Tommy Bahama TB344AP00, TB344DBZ00 Owner's Manual
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
Part No. F40BP72890001 Form No. BP7289-1
READ AND SAVE THESE INSTRUCTIONS
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
BAHAMA BREEZES
Damp Location
Ceiling Fan Owner's Manual
Net Weight:
19.0 Lbs.
TB344AP00
Antique Pewter
Housing
TB344DBZ00
Distressed Bronze
Housing
Model Numbers
2
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO
PERSONS, OBSERVE THE FOLLOWING:
a. Use this unit only in a manner intended by the manufacturer. If you have questions,
contact the manufacturer.
b. Before servicing or cleaning unit, switch power off at service panel and lock service
panel disconnecting means to prevent power from being switched on accidentally.
When the service disconnecting means cannot be locked, securely fasten a warning
device, such as a tag, to the service panel.
1. Read your owner’s manual carefully and keep it for future reference.
2. Be careful of the fan and blades when cleaning, painting, or working near the fan.
Always turn off the power to the ceiling fan before servicing.
3. Do not put anything into the fan blades while they are turning.
4. Do not operate reversing switch until fan blades have come to a complete stop.
Additional Safety Instructions for Installation
1. To avoid possible shock, be sure electricity is turned off at the fuse box before wiring,
and do not operate fan without blades.
2. The installation is to be in accordance with the National Electrical Code, ANSI/NFPA
70-2011 and Local Codes. Use the National Electrical Code if Local Codes do not exist.
The ceiling fan must be grounded as a precaution against possible electrical shock.
Electrical installation should be made or approved by a licensed electrician.
3. The outlet box and joist must be securely mounted and capable of reliably supporting
at least 50 pounds. Use only U.L. outlet boxes listed as “Acceptable for Fan Support of
22.7 kg. (50 lbs.) or less”, and use the mounting screws provided with the outlet box.
Most outlet boxes commonly used for support of light fixtures are not acceptable for
fan support and may need to be replaced. Consult a qualified electrician if in doubt.
4. The fan must be mounted with the fan blades at least 7 feet from the floor to prevent
accidental contact with the fan blades.
5. Follow the recommended instructions for the proper method of wiring your ceiling
fan. If you do not know enough about electrical wiring, have your fan installed by a
licensed electrician.
NOTE: This fan is suitable for use with solid-state speed controls.
WARNING: To avoid fire, shock or injury, do not use a Tommy Bahama or any other
brand of control not specifically approved for this fan.
WARNING: This product is designed to use only those parts supplied with this product
and/or any accessories designated specifically for use with this product by Emerson
Electric Co. Substitution of parts or accessories not designated for use with this product
by Emerson Electric Co. could result in personal injury or property damage.
WARNING: To reduce the risk of personal injury, do not bend the blade flange when
installing the blade flanges, balancing the blades or cleaning the fan. Do not insert foreign
objects in between rotating fan blades.
NOTE: All setscrews must be checked and re-tightened where necessary before
installation.
!
WARNING
DATE CODE:
The date code of this fan may be found on the box, stamped in ink on a white label.
You should record this data above and keep it in a safe place for future use.
3
THIS FAN IS SUITABLE FOR DAMP LOCATIONS SUCH AS
COVERED PORCHES, COVERED PATIOS, AND COVERED DECKS...
ANYWHERE THERE IS A ROOF OVERHEAD.
Tools Needed for Assembly
One Phillips head screwdriver
One wire stripper
One stepladder
One 5/32” hex wrench (supplied)
Four wire connectors (supplied)
Materials
Wiring, outlet box and box connectors must be
of type required by the local code. The minimum wire would be a 3-conductor (2-wire with
ground) of the following sizes:
This Manual Is Designed to Make it as Easy as Possible for You to
Assemble, Install, Operate and Maintain Your Ceiling Fan
Installed Wire Length Wire Size A.W.G.
Up to 50 ft. 14
50-100 ft. 12
Before assembling your ceiling fan, refer to
section on proper method of wiring your
fan (page 9). If you feel you do not have
enough wiring knowledge or experience,
have your fan installed by a licensed electrician.
!
WARNING
Unpacking Instructions
For your convenience, check-off boxes are provided next to each step. As each step
is completed, place a check mark in the box. This will insure that all steps have been
completed and will be helpful in finding your place should you be interrupted.
Do not install or use fan if any part is damaged or missing. Call Toll-Free:
1-800-654-3545
!
WARNING
This product is designed to use only those
parts supplied with this product and/or
any accessories designated specifically for
use with this product by Emerson Electric
Co. Substitution of parts or accessories
not designated for use with this product by
Emerson Electric Co. could result in personal injury or property damage.
