MODEL
MODEL
MODELMODEL
GS
GS----91EZ / GS
91EZ / GS----99992EZ
GSGS
91EZ / GS91EZ / GS
GS
GS----11
111EZ / GS
GSGS
1EZ / GS----11
1111
1EZ / GS1EZ / GS
2EZ
2EZ2EZ
112EZ
2EZ
1111
2EZ2EZ
CAUTION
CAUTION
CAUTIONCAUTION
Read and fully understand all the instructions before use.
Keep this manual in designated place for easy and quick reference.
The models mentioned on this manual are designed for use outside Japan.
Warranty shall be void if above mentioned models are use in Japan.
PREFACE
PREFACE
PREFACEPREFACE
Thank you for purchasing .
■ Upon receipt, check and confirm the following:
- Check any transport damages.
- Check for any loose or lost screws and bolts.
- Check the model as per order.
- Check all the accessories are contained.
If any problems are found, contact your distributor.
■ Read this instruction manual carefully before use.
Full understanding of manual is essential to prevent personal injury or
malfunction.
■ Keep this manual in a bag attached to the back of metal case lid for easy
and quick reference.
■ If manual or warning label is lost or becomes illegible, or if additional
manual is required, contact your distributor.
If you have any questions about the products or the contents of this
instruction manual, contact your distributor.
■ This manual is only applicable to outside Japan.
- 1 -
SAFETY INSTRUCTION
SAFETY INSTRUCTION
SAFETY INSTRUCTIONSAFETY INSTRUCTION
This manual specifies three (3) basic safety instructions:
■ Instructions are classified by degree of risk and described as follows:
Danger is used to indicate threatening
dangerous or unsafe practices which could
immediately result in severe personal injury
or death in the worst case.
Warning is used to indicate hazardous or
unsafe practices which could result in severe
personal injury or death in the worst
occasion.
Caution is used to indicate hazardous or
unsafe practices which could result in
Even if the risk is classified as , risk could become more serious result
depending on conditions. Make sure to follow all instructions when using.
personal injury or product or property
damage.
- 2 -
TABLE OF CONTENTS
TABLE OF CONTENTS
TABLE OF CONTENTSTABLE OF CONTENTS
1．GENERAL SAFETY INSTRUCTIONS ・・・・・・ 4
2．APPLICATION ・・・・・・・・・・・・・・・・・・・・・・・・ 7
3． PRECAUTIONS FOR USE ・・・・・・・・・・・・ 7
4．PART NAME ･･････・･･･････････････････ 13
5．FEATURES ･･･････････・・・・・・・・・・・･･･・ 14
6．BEFORE USE ・･･・・・・・・・・･・・･・・・・・・・・・ 14
7．OPERATING PROCEDURE ・・・・・・・・・・・ 15
8．CHANGING SOCKET ・・・・・・・・・・・・・・・・・・ 17
9．INSPECTION & MAINTENANCE ・・・・・・・・・ 19
10．SPECIFICATIONS ･・・・・・・・・・・・・・・・・・ 21
11．AFTERSALES SERVICE ・・・・･・・・・・・・ 22
- 3 -
1.
1. GENERAL SAFETY INSTRUCTIONS
GENERAL SAFETY INSTRUCTIONS
1.1.
GENERAL SAFETY INSTRUCTIONSGENERAL SAFETY INSTRUCTIONS
WARNING
WARNING
WARNINGWARNING
When using electric tools, basic safety precautions, including the following, should
always be followed to reduce the risk of fire, electric shock and personal injury.
Read all these instructions before operating this product and keep these
instructions.
SAVE
SAVE THESE
SAVESAVE
1)
1) Work area
Work area
1)1)
Work areaWork area
a) Keep work area clean and well lit. Cluttered and dark areas invite
accidents.
b) Do not operate power tools in explosive atmospheres, such as in
the presence of flammable liquids, gases or dust. Power tools create
sparks which may ignite the dust of fumes.
c) Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.
2)
2) Electrical safety
Electrical safety
2)2)
Electrical safetyElectrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any way.
Do not use any adapter plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering
a power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or
unplugging the power tool. Keep cord away from heat, oil, sharp
edges or moving parts. Damaged or entangled cords increase
the risk of electric shock.
