Toner Cable G2 User Manual
Telephone: Nationwide: Fax: E-mail: Internet:
07/02
Corning Gilbert G2 2-Piece Connector Series
215-675-2053 800-523-5947 215-675-7543 info@tonercable.com http://www.tonercable.com
969 Horsham Road
Horsham, Pennsylvania 19044 USA
G2 2-Piece Connector Series
Corning Gilbert Introduces the next
generation in 2-piece connectors with
patented design features providing
clear performance advantages over
traditional 2-piece connectors.
Only the G2 Series gives installers a
full view of the cable’s center conductor insertion into the connector seizing
mechanism, eliminating traditional blind
entry. A unique center conductor seizing system prevents actuator lockup
and preserves connector reusability.
With the patented support sleeve located in the back nut of the connector,
cable “pull back” is minimized. This
eliminates cable kinking typically associated with 2-piece connector installation.
An industry first tri-start threading system (patent pending) minimizes the
required back nut rotations when tightening the connector.
MATERIALS AND CONSTRUCTION
BODY COMPONENTS:
ASTM 6262 aluminum alloy with gold chromate conversion coating for excellent corrosion resistance and dry lubricant to prevent thread galling
RF COMPONENTS:
Contact pins and support sleeves are
brass with bright acid tin plating providing
excellent RF conductivity.
O-RINGS:
Ultraviolet and ozone resistant EPDM for
maximum durability.
SPECIFICATIONS
Connectors are designed to meet SCTE interface
specifications
BANDWIDTH: 5 MHz to 1 GHz
OPERATING RANGE: -40°F TO +140°F
NOMINAL IMPEDANCE: 75 ohms
SHIELDING EFFECTIVENESS: >130 dB
RETURN LOSS: 30 dB min to 1 GHz
INSERTION LOSS: <0.12 dB (pin types)
CABLE RETENTION: Meets or exceeds the cable
manufacturers’ maximum pulling tension specifications
Flush insulator prevents
moisture from collecting
or migrating along the pin
Actuator closing mechanism
preserves reusability
Tri-start threading system
reduces installation time
Support sleeve located
in back nut reduces "pull
back" during installation
Back nut radius allows
smooth transition of
heat shrink tubing
No "blind entry" of
center conductor into
seizing mechanism
Non-rotational design
for installation and
disassembly
Toner Cable Equipment, Inc. Specifications Subject To Change Without Notice.
Telephone: Nationwide: Fax: E-mail: Internet:
Corning Gilbert G2 2-Piece Connector Series
215-675-2053 800-523-5947 215-675-7543 info@tonercable.com http://www.tonercable.com
PART NUMBER HEX SIZE
COMMSCOPE P-III
TIMES FIBER T-10
.500 G2-500-TYPE-P3 1.000”
.625 G2-625-TYPE-P3 1.125”
.750 G2-750-TYPE-P3 1.250”
.875 G2-875-TYPE-P3 1.375”
COMMSCOPE QR
.540 G2-540-TYPE-QR 1.125”
.715 G2-715-TYPE-QR 1.250”
.860 G2-860-TYPE-QR 1.375”
TIMES FIBER TX-10
.565 G2-565-TYPE-TX 1.125”
.700 G2-700-TYPE-TX 1.250”
.840 G2-840-TYPE-TX 1.375”
TRILOGY MC2
.500 G2-500-TYPE-MC2 1.125”
.650 G2-650-TYPE-MC2 1.250”
.750 G2-750-TYPE-MC2 1.375”
ORDERING INFORMATION
TYPE
CH Pin Connector
SP Splice Connector
EXT3 3” Extension Connector
EXT6 6” Extension Connector
BAFF “F” Female Connector
AFM “F” Male Connector
Example:
G2-500-CH-P3 is a ‘Pin Connector’ for
.500 P3/T10 cable
2.31 [58.7 mm]
CENTER
CONDUCTOR
TRIM GAUGE
5/8-24 THREAD
.067 [1.7 mm]
.31 [7.9 mm]
Loading...