Tonika Electronics Technology TA 359 01 User Manual

1. CD Player

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC RF Exposure Information and Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body.

2. Disk Tray( Inside CD Player)

3. Open / Close Tab

4. LED Neon Lights

5. CD Display Screen

6. Standby Button

7. Play / Pause Button

8. Stop / Scan Button

9. Program Button

10. Function Button

11. Skip - / Volume - Button

12. Skip + / Volume + Button

13. Repeat Button

14. On / Off Switch

15. 5V 1A DC Input Jack

16. Aux Input Jack

17. FM Radio Antena

10 11 12 13

SCN

the control panel or the ‘Tune+/Skip+’ and ‘Tune-/Skip-’ buttons on the remote control. For a better signal, adjust the FM Antenna wire.To

Using the Retro Jukebox with CD Player Plug the DC input jack on the power adaptor into the DC in socket on the

automatically skip to the next radio station on the wavelength, press the ‘Scan’ button on the remote control.

reverse of the jukebox and then plug the adaptor into the mains power supply.Set the jukebox to ‘Standby’ mode by sliding the ‘On/Off’ switch to ‘On’. The standby indicator light will illuminate.To turn on the jukebox, press and hold the ‘Standby’ button on the control panel or press the ‘Standby’ button on the remote control.Press the ‘Function’ button on the control panel or the ‘Source’ button on the remote control to change between the CD player,Aux and FM radio functions.To adjust the volume,

REPPROG

DC 5V

ANT

OFF ON

AUX IN

OFF ON

DC 5V

ANT

AUX IN

use the ‘Skip +/- Volume+’ and ‘Skip-/Volume- ’ buttons on the control panel or use the corresponding buttons on the remote control. The volume will be shown on the CD display screen.Turn the LED neon lights on and off by pressing the ‘LED On/Off’ button on the remote control. Press and hold the ‘Standby’ button on either the control panel or the remote control to set the jukebox to standby.To turn off the jukebox completely, slide the ‘On/Off’ switch on the reverse of the unit to ‘Off’.

Bluetooth Press the ‘Function’ button on the control panel or the ‘Source’ button on the remote control until the CD display screen shows ‘BT’.Pair the Bluetooth compatible device with the jukebox by selecting‘CHT955’ from the listed devices.Tracks can be played and skipped using either the Bluetooth compatible device or the remote control.

Aux. Connect a 3.5mm cable to Aux in jack and the other end to an MP3 player or other audio source.Press the ‘Function’ button on the control panel or the ‘Source’ button on the remote control until the CD display screen shows‘AU.’ Tracks can be played and skipped using the controls on the connected device.

CD Player

OPEN/CLOSE

Carefully pull the ’Open/Close’ tab at the top of the disk tray to open the CD Player. Insert the CD to be played with artwork facing forwards. Gently press the CD into the disk tray and then close the CD player. Press the ‘Function’ button on the control panel or the ‘Source’ button

DC 5V

ANT

OFF ON

AUX IN

OFF ON

DC 5V

ANT

AUX IN

ＩＲ

ＬＥＤＬＥＤ

SCN PROG

REPFUNCTION

on the remote control until the CD display screen shows‘—’; this will then go on to display the track number, for example ‘1’. Tracks can be played and skipped using either the control panel or the remote control. The CD display screen will show the track number once a CD is playing.

Care and Maintenance Before attempting any cleaning or maintenance, ensure that the jukebox is turned off the mains power supply and has been unplugged.Wipe down the jukebox with a soft, damp cloth and dry thoroughly.Do not use abrasive cleaning solvents to clean the jukebox.Do not immerse the jukebox in water or any other liquid.Do not expose the remote control to extremely high or low temperatures, as this may destroy the battery.

FM Radio

Press the ‘Function’ button on the control panel or the ‘Source’ button on the remote control until the FM radio indicator light illuminates. When in FM status, it will turn into green light.Tune the FM radio to the desired wavelength using the ‘Skip+/Volume+’ and ‘Skip-/Volume-’ buttons on