THESE INSTRUCTIONS
THESETHESE
INSTRUCTIONS
INSTRUCTIONSINSTRUCTIONS
- 4 -
e) When operating a power tool outdoors, use an extension cord
suitable for outdoor use. Use of a cord suitable for outdoor use reduces
the risk of electric shock.
3)
3) Personal safety
Personal safety
3)3)
Personal safetyPersonal safety
a) Stay alert, watch what you are doing and use common sense
when operating a power tool. Do not use a power tool while you are tired
or under the influence of drugs, alcohol or medication.
A moment of inattention while operating power tools may result in serious
personal injury.
b) Use safety equipment. Always wear eye protection. Safety equipment
such as dust mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce personal injuries.
c) Avoid accidental starting. Ensure the switch is in the off position
before plugging in. Carrying power tools with your finger on the switch
or plugging in power tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on.
A wrench or a key left attached to a rotating part of the power tool may
result in personal injury.
e) Do not overreach. Keep proper footing and balance at all times.
This enables better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewelry. Keep your hair,
clothing and gloves away from moving parts. Loose clothes, jewelry or
long hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction and collection
facilities, ensure these are connected and properly used. Use of these
devices can reduce dust related hazards.
- 5 -
4)
4) Power tool use and care
Power tool use and care
4)4)
Power tool use and carePower tool use and care
a) Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer at the
rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off.
Any power tool that cannot be controlled with the switch is dangerous and
must be repaired.
c) Disconnect the plug from the power source before making any adjustments,
changing accessories, or storing power tools. Such preventive safety
measures reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow
persons unfamiliar with the power tool or these instructions to operate the
power tool. Power tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tools
operation. If damaged, have the power tool repaired before use.
Many accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc., in accordance with
these instructions and in the manner intended for the particular type of
power tool, taking into account the working conditions and the work to be
performed. Use of the power tool for operations different from intended
could result in a hazardous situation.
5)
5) Service
Service
5)5)
ServiceService
a) Have your power tool serviced by a qualified repair person using
only identical replacement parts. This will ensure that the safety of the
power tool is maintained.
.
- 6 -
2222.... APPLICATION
APPLICATION
APPLICATIONAPPLICATION
■ is an electric tool for tightening Tension Control
Bolt/Nut/Washer assemblies.
3333.... PRECAUTIONS FOR USE
■ To prevent accidents, personal injury and etc, read and follow all instructions
● Beware of electric shock when operating at high place.
This electric wrench has double insulation structure. An electric conductor
portion is insulated by two insulators which enhances safety against electric
shock. The electric wrenches that have double insulated structure are clearly
PRECAUTIONS FOR USE
PRECAUTIONS FOR USE PRECAUTIONS FOR USE
listed below.
DANGER
DANGER
DANGERDANGER
Beware of electric shock when operating at high place.
Beware of electric shock when operating at high place.Beware of electric shock when operating at high place.
○ Failure to follow this instruction may result in fall down accidents.
－ About Double Insulation
About Double Insulation －
About Double InsulationAbout Double Insulation
marked with
(Double Insulation Mark) on the rating plate.
- 7 -
WARNING
WARNING
WARNINGWARNING
● Beware of electric shock.
Beware of electric shock.
Beware of electric shock.Beware of electric shock.
○ Never use the wrench under rainy or snowy condition.
○ Never touch the plug with wet hands.
Failure to follow this instruction may result in electric shock, fire or
electric leakage.
● Electric cord must be regularly inspected.
Electric cord must be regularly inspected.
Electric cord must be regularly inspected. Electric cord must be regularly inspected.
○ Stop using the wrench if there is a problem with the electric cord.
○ Contact your distributor for repair.
Failure to follow this instruction may result in electric shock or electric
leakage.
● Never use the wrench around the place where gasoline, gas,
Never use the wrench around the place where gasoline, gas,
Never use the wrench around the place where gasoline, gas, Never use the wrench around the place where gasoline, gas,
thinner, benzene, etc., are stored.
thinner, benzene, etc., are stored.
thinner, benzene, etc., are stored.thinner, benzene, etc., are stored.
○ Do not use the wrench around flammable substances to avoid the
accidental fire caused by the spark out of the electric motor.
● Beware of fall down accident
Beware of fall down accidentssss when working at a high place.
