2V DC
Current: 3A Max
Charging Time: 5~6 hours
Operating Temperature: 0˚C ~ 40˚C (32˚F ~ 104˚F)
Storage Temperature: -20˚C ~ 60˚C (-4˚F ~ 140˚F)
Topeak products are available only from professional bicycle shops.
Please contact your nearest Topeak authorized bicycle dealer for any questions.
G
For customers in the USA, call: 1-800-250-3068 Website: www.topeak.com
B
8
Serial No.:
Register your light system at
www.topeak.com
WARRANTY
1-Year Warranty: All mechanical components
(light body, covers, mounts and fasteners) against
manufacturer defects only.
90-day Warranty: All batteries and chargers against manufacturer
defects only.
60-day Warranty: All bulbs against manufacturer defects only.
Warranty Claim Requirements
To obtain warranty service, you must have your original sales receipt.
Systems returned without a sales receipt will assume that the warranty
begins on the date of manufacture. All warranties will be void if lighting
system is damaged due to rider crash, abuse, system alteration,
modification, or used in any way not intended as outlined in this
operating manual.
* The specifications and design are subject to
change without notice.
Copyright © Topeak, Inc. 2011
M-TMS060-GB 08/11
Power Controller
Press and hold for
3 seconds
to turn on or off
Thank you for purchasing the Topeak WhiteLite™ HP Mega 10W.
Designed for high performance night cycling. This is a unique high
power 3.7 volt lighting system. Before operating, thoroughly familiarize
yourself with this manual so that you understand the light's safe and
correct operation. Please keep this manual for further reference.
Power Level
Indication
10W
Blue
5W
Green
Blinking
Red
Before first use, the battery pack must be fully
charged. (Please follow the instructions on
BATTERY PACK CHARGING.) When the battery pack
has not been used for a long period, operating time
will shorten due to self-discharging properties of
the Li-ion battery.
Mount on Handlebar
1
Mount on Battery
2
Mount on Helmet
3
MOUNTING POSITION
G
B
1
Page 2
DETAILED PARTS DESCRIPTION
MAIN UNITS
1-1 1-2
1-3
1-4
1-5
HANDLEBAR MOUNT
2-1 2-3
2-2
3-1
3-2
3-2a
ACCESSORIES FOR MOUNTING ON HANDLEBAR
4
5-1
5-2
3-2b
6-2
POWERPACK OPERATION
Run-time reference: 3 hours at 10W in fully-charged condition.
In order for the battery pack to determine the correct light unit, the battery must be securely connected to the light unit before
being turned on. Press and hold the power controller for 3 seconds to turn on the light. Choose your desired power level by pressing
the power controller.
Total Run Time
Power Level
10 W
1
5 W
2
Blinking
3
* Standard Operating Temperature: 15˚C~25˚C (59˚F~77˚F)
LEDMode
Blue
Green
Red
3 hrs.
6 hrs.
24 hrs.
Note:
In case light does not turn on, retry turning on the light.
If the ambient temperature is extremely high or low (even within
the operating temperature range), the operating time may be
shorter than the standard time due to characteristics of the battery.
POWER AND SAFETY TIME RESERVE TANK INDICATORS
6-36-1
Power Controller
Press and hold
for 3 seconds
to turn on or off
WhiteLite™ HP Mega 10W includes a Safety Time Reserve tank that
provides up to 30 minutes of additional burn time at 2.6W. The light
will shut off automatically after RED power-indicator blinks for 1
minute. For continued use, charge the battery or use a spare battery.
Note:
Battery run times are approximate. Run times will vary due
to usage patterns, temperature, and battery condition.
BATTERY MOUNT
MAIN UNITS
1. Light Unit (#TMS-SP68)
1-1 Light Body
1-2 Power-Controller
1-3 Battery Pack Connecting Plug
1-4 M3 bolt
1-5 Handlebar Bracket
2. Battery Pack (#TMS-SP67)
2-1 Socket
2-2 Battery with Velcro Strap
2-3 Rubber Pad
3. Charger
3-1 Power Cord
3-2 Battery Charger (#TMS-SP69)
3-2a Socket
3-2b Battery Pack Connecting Plug
G
B
2
ACCESSORIES FOR MOUNTING ON BATTERY
ACCESSORIES FOR MOUNTING ON HELMETHELMET MOUNT
9-1
9-2
ACCESSORIES FOR MOUNTING ON H/BAR
4. Triangle Rubber Pad
5. Rubber Strap Unit
5-1 Rubber Strap x 2 (for ø 22.2~ø 25.4)
5-2 Rubber Strap x 2 (for ø 25.4~ø 31.8)
6. Cable Unit
6-1 Extension Cable
6-2 Socket
6-3 Connecting Plug
ACCESSORIES FOR MOUNTING ON BATTERY
7. BATTERY LIGHT BRACKET
8. Adjusting Nut (Additional)
7
8
10-1
9-3
ACCESSORIES FOR MOUNTING ON HELMET
9. HELMET LIGHT BRACKET Unit (#TMS-SP36)
9-1 Light Holder
9-2 Helmet Band
9-3 Velcro Strap x 2 pcs
10. Cable Unit
10-1 Extension Cable
10-2 Socket
10-3 Connecting Plug
10-2
10-3
10W
App. 180 min
5W
App. 360 min
Blinking
App. 1410 min
Off
Blinking App. 1 min Blinking App. 1 min
Blinking
3 times
Blinking App. 1 min Blinking App. 1 min
Blinking
3 times
2.6W S.T. Reserve
App. 30 min
Note:
The light body will be extremely hot in10W mode.
