Tonika Electronics Technology TA-387 User Manual

Size:148x210MM

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

POWER SOURCE

This unit can be powered by either AC power or built-in rechargeable battery.

PORTABLE BLUETOOTH SPEAKER

WITH AMPLIFIER

Model name:TA-387

19 IC warning:

Before using the unit, be sure to read all operating instructions carefully precautions and may not pertain to your unit For example, this unit may not have the capability to be connected to an outdoor antenna.

1. Read these instructions All the safety and operating instructions should be read

before the product is operated.

2. Keep these instructions The sately and operating instructions should be retained

for future reference.

. Please note that these are general

AC Operation:

To operate the unit using AC power:

1. Connect the small plug from the supplied AC power cord to the AC Jack on the rear of unit.

2. Plug the AC power cord to the AC wall outlet having AC 120V~, 60Hz.

3. Press the Power Switch on the rear of unit to POWER ON position to power on the unit.

4. When finished, press the Power Switch to POWER OFF position to shut off the unit.

TO AC IN JACK

To Wall Outlet

CHARGE

Operation by Built-in Rechargeable Battery:

The unit has a built-in rechargeable battery, recharge it before use as below:

1. Connect the small plug from the supplied AC power cord to the AC Jack on the rear of unit.

2. Plug the AC power cord to the AC wall outlet having AC 120V~, 60 Hz.

3. Press the Power Switch on the rear of unit to CHARGE position to start charging, the Power ON and Charging indicators on the top of unit will light. When the battery is fully charged, the Charging indicator will turn off.

4. After charge, disconnect the AC power cord from wall outlet. Press the Power Switch on the rear of unit to POWER ON position to power on the unit. (If the AC power cord is connecting to wall outlet, the unit will select to using AC power automatically).

5. When finished, press the Power Switch to POWER OFF position to shut off the unit.

Notes:

A. In Power on mode, the battery will not be recharge. Always press the Power Switch to CHARGE position to recharge the battery. B. For charging first time, charge it approximate 10 hours. C. Recharge and store the device within the temperature range to 5°C~35°C (40°F~95°F). D. Do not overcharges (longer than 24 hours). Excessive charging or running the unit until battery goes empty will damage battery. Battery life will be extended if you keep the battery fully charge. E. Battery life naturally shortens slowly over time. F. The rechargeable battery incorporated in this product is not user replaceable. G. If long period of time will not use, unplug the AC power cord from wall outlet.

1. Power Indicator

2. BT (Blue Tooth) Indicator

3. FM Indicator

4. AUX 1 Indicator

5. AUX 2 Indicator

6. Charging Indicator

7. SOURCE Button

8. SCAN / 　　　(Radio Scan/Play-Pause)　Button

9. CH - /　　　　(Channel Down/Skip Backward) Button

10. CH + / (Channel Up/Skip Forward)　Button

11. EQ (Equalizer) Button

12. Volume Knob

13. MIC VOL (Microphone Volume) Knob

14. MIC ECHO (Microphone Echo) Knob

15. AUX 1 Jack

16. MIC (Microphone/Electric Guitar) Jack

17. Carry Handle

18. AUX 2 Jacks

12 13 14

8 109 11 6 5 4

20 19

CHARGE

OPERATION:

OPERATION: General:

1. Power on the unit as previous procedures.

2. Press the SOURCE Button repeatedly to select the source as desire (When change the input source from BT or to BT mode, it needs take approximate 1 second, please wait.).

3. Turn the VOL (Volume) Knob to adjust the volume level as desire.

4. Press the EQ (Equalizer) Button repeatedly to set the preset equalizer mode as desired. Notes: ~ EQ is operation in BT mode only. ~ To reset the EQ mode to normal mode, power off then power on the unit.

5. When finished, press the Power Switch to POWER OFF position to power off the unit. Note: If long period of time will not use the unit, unplug the AC power cord from wall outlet.

BT (Blue Tooth):

1. Power on the unit as previous procedures.

2. Press the SOURCE Button repeatedly until the BT Indicator is light.

3. If this is the first time to use BT or re-pairing the unit to a new BT device, pairing the unit to external BT device as bellows: i. Power on the external BT device and enter to searching mode. ii. Start pairing as the on screen instructions on the external BT device. iii. After paired, the BT Indicator will stop blinking (For details pairing procedures, please refer to the user’s manual of your BT device.). 　　　Notes:

● When the external BT device searched the unit, our model number “CHT 936” will

appears on the display of external BT device.

● Pairing code “0000” may need to enter.

4. Normal operation after paired: i. Turn on the BT function of the external BT device. ii. Power on the unit and press the SOURCE Button repeatedly until the BT Indicator is light and blinking. iii. Wait a few seconds until the unit paired to the external BT device automatically. (The BT Indicator will stop blinking). iv. Plays the music in the connected BT device as usual.

Radio:

1. Power on the unit as previous procedures.

2. Press the SOURCE Button repeatedly until the FM Indicator is light.

3. If first time to use (or replaced the unit in a new location), press the SCAN/ Button. The unit will start searching and stored all available FM stations automatically. (Up to 30 stations can be stored).

4. After scanning, press the CH +/ or CH -/ Button repeatedly to select the desired stored FM station.

AUX 1:

1. Connect the external Audio Device (such like MP3 Player; CD Discman; iPod/iPhone/iPad … etc) by the supplied audio connection cable as the figure below:

AUX 1

ipad, discman

2. Power on the unit as previous procedures.

3. Press the SOURCE Button repeatedly until the AUX 1 Indicator is light.

4. Plays the audio files in the connected Audio device as usual. (Note: Make sure the volume level of the connected device is in high level. Otherwise, sound from this unit is weak.)