Beware of fall down accidentBeware of fall down accident
○ Wear safety belt
○ Provide safety net or canvas as safe guarding against falling items.
○ Confirm that no one is underneath the working site before operation.
○ Stop operation when physically or mentally tired.
Failure to follow these instructions may result in fall down accidents.
● Avoid overloading.
Avoid overloading.
Avoid overloading.Avoid overloading.
○ Use the wrench and its accessories within the rated specifications.
Overloaded wrench and its accessories may result in malfunction of the
wrenches, accidents or personal injury.
when working at a high place.
when working at a high place. when working at a high place.
- 8 -
WARNING
WARNING
WARNINGWARNING
● Properly install bar sockets as described in this manual.
Properly install bar sockets as described in this manual.
Properly install bar sockets as described in this manual. Properly install bar sockets as described in this manual.
○ Incomplete installation may result in accidents and personal injury.
See “CHANGING SOCKETS” on page 17.
● Avoid accidental Starti
Avoid accidental Starting.
Avoid accidental StartiAvoid accidental Starti
○
Ensure that the switch is in the off-position before plugging into power
source.
○ Never carrying the wrench with your fingers on the switch when the plug
is connected to power source.
● Disconnect the plug from the power source when:
Disconnect the plug from the power source when:
Disconnect the plug from the power source when: Disconnect the plug from the power source when:
○ Not in use.
○ Changing accessories.
○ Inspection and maintenance.
○ Or other danger is foreseen.
Failure to follow these instructions may result in accidental starting and
personal injury.
ng.
ng.ng.
● Do not disassemble or modify the wrench.
Do not disassemble or modify the wrench.
Do not disassemble or modify the wrench. Do not disassemble or modify the wrench.
○ Disassembly or modification made by unauthorized personnel may result
in malfunction or personal injury.
○ Disassembly & Re-assembly work is permitted for the following
expendables: Inner Socket, Outer Socket, Set Screws, Inner Socket
Spring, Ejector Pin, Ejector Spring and Carbon Brushes.
● Store wrench in the metal case and keep it at the designated
Store wrench in the metal case and keep it at the designated
Store wrench in the metal case and keep it at the designated Store wrench in the metal case and keep it at the designated
place when not in use.
place when not in use.
place when not in use. place when not in use.
○ Store wrench in lockable dry location to keep any unauthorized
personnel away.
Failure to follow this instruction may result in malfunction or accidents.
- 9 -
WARNING
WARNING
WARNINGWARNING
● Immediately stop using the wrench and disconnect the plug when
Immediately stop using the wrench and disconnect the plug when
Immediately stop using the wrench and disconnect the plug when Immediately stop using the wrench and disconnect the plug when
unusual
unusual sound, vibration or smell is detected.
unusualunusual
○ Contact your distributor immediately.
Failure to follow this instruction may result in serious injury.
● Contact your distributor f
Contact your distributor for repair service.
Contact your distributor fContact your distributor f
○ Repair work should only be carried out by a qualified serviceman.
○ Repair work done by an inexperienced person may cause accidents,
● Check the following items before operation.
Check the following items before operation.
Check the following items before operation.Check the following items before operation.
○ Check for any deformation, crack or damage on the wrench body,
○ Do not use the wrench if any problem are found on items listed above.
○ Make sure that socket assembly is correctly installed on the wrench.
○ Make sure that set screws are securely fastened. Loose installation
sound, vibration or smell is detected.
sound, vibration or smell is detected. sound, vibration or smell is detected.
or repair service.
or repair service. or repair service.
injury or malfunction.
sockets, electric cord, plug and etc.
may result in accidents and personal injury.
● Use appropriate power source as indicated on the rating plate.
Use appropriate power source as indicated on the rating plate.
Use appropriate power source as indicated on the rating plate.Use appropriate power source as indicated on the rating plate.
Failure to follow this instruction may result in fire or burn accidents.
● Immediately check the wrench when it
Immediately check the wrench when it is dropped down or
Immediately check the wrench when it Immediately check the wrench when it
banged.
banged.
banged.banged.
○ Check for deformation, crack, damage and other abnormality. Stop
using the wrench if any abnormality is found.
Continued use of fault wrench may result in accidents and personal injury.
- 10 -
is dropped down or
is dropped down or is dropped down or
CAUTION
CAUTION
CAUTIONCAUTION
● Keep work area clean.