If the temperature of light body has been 90ºC,
the light will turn to 5W mode automatically after
blinking 6 times. Press the power-controller twice
to return to 10W mode.
2.6W S.T. Reserve
App. 30 min
2.6W S.T. Reserve
App. 30 min
Blinking App. 1 min
Blinking
6 times
Blinking
6 times
Blinking
6 times
Total Burn Time at
Shut
off
DON'T TOUCH
The light body is
extremely hot in
10W mode and may
cause bodily injury
2.6W
24
hours
if touched.
Total Burn Time at
Shut
off
Total Burn Time at
Shut
off
3.5
6.5
10W
hours
5W
hours
G
B
3
Page 3
MOUNTING INSTRUCTIONS
MOUNT ON HANDLEBAR
1. Mount Battery on Stem
2. Mount Light on HandleBar
Without Triangle
Rubber Pad
With Triangle
Rubber Pad
You can install the light with Triangle
Rubber Pad for proper mounting position.
WARNING
• Fits stem lengths > 80mm
• NOT for adjustable stem
• NOT for the angle of stem <90º
> 90º
Cut the rubber
pad for proper length.
OPTIONAL MOUNTING POSITION FOR BATTERY
Extension Cable
Rubber Straps
for ø 22.2~ø31.8
Release the original rubber pad first.
Install the triangle rubber pad.
WARNING
Make sure the connecting plug has
been plugged in socket completely.
Use 3mm Allen key to
adjust and tighten.
MOUNT ON BATTERY
Use 3mm Allen key to
adjust and tighten.
G
B
4
2mm Allen Key
2mm Allen Key
3mm Allen Key
Use 3mm Allen key to
adjust and tighten.
Fasten the Velcro Strap on stem.
Snap light unit plug and battery socket together securely.
WARNING
Make sure the connecting
plug has been plugged in
socket completely.
G
B
5
Page 4
MOUNT ON HELMET
Install Light Unit
3mm Allen Key
3mm Allen Key
Helmet Band
BEAM ANGLE ADJUSTMENT
Switch on light in darkened conditions on a flat surface and adjust
the beam angle vertically to desired position. It can also be pivoted
15˚ laterally. To adjust beam, loosen the adjusting bolt. Position light
unit to reach the desired beam angle and re- tighten the bolt securely.
In addition to its high brightness, the beam is
widely diffused. If you use this light on public
roads, be sure to adjust the angle downward
so as not to blind oncoming traffic.
BATTERY PACK CHARGING
1.
Be sure battery charger input voltage is correct.
2.
Connect power cord to battery charger and battery charger
plug to battery pack before connecting to home power outlet.
3.
The battery charger LED will be RED during charging.
4.
The battery charger LED will turn GREEN when battery is fully
charged.
5.
The battery charger LED will not illuminate if the charger is faulty.
6.
Disconnect the battery charger power cable from home power
outlet when the battery is removed.
7.
It is normal for the battery charger and battery to become hot
during charging. Please use caution when charging battery.
8.
After battery is fully charged, unplug the battery charger.
the Home
Power Outlet
Standard charging time
5 - 6
hours
Use 3mm Allen key to
adjust and tighten.
Main Unit Installation
Snap light unit plug and extension cable socket together securely.
Snap extension cable plug and battery socket together securely.
Put Battery Pack in backpack or in a pack.
Adjust beam angle properly.
3
Topeak Air BackPack
Art No. TABP-1M
G
B
6
WARNING
Make sure the connecting
plug has been plugged in
socket completely.
2
Use to fix extension cable.
1
Use 3mm Allen key to
adjust and tighten.
4
Note:
If the light fails to turn on after several tries, charge the battery to full
capacity.
The standard charging time is 5 to 6 hours.
(The charging time and operating time may vary depending on ambient
temperature.)
Li-ion batteries may take 3 to 5 charging cycles to attain full capacity.
If the battery does not give the proper run time after being fully charged,
replace with a new battery pack.
LIGHT BODY MAINTENANCE
2mm Allen Key
Loosen the screws on both sides.
Remove the light cap.
Note:
WARNING
Before removing light cap
mounting screws, make sure
bulb and light body are cool.
If the light body or parts become dirty, gently
clean with a soft towel using mild soap and
water. Never use harsh chemicals to clean
the lighting system as damage to housings
will occur.
Do not place battery charger in a damp or dusty
location or areas affected by oil fumes or steam.
Do not open battery charger case.
Battery charger is for indoor use only.
Avoid electrical shock.
Do not leave battery connected to charger over
48 hours continuously.
WARNING
Never remove lens screws.
G
B
7
Loading...