Topeak PanoBike TPB-CS01 User Manual
Tighten the Wheel Magnet onto spoke and align with sensing point on sensor.
3
Unscrew the wheel magnet
to install on spoke.
Pre-t Sensor and Rubber Bracket on left rear
chainstay (non-drive side) and trim excess rubber
from bracket. Insure the Topeak logo is facing up.
Install zip ties loosely to allow sensor placement.
2
Top View
GB
Tech: Bluetooth® Smart super low energy technology
Battery Lifetime (approx): 1800 hours
(5 years with 1hr/day use)
Battery: CR2032 x 1 pc (included)
Transmisson Range: <10 meter (33 ft)
Waterproof: IPX 7
Weight: 21g / 0.74 oz
Operating temperature: -10º C ~ 50º C (14º F~122º F)
SPECIFICATION
Cadence Sensor
Sensing Point
Speed Sensor
Sensing Point
Cadence Magnet
Holder
6mm 8mm
Zip Tie
Rubber
Bracket
Cadence Magnet Set (A)
for pedal axle hexagon socket
Wheel Magnet Set
Rubber Bracket Set
Cadence Magnet Set (B)
for crankarm
Cadence
Magnet
Zip Tie
Cadence
Magnet
Sticker
Sync to PanoBike App and other Apps with Bluetooth® Smart (BLE 4.0) connection program.
INSTALLATION
TIPS : Proper distance between Sensor and Magnet : < 30mm
Install Cadence Magnet on left crankarm near
pedal as shown. Do not tighten zip ties
completely to allow magnet placement.
Cadence Magnet Set (B)
OPTION
A
OPTION
B
Cadence
Magnet
Cadence
Magnet
Cadence Sensor
Sensing Point
Cadence Sensor
Sensing Point
Top View
Top View
1
For Round Spokes
For Bladed Spokes
User's Guide
PanoBike Speed & Cadence Sensor
IMPORTANT NOTE
Align Cadence Magnet
with Cadence Sensor
Sensing Point as shown
to insure magnet does
not interfere with
Speed Sensor.
IMPORTANT NOTE
Align Wheel Magnet with Speed
Sensor Sensing Point as shown to
insure magnet does not interfere
with Cadence Sensor.
IMPORTANT NOTE
Align Cadence Magnet with Cadence Sensor
Sensing Point as shown to insure magnet
does not interfere with Speed Sensor.
Speed Sensor
Sensing Point
Preset suitable 6 mm or
8mm Cadence Magnet Set.
Cadence Magnet Set (A)
(6 mm or 8 mm)
6 mm 8 mm
Art no. : TPB-CS01
GAP < 30 mm (1.2")
GAP <
30 mm (1.2")
Pair with PanoBike App
2-year Warranty: All electronic and mechanical components against manufacturer defects
only. Batteries are not covered under any implied warranty.
Warranty Claim Requirements
To obtain warranty service, you must have your original sales receipt. Items returned
without a sales receipt will assume that the warranty begins on the date of manufacture.
All warranties will be void if the product is damaged due to user crash, abuse, system
alteration, modication, or used in any way not intended as described in this manual.
* The specications and design are subject to change without notice.
Please contact your Topeak dealer with any questions.
For USA customer service call: 1-800-250-3068
www.topeak.com
Copyright © Topeak, Inc. 2012
WARRANTY
CAUTION
1. The Sensor and hardware can be
used in the rain but should not be
used underwater.
2. Do not dissassemble the Sensor
and hardware.
3. Check relative positions and gap
between sensor and magnets
periodically.
4. Do not use harsh chemicals to
clean the Sensor and hardware.
5. Remember to pay attention to
the road while riding.
TROUBLE SHOOTING
1. Why can’t I connect the sensor with PanoBike App?
• Make sure the Bluetooth® system in your smartphone has been
open.
• Is the battery exhausted? Replace battery.
2. Display is slow?
• Is the temperature below -10ºC (14ºF)? The unit will return normal
state when the temperature rises.
3. No current speed or incorrect data ?
• Make sure the magnets are aligned to pass by the sensor as the
crankarm and wheel spin.
RECHECK TO INSURE CADENCE & WHEEL MAGNETS DO NOT INTERFERE WITH EACH OTHER’S SENOR
4 5
Adjust angle and position of sensor to achieve recommended
magnet distances and aligning sensing points.
* Bluetooth® is a registered trademark of Bluetooth SIG, Inc.
* iPhone is a registered trademark of Apple Inc.
* App Store is a service mark of Apple Inc.
User's Guide
PanoBike Speed & Cadence Sensor
1
Turn the crankarm clockwise
to check the Current
Cadence (CAD) data displays
correctly with no Current
Speed (SPD) data.
Pair with PanoBike App.
Turn the crankarm counterclockwise
to make sure the Current Cadence (CAD) and Current Speed (SPD)
data displays correctly without interfering with each other. Tighten all
zip ties and wheel magnet after successful pairing. Trim zip tie excess.
CHANGING BATTERY
NOTE:
Install the sensor
battery before
rst use.
+
-
CR2032
Operation Time up to
1800 hrs. / 5 yrs.
* 5 years with 1hr/day use
RELEVANT ACCESSORIES
PanoBike Heart Rate Monitor
Art No. TPB-HRM01
RideCase
Art No. TT9832B, TT9832W
(works with iPhone 4/4S)
TT9833B, TT9833W
(works with iPhone 5)
2
Spin the wheel
counterclockwise to check
the Current Speed (SPD)
data displays correctly
with no Current Cadence
(CAD ) data.
IMPORTANT NOTE
After pairing with PanoBike App
successfully, make sure the Sensor
is installed and tightened securely
on left rear chainstay by using
needle nose pliers before trimming
excess zip tie.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment o and on, the
user is encouraged to try to correct the interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modications not expressly approved by the party responsible
for compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.
FCC STATEMENT
Art no. : TPB-CS01
Loading...