AUX 2:

1. Connect the external AV Device (such like TV/DVD/VCR/DVR … etc) as the figure below:

CHA

RGE

2. Power on the unit as previous procedures.

3. Press the SOURCE Button repeatedly until the AUX 2 Indicator is light.

4. Plays the video files in the connected AV device as usual. (Note: Make sure the volume level of the connected device is in high level. Otherwise, sound from this unit is weak.)

Microphone:

1. Connect the supplied External Microphone to the MIC Jack on the top of unit as the figure below:

Dynamic Microphone Included

2. Power on the unit and selected the input source as previous procedures.

3. Turn the MIC VOL (Microphone Volume) Knob to adjust microphone volume level as desire.

4. Turn the MIC ECHO (Microphone Echo) Knob to adjust echo effect as desire.

5. Speak or sing into the microphone. If fit back sound (high frequency audio noise) was heard from the speaker, reduce the microphone volume or keep the microphone away from speaker.

Electric Guitar:

1. Connect the Electric Guitar (not supplied) to the MIC Jack on the top of unit as the figure below:

Electric Guitar (not Included)

2. Power on the unit and selected the input source as previous procedures.

3. Turn the MIC VOL (Microphone Volume) Knob to adjust the sound level of Electric Guitar as desire.

4. Turn the MIC ECHO (Microphone Echo) Knob to adjust echo effect as desire.

5. Plays the Electric Guitar as usual. If fit back sound (high frequency audio noise) was heard from speaker, reduce the microphone volume.

Carry Handle:

Press the button on the handle then pull it out. When finished, press the button then push it back as the figure below:

TROUBLESHOOTING GUIDE

Check the follows before requesting service:

SYMPTOM POSSIBLE CAUSE

No power had not

No Sound

Sound distortion Volume level too high

BT not function The external BT device too

Built-in battery cannot be recharge.

AC Power Cord

plug in the unit or wall outlet

POWER Switch is in OFF position

Built-in recharge battery consume

Volume in minimum position Rise volume level by turning

The connected device is not in playback mode Sound output of the connected device weak Input source incorrect

Volume level of the connected device too high the connected device

far from the unit

The Power Switch has not press to CHARGE position.

POSSIBLE SOULTION Plug it to the wall outlet and the

properly

unit

Press the POWER Switch on the rear of unit to POWER ON position

Recharge the built-in battery as page 5

VOL (Volume) + Knob

the

Plays the audio/video files in the connected Rise the volume level of the connected device

Set the input source as the connection

Reduce the volume level by

turning the

Reduce the volume and/or bass level of

Place the external BT device close to the unit

Press the Power Switch to CHARGE position.

device as usual

VOL (Volume) - Knob

GENERAL SPECIFICATIONS:

Power Source: ……………………………………………………AC 120V~, 60Hz; 0.5A Radio FM Band Coverage: ………………………………………………… 87.5-108MHz BT Effective Range: ………………………………………… Up to 32 Feet in open area Audio Power: ……………………………………………………………………………20W

Accessories:

1 x User’s Manual 1 x Audio Connection Cable with 3.5mm Stereo Mini Plugs 1 x AC Power Cord 1 x Dynamic Microphone

LIMITED WARRANTY

Craig warrants this product to be free from manufacturing defects in material and workmanship under normal use for a period of 90 days from date of purchase. If service is required, please return the product to the store where it was purchased for exchange; or, pack the unit in the original packing material with all accessories if applicable, a copy of your sales receipt and a Cashier’s check or Money Order for $18.00 (to cover shipping and handling costs) payable to Craig Electronics Inc. For consumers in Canada, please make sure that the cashier check or money order is redeemable through a U.S. bank. Ship your product freight pre-paid. Your unit will be repaired, replaced or if the unit can not be repaired or replaced, a refund will be forwarded to you within four weeks of receipt of your unit. Please ship your unit to:

Craig Electronics Inc.

1160 NW 163 Drive

Miami, Fl 33169

This warranty is void if the product has been: a) Used in a commercial application or rental. b) Damaged through misuse, negligence, or abuse. c) Modified or repaired by anyone other than an authorized Craig service center. d) Damaged because it is improperly connected to any other equipment. Note: This warranty does not cover: a) Ordinary adjustments as outlined in the Owner’s Manual which can be performed by the customer. b) Damage to equipment not properly connected to the product. c) Any cost incurred in shipping the product for repair. d) Damage to the product not used in the USA.

This warranty is not transferable and only applies to the original purchase. Any implied warranties, including the warranty of merchantability, are limited in duration to the period of this expressed warranty and no warranty whether expressed or implied shall apply to the product thereafter.

Under no circumstance shall Craig be liable for any loss or consequential damage arising out of the use of this product. This warranty gives specific legal rights. However, you may have other rights which may vary from state to state. Some states do not allow limitations on implied warranties or exclusion of consequential damage. Therefore, these restrictions may not apply to you.

To Obtain Service on your Product

email:service@craigelectronics.com

Printed in China CHT936_WC_E0FG1_V0US

19. POWER ON/POWER OFF/CHARGE Switch

20. AC IN Jack (AC 120V~; 60Hz)

4 5

7 8 9

VEUILLEZ LIRE AVANT DE FAIRE FONCTIONNER CET APPAREIL.

Modèle: CHT936

8 9

POR FAVOR LEA ESTE MANUAL ANTES DE UTILIZAR ESTE EQUIPO.

Modelo: CHT936