Keep work area clean.
Keep work area clean.Keep work area clean.
○ Cluttered areas and benches invite accidents.
● Keep children away.
Keep children away.
Keep children away.Keep children away.
○ Do not let children touch the wrench and electric cord.
○ All visitors should be kept away from work area.
● Secure work area.
Secure work area.
Secure work area.Secure work area.
○ Keep body stance balanced and firmed.
○ Never wrap the electric cord around something.
○ Keep work area well lit.
● Use
Use suitable model for each application.
suitable model for each application.
UseUse
suitable model for each application. suitable model for each application.
○ Do not use wrench beyond its rated specifications.
○ Do not use wrench for purpose not intended.
● Dress properly.
Dress properly.
Dress properly.Dress properly.
○ Always wear gloves and non-skid footwear when operating outdoor.
○ Always wear safety helmet.
● Use genuine accessories or attachments manufactured by
Use genuine accessories or attachments manufactured by
Use genuine accessories or attachments manufactured by Use genuine accessories or attachments manufactured by
Maeda Metal Industries, Ltd.
Maeda Metal Industries, Ltd.
Maeda Metal Industries, Ltd.Maeda Metal Industries, Ltd.
● Do not connect multiple plugs to a single outlet by using multiple
Do not connect multiple plugs to a single outlet by using multiple
Do not connect multiple plugs to a single outlet by using multiple Do not connect multiple plugs to a single outlet by using multiple
outlet adaptors.
outlet adaptors.
outlet adaptors.outlet adaptors.
○ Over current may cause fire, accidents or malfunction.
● Do not abuse the electric cord.
Do not abuse the electric cord.
Do not abuse the electric cord.Do not abuse the electric cord.
○ Never use the electric cord for carrying, pulling, or unplugging the
power.
○ Keep the electric cord away from heat, oil, sharp edges or moving
parts.
- 11 -
CAUTION
CAUTION
CAUTIONCAUTION
● Keep electric motor well ventilated.
Keep electric motor well ventilated.
Keep electric motor well ventilated.Keep electric motor well ventilated.
○ Do not put any foreign materials into the vent.
○ Do not block exhaust vent.
● Maintain wrench.
Maintain wrench.
Maintain wrench.Maintain wrench.
○ Keep wrench handle clean, dry and free of oil or grease.
● Provide leakage breaker as a shock guard for each wrench.
Provide leakage breaker as a shock guard for each wrench.
Provide leakage breaker as a shock guard for each wrench.Provide leakage breaker as a shock guard for each wrench.
○ Although double insulated wrench does not require leakage breaker,
use of leakage breaker is strongly recommended as an extra
safeguard.
● When applying extension cord, select shorter extension units
When applying extension cord, select shorter extension units
When applying extension cord, select shorter extension units When applying extension cord, select shorter extension units
than specified below depending on the cross section.
than specified below depending on the cross section.
than specified below depending on the cross section.than specified below depending on the cross section.
Max. Length Nominal conducting
cable cross section
H07RN-F
AWG 14
AWG 12
AWG 10
1.25mm2 10m 20m
2.0mm2 20m 40m
3.5mm2 30m 60m
110-120V 220-230V
50ft
80ft
130ft
100ft
160ft
260ft
○ Using extension cord more than Maximum Length may result in
malfunction or breakdown due to performance drop of the wrench.
● Use attached connector when using extension cord.
Use attached connector when using extension cord.
Use attached connector when using extension cord.Use attached connector when using extension cord.
● Observe local laws and rules concerning noise level.
Observe local laws and rules concerning noise level.
Observe local laws and rules concerning noise level.Observe local laws and rules concerning noise level.
- 12 -
4444.... PART NAME
PART NAME
PART NAME PART NAME
(Figure 1)
MODEL ACCESSORIES
Inner Socket
GS-91EZ
GS-92EZ
GS-111EZ
GS-112EZ
●●●● Contact your distributor for other available sockets and accessories.
Contact your distributor for other available sockets and accessories.
Contact your distributor for other available sockets and accessories.Contact your distributor for other available sockets and accessories.
Outer Socket
Inner Socket Spring
Ejector Pin
Ejector Spring
Screwdriver (-)
Instruction Manual
- 13 -
5555.... FEATURES
FEATURES
FEATURESFEATURES
・ All New Design Aluminum Double Insulated Motor.
