Tongke Electronics T8 User Manual

SAFETY PRECAUTIONS

* This product is designed for use in moderate climates. Do not use or
install this unit where it would be exposed to direct sunlight or in
extremely hot temperatures, or near a radiator, stove or appliance that
produces heat.
* Do not take this unit into the bathroom, or near a swimming pool. Do
not use it where it would expose to water, moisture, dripping or
splashing.
* No objects filled with liquids, such as vases, should be placed on the
product.
* No naked flame sources, such as candles, should be placed on the
product.
* If water gets inside the unit. Unplug the power cord from the supply
socket and consult your dealer.
* Do not handle the power cord with wet hands. To avoid electric shock,

NEVER touch any internal parts. Repairs/Servicing should be left too a
qualified service person.

* When connecting or disconnecting from the mains supply, hold the

plug, not the cord. Pulling the cord may damage it and could be

dangerous.
* Do not drop the unit, spill liquid into it or allow objects to fall in it.
* If the unit fails to operate, disconnect from the mains and consult a
qualified service person.
* When plugged in, a very small current will flow. To save electricity

and for safety when not using the unit for an extended period of time,

it is recommended that the product is completely disconnected at the

AC mains socket.
* Do not bend the cord sharply, pull or twist it.
* Do not modify the power cord in any manner.
* Do not insert any metallic object into the unit.
* Unplug the power cord when there is the possibility of lighting.
* In case of malfunction due to electrostatic discharge just reset the

product (reconnect of power source may be required) to resume

normal operation.

1

We certify that the power supply is used as a device for

disconnecting the power distribution network, which should stay

easily accessible.

POSITIONING THE UNIT

* A minimum distance of 6 INCHES must be maintained to provide
sufficient ventilation.
* Allow adequate ventilation for the unit. Ventilation should not be

impeded by covering the ventilation openings with items such as

newspapers, table cloths, curtains etc. Do not stand it on a thick pile

carpet, or install it in a place with poor air flow.
* Place the unit on a flat even surface.
* Do not use the unit in excessively hot, cold, dusty, damp or humid
place.
* Condensation may form inside the CD player if the unit is left

anywhere warm and damp, or if you move the unit from somewhere

cold (e.g. Your car boot) to a warm room. In this case, let the unit

stand for 1-2 hours, or gradually increase the room temperature so

the unit is dry before you use it.
* Do not place it where it could be subject to vibration.
* Do not place it where it could be magnetised by a magnet or speaker

since there are magnets in the speakers, do not place tapes or

magnetic cards on them as recorded data could be erased.
* When this unit is used near a TV, the TV picture could be distorted. If

this happens, move the unit away from the TV. If this does not correct

the situation, avoid using the unit when the TV is turned on.
* Keep the CD door closed so the lens is not contaminated by dust. Do
not touch the lens.

2

SAFETY MECHANISM

This unit incorporates a safety interlock mechanism which switches the
laser beam on and off, so that when the disc holder is open, the laser
beam stops automatically.

This set employs an optical laser beam system in the CD mechanism designed with
built-in safeguards. Do not attempt to disassemble. Exposure to this invisible laser
light beam may be harmful a human eye. This is a Class 1 laser product. Use of
controls, adjustments or procedures other than those specified here in may result in
hazardous laser light beam exposure. This compact disc player should not be adjusted
or repaired by anyone except qualified service personnel. The laser mechanism in the
set corresponds to the stylus (needle) of a record player. Although this product uses a
laser pick-up lens, it is completely safe when operated according to directions.

3

LOCATION OF CONTROLS

4

FRONT VIEW

1. Turntable Cover

7. AM/FM Button

2. FM Radio Knob

8. CD Open/Close Button

3. Volume Knob; Power ON/OFF

9. Stop Button

4. Function Knob
(CD/PH/FM/AUX/BT/TAPE)

10. Play/Pause Button

5. PREV Button

11.LED Display

6. Next Button

12. CD Door

REAR VIEW

13. AUX input 14. DC IN port

22. AM/FM Antenna

TOP VIEW

15. Turntable pickup 19. Control Perch

16. Tone Arm 20. 45 RPM Adaptor

17. Speed Control Switch 21. Turntable

18. Tone Arm Lock

TAPE SIDE VIEW

23. Tape Eject/ Fast-Forward Button

24. Tape entrance