!
WARNING
1. Open styrofoam unit containing fan.
Remove top half of styrofoam unit.
Remove parts and check to see that you
have received the following parts:
NOTE: If you are uncertain of part
description, refer to exploded view
illustration.
a. Fan motor and housing assembly
b. One ceiling cover
c. One motor cover
d. Five blade flanges
e. One hanger bracket
f. One hanger ball/downrod assembly
g. One switch housing cover
Your new ceiling fan will require a grounded
electrical supply line of 120 volts AC, 60 Hz,
15 amp circuit.
The outlet box must be securely anchored and
capable of withstanding a load of at least 50
pounds.
4
To reduce the risk of fire, electric shock, or
personal injury, mount fan to outlet box
marked “Acceptable for Fan Support of
22.7 kg. (50 lbs.) or less”, and use screws
supplied with outlet box. Most outlet boxes
commonly used for support of light fixtures are not acceptable for fan support
and may need to be replaced. Consult a
qualified electrician if in doubt.
!
WARNING
h. One loose parts bag containing:
1. One 5/16-18 x 1/4” setscrew
2. One 5/32” hex wrench
3. Two 1” threaded studs
4. Two 1-1/4” threaded studs
5. Four knurled knobs
6. Four lockwashers
7. Four wire connectors
8. One hibiscus pendant
9. One bell pendant
10. Two couplings
11. One clevis pin/hairpin clip
assembly
Electrical Requirements
12. Eleven 10-32 x 3/4” oval head
screws
13. Twenty-one 10-32 x 5/16”
Phillips pan head screws
14. Twenty-one #10 flat washers
15. Two 8-32 x 3/8” pan head
screws
NOTE: Place the parts from the loose
parts bags in a small container to keep
them from being lost. If any parts are
missing, contact your local retailer or
catalog outlet for replacement before
proceeding.
If your fan is to replace an existing ceiling light
fixture, turn electricity off at the main fuse or
circuit breaker box at this time and remove the
existing light fixture.
Turning off wall switch is not sufficient. To
avoid possible electrical shock, be sure
electricity is turned off at the main fuse or
circuit breaker box before wiring. All
wiring must be in accordance with
National and Local codes and the ceiling
fan must be properly grounded as a precaution against possible electrical shock.
!
WARNING
C
A
B
E
D
H
G
F
DOWNROD
CLEVIS
PIN
5/16-18" x 1/4"
SETSCREW
MOTOR
COUPLING
HAIRPIN
CLIP
5
IMPORTANT: If you are going to use a
Tommy Bahama remote control and
receiver to control your fan, perform the
instructions in this Owner’s Manual in
conjunction with the instructions contained in the remote control/receiver
Owner’s Manual.
1. Remove the fan motor and housing assem-
bly from the styrofoam packaging and position it so that the top of the motor is facing
you.
2. Remove the hanger ball from the downrod
by loosening the setscrew in the hanger ball
until the ball falls freely down the downrod
(Figure 1). Remove the pin from the downrod, then remove the hanger ball. Retain
the pin and hanger ball for reinstallation in
step 8.
3. Separate, untwist and unkink the three
motor leads. Route the motor leads through
the downrod and seat the downrod in the
motor coupling (Figure 2).
Figure 1
Figure 2
The Tommy Bahama TB344 Series Ceiling
Fan is designed to be operated from wall
switch(es), or from a Tommy Bahama remote
control/ transmitter. There are no controls
supplied with the ceiling fan.
How to Assemble Your Ceiling Fan
4. Align the clevis pin holes in the downrod
with the holes in the motor coupling. Install
the clevis pin and secure with the hairpin
clip (Figure 2). (Pin and clip are supplied in
loose parts bag.) The clevis pin must go
through the holes in the motor coupling
and the holes in the downrod. Push the
straight leg of the hairpin clip through the
hole near the end of the clevis pin until the
curved portion of the hairpin clip snaps
around the clevis pin. The hairpin clip must
be properly installed to prevent the clevis
pin from working loose. Pull on the downrod to make sure the clevis pin is properly
installed.
To avoid possible fire or shock, follow all
wiring instructions carefully.
Any electrical work not described in these
instructions should be done or approved
by a licensed electrician.
!
WARNING
IMPORTANT: Your ceiling fan and
optional Tommy Bahama remote control will not function properly, and may
be damaged, it used with any wall dimmer switch or control other than Tommy
Bahama Wall Control, Model No.
TBSW02. Use only this Tommy Bahama
Wall Control or a listed general use
on/off wall switch.
PIN
HANGER
BALL
DOWNROD
SETSCREW
Loading...