Page 1
Dear Customer,
0
m
+
3
m
+
6
m
+
slow flow med flow fast flow
1 2 3
Congratulations on choosing the Tommee Tippee Ultra bottle. To help you
get the most out of this bottle we recommend that you read these instructions
carefully.
Every moment you share with your baby is special. And when it’s time for their
™
bottle, you want it to be a relaxed experience for both of you. Our new Ultra
bottles feature our unique ‘contoured and angled’ teat, helping your baby latch
on, stay on and feed comfortably.
bottle and teat instructions
Here’s to the perfect feeding experience!
Product Assembly
Insert the teat into the
1
Hygiene
cover
Teat
Valve
Screw
ring
Bottle
base
REMEMBER: You don’t have to disassemble the teat
and screw ring for sterilising.
Quick Start
1
Before use, wash all parts in warm soapy water,
rinse in clean water and sterilise.
Assemble your bottle as per the diagram.
2
3
When assembling your bottle
it is important that you check
the valve by holding it to the
light to check that the slit in
the silicone has not sealed
closed. If it has sealed closed,
pinch it gently with teat tongs
to re-open. If the valve has sealed closed your
bottle will not vent properly.
Make up your feed.
4
Serve.
5
After use, wash all parts in warm soapy water,
6
rinse in clean water, ready to sterilise once more.
screw ring, aligning the
two locators.
u
Pull the teat through
2
&
t
n
a
d
e
e
t
r
s
f
i
o
d
e
to ensure it
fully ‘clips’
into the
screw
ring.
s
Storage and Use
Inspect before each use and pull the feeding teat in all
3
directions. Throw away at the first signs of
damage or weakness.
Keep all components not in use out of reach of children.
3
For safety and hygiene reasons it is recommended that
3
the feeding teat is replaced every 2 months.
When making up a feed, follow the formula milk
3
manufacturer’s instructions.
Do not store or leave in direct sunlight or near a source
7
of heat or leave in disinfectant (“Sterilising Solution”)
g
n
i
r
w
e
r
c
for longer than recommended, as this may weaken
the teat.
Do not store with or allow to come into contact with
7
solvents or harsh chemicals.
Not suitable for use in a conventional oven or a
7
combination microwave oven with the grill feature
switched on.
Do not heat in a microwave with bottle sealed. Remove
7
teat, locking ring and dome cap.
Warnings
FOR YOUR CHILDS SAFETY & HEALTH
WARNING!
Always use this product with adult supervision. Accidents
3
have occurred when babies have been left alone with
drinking equipment due to the baby falling or if the
product has been disassembled.
Always check food temperatures before feeding. Heating
3
in a microwave oven may produce localised high
temperatures. Take extra care when microwave heating.
Always stir heated food to ensure even heat distribution
3
and test the temperature before serving.
Never use feeding teats as a soother.
7
Continuous and prolonged sucking of fluids will cause
7
tooth decay. Tooth decay in young children can occur
even when non-sweetened fluids are used. This can occur
if the baby is allowed to use the bottle for long periods
through the day and particularly through the night, when
saliva flow is reduced or if it is used as a soother.
Please remember..
it is important to increasethe flow rate of yourteat as your
baby grows.
Ultra teats are available in the following flow rates:
Cleaning and Sterilising
Before first use, clean the product.
3
Clean before each use.
3
Always wash the product immediately after use.
3
Before first use place in boiling water for 5 minutes.
3
This is to ensure hygiene.
Wash in warm soapy water and rinse in clean water or
3
use a dish washer (top shelf only).
For cleaning other bottle parts, use a closer to nature
3
teat & spout brush.
Once you have cleaned your bottles they are ready
3
to sterilise.
All bottle components should be sterilised.
3
All bottle components are suitable for sterilisation by
3
steam (electric or microwave), boiling or cold water
tablet / liquid solution.
TAKE EXTRA CARE when cleaning the valve.
3
In order to ensure optimum venting the teat valve is
manufactured using a thinner silicone than the teat itself
and therefore care needs to be taken during cleaning to
ensure no damage is caused.
Do not allow product to come into contact with oil based
7
foods (e.g. oil / tomato based sauces) as staining will occur.
Do not clean with solvents or harsh chemicals.
7
Do not turn the teat inside out for cleaning.
7
Damage could result.
DO NOT USE A TEAT BRUSH or any other implement to
7
clean the valve / the feeding hole as damage such as
splits and tears may occur. However, performance of the
teat may be affected if the valve is not cleaned
thoroughly after each use. Ensure valve is flushed with
warm water during cleaning.
Any questions?
Visit our website www.tommeetippee.com
call us FREE on 0500 97 98 99 (UK only)
tommeetippee.com
042210
Loading...