・ Anti-defacement Mechanism Inner Socket.
6666.... BEFOR
BEFORE USE
BEFORBEFOR
● Check followings before
Check followings before connecting
Check followings before Check followings before
○
1. Check for any deformation, crack or damage on wrench body, socket, electric
cord, etc.
Do not use wrench if any problem is found on items listed above.
E USE
E USEE USE
WARNING
WARNING
WARNINGWARNING
connecting the plug into power source.
connectingconnecting
Accidental starting invites personal injury.
the plug into power source.
the plug into power source. the plug into power source.
2. Make sure to use commercial power supply.
Use appropriate power source as indicated on the rating plate.
3. Make sure that socket assembly is correctly installed on the wrench.
4. Make sure that set screws are securely fastened.
Loose installation may result in accidents and personal injury.
See “CHANGING SOCKETS” on page 17.
- 14 -
7777.... OPERATING PROCEDURE
OPERATING PROCEDURE
OPERATING PROCEDUREOPERATING PROCEDURE
CAUTION
CAUTION
CAUTIONCAUTION
● Snug tight using snug t
Snug tight using snug tightening wrench like
Snug tight using snug tSnug tight using snug t
required before using SHEAR WRENCH.
required before using SHEAR WRENCH.
required before using SHEAR WRENCH.required before using SHEAR WRENCH.
(1) Slide Inner Socket over the bolt pintail (Figure 2).
(2) Slide Outer Socket over the nut (Figure 3).
- Slightly turn Internal Gear when slide over is difficult.
- Outer Socket can not be engaged on the nut when Anti defacement mechanism
of the Inner Socket detects improper Inner Socket engagement. In such case,
back to step (1) and slide the Inner Socket over the bolt pintail completely.
ightening wrench like SNUG MASTER is
ightening wrench like ightening wrench like
SNUG MASTER is
SNUG MASTER is SNUG MASTER is
(Figure 2)
(Figure 3)
- 15 -
(3) Squeeze trigger switch to start tightening (Figure 4).
(Figure 4)
(4) Rotating speed gradually shows down as the tightening proceeds, then bolt
pintail shears off when designated torque is reached (Figure 5).
(Figure 5)
(5) When tightening is completed, remove wrench from bolt/nut assembly.
Sheared-off bolt pintail remains in Inner Socket (Figure 6).
(Figure 6)
(6) Pull Ejector Lever to eject bolt pintail (Figure 7).
Keep pintail in designated bag.
- 16 -
(Figure 7)
WARNING
WARNING
WARNINGWARNING
● Keep others a safe distance from work area.
Keep others a safe distance from work area.
Keep others a safe distance from work area.Keep others a safe distance from work area.
○ Do not throw pintail away. Collect pintail in designate bag during
operation.
Failure to follow this instruction may result in accidents and personal
injury.
8888.... CHANGING SOCKETS
CHANGING SOCKETS
CHANGING SOCKETSCHANGING SOCKETS
WARNING
WARNING
WARNINGWARNING
● Release ejector pin by pulling ejector lever before changing
Release ejector pin by pulling ejector lever before changing
Release ejector pin by pulling ejector lever before changing Release ejector pin by pulling ejector lever before changing
sockets.
sockets.
sockets.sockets.
Accidental ejector pin release invites blindness or injury.
(1) Remove inner & outer socket assembly from wrench by unscrewing set
screws (Figure 8). Do not remove set screws completely from outer socket
holder.
(Figure 8)
- 17 -
(2) Prepare outer and inner-sockets of the right sizes suitable for the size of bolt
to be tightened.
･･･Example : Use our standard socket for 3/4" to 3/4" bolts.
(3) As per (Figure 9), firstly install inner socket onto ejector-pin on the main body
and then, install outer-socket into inner-socket.
(Figure 9)
(4) There might be the case that perfect installation is not obtainable due to a gap
between main body and outer-socket, as shown per (Figure 10).
(Figure 10)
WARNING
WARNING
WARNINGWARNING
● There should be no gap between the socket assembly and the
There should be no gap between the socket assembly and the
There should be no gap between the socket assembly and the There should be no gap between the socket assembly and the
wrench
wrench....
wrenchwrench
The gap invites accidents or breakage of the sockets or the wrench body.
