Hygiene cover alignment indicator
transition sippee trainer cup
INSTRUCTIONS FOR USE
Hygiene cover
Medium flow
Closer to Nature teat
REMEMBER to align the on the hygiene cover
with the on the screw ring.
Valve alignment indicator
Place the soft transition spout into the screw ring.
REMEMBER to align the valve with the arrow.
FOR YOUR CHILD’S SAFETY AND HEALTH
WARNING!
• Always use this product with adult supervision.
• Accidents have occurred when babies have been left alone with
drinking equipment due to the baby falling or if the product has
disassembled.
• Never use feeding teats or spouts as a soother.
• Continuous and prolonged sucking of fluids will cause tooth decay.
• Tooth decay in young children can occur even when non-sweetened
fluids are used. This can occur if the baby is allowed to use the cup
for long periods through the day and particularly through the night,
when saliva flow is reduced or if it is used as a soother.
• Always check food temperature before feeding.
• Heating in a microwave oven may produce localised high
temperatures. Take extra care when microwave heating.
• Always stir heated food to ensure even heat distribution and test the
temperature before serving.
• Keep all components not in use out of reach of children.
CLEANING AND STERILISING
• Before first use, clean the product.
• Clean before each use.
• Always wash the product immediately after use.
• Wash in warm soapy water and rinse in clean water or use a
dishwasher (top shelf only).
• Do not clean with solvents or harsh chemicals.
• Do not allow product to come into contact with oil based foods (e.g.
oil/tomato based sauces) as staining will occur.
• Do not turn the teat inside out for cleaning. Damage could result.
Use a teat brush
TAKE EXTRA CARE when cleaning the valve. In
order to ensure optimum venting the spout valve is
manufactured using a thinner silicone than the
spout itself and therefore care needs to be taken
during cleaning to ensure no damage is caused.
DO NOT USE A TEAT BRUSH or any other
implement to clean the valve/the feeding holes as
damage such as splits and tears may occur.
However, performance of the spout may be
affected if the valve is not cleaned thoroughly after
each use. Ensure valve is flushed with warm water
during cleaning.
Soft transition spout
tommeetippee.com
Screw ring
Cup handles
Cup base
• Before first use place in boiling water for 5 minutes. This is to ensure
hygiene.
• Once you have cleaned your cup it is ready to sterilise.
• All components can be sterilised but you may choose not to sterilise
the handles.
• All bottle components are suitable for sterilisation by steam (electric
or microwave), boiling or cold water tablet / liquid solution.
STORAGE AND USE
• Inspect before each use and pull the feeding teat/spout in all directions.
• Throw away at the first signs of damage or weakness.
• Do not store or leave in direct sunlight or near a source of heat.
• Do not store or leave a feeding teat or spout in direct sunlight or
near a source of heat or leave in disinfectant (“Sterilising Solution”)
for longer than recommended, as this may weaken the teat or spout.
• Do not store with or allow to come into contact with solvents or
harsh chemicals.
• Not suitable for use in a conventional oven or a combination
microwave oven with the grill feature switched on.
• For safety and hygiene reasons it is recommended that the feeding
teat is replaced every 2 months.
• Do not heat in a microwave with bottle