- 18 -
9999.... INSPECTION & MAINTENANCE
INSPECTION & MAINTENANCE
INSPECTION & MAINTENANCEINSPECTION & MAINTENANCE
WARNING
WARNING
WARNINGWARNING
● Disconnect plug from power source before inspection and
Disconnect plug from power source before inspection and
Disconnect plug from power source before inspection and Disconnect plug from power source before inspection and
maintenance.
maintenance.
maintenance.maintenance.
○ Accidental starting invites serious injury.
● Replace the inner socket when sheared bolt pintail is came off
Replace the inner socket when sheared bolt pintail is came off
Replace the inner socket when sheared bolt pintail is came off Replace the inner socket when sheared bolt pintail is came off
tttthe inner socket without pulling the ejector lever.
he inner socket without pulling the ejector lever.
he inner socket without pulling the ejector lever.he inner socket without pulling the ejector lever.
○ There is a risk of unexpected bolt pintail ejection when inner drive of
the inner socket is worn down. The inner socket must be immediately
replaced.
Failure to follow this instruction may result in serious accidents and injury.
(1) Clean dust and debris from the sockets periodically.
(2) Use only a damp cloth to clean your wrench and sockets since certain
cleaning agents and solvents are harmful to those parts. Some of these
include: benzene, thinner, gasoline and etc.
(3) Never put solvents into the exhaust vent.
(4) Store wrench in the metal case after operation and keep it dry.
(5) Ejector pin must be regularly inspected and replaced when it wears down.
Sheared bolt pintail will not be ejected from inner socket with worn ejector
pin.
- 19 -
(6) Carbon brush must be regularly inspected and replaced with the new genuine
carbon brush when brush length becomes less than 5mm (Figure 11).
*Carbon brushes are placed in two positions.
*Indicate the wrench model when carbon brushes are needed because carbon brush differs
from model to model.
(Figure 11)
(7) Replace carbon brush as shown in the following figure 12.
(Figure 12)
(8) Overhaul must be carried out every 6 months or 30,000 tightening, whichever
comes first. Contact your distributor for overhaul.
- 20 -
10
10.... SPECIFICATIONS
SPECIFICATIONS
1010
SPECIFICATIONSSPECIFICATIONS
Model GS-91EZ GS-92EZ GS-111EZ GS-112EZ
Frequency 50-60 Hz
Voltage
(Single Phase)
Max Current 17A 8.5A 19A 9.5A
Rated Power 1750W 2000W
Intermittent
Operation
Rated
Max Torque
Rated
No-load Speed
Noise
&
Vibration Level
Adaptable
Bolt
Dia.
Insulation Class
A325
A490
Weight 7.6kg 8.1kg
110-120 V 220-230 V 110-120 V 220-230 V
2s / 3s
810 lbf.ft
(1100 N･m)
-1
17min
1”, 7/8”, 3/4”, 5/8” 1-1/8”, 1”, 7/8”, 3/4”
1”, 7/8”, 3/4”, 5/8” 1-1/8”, 1”, 7/8”, 3/4”
(rpm) 15min
Sound Pressure Level 84 dB(A)
Sound Power Level 95 dB(A)
Vibration Level 2.5 m/s2 or below
Class II (Double Insulation)
1030 lbf.ft
(1400 N・m)
-1
(rpm)
● Weight excludes socket & cord.
- 21 -
11111111.... AFTER SALES SERVICE
AFTER SALES SERVICE
AFTER SALES SERVICEAFTER SALES SERVICE
■ Contact your distributor for available services.
■ Provide model, serial number, date of purchase and details of failure
when contacting your distributor.
CAUTION
CAUTION
CAUTIONCAUTION
● Do not use wrench when malfunction, deficiency in wrenches
Do not use wrench when malfunction, deficiency in wrenches’’’’
Do not use wrench when malfunction, deficiency in wrenchesDo not use wrench when malfunction, deficiency in wrenches
pppperformance, personal injury or property loss is foreseen.
erformance, personal injury or property loss is foreseen.
erformance, personal injury or property loss is foreseen.erformance, personal injury or property loss is foreseen.
If possible, prepare backup wrenches beforehand.
- 22 -
IMKA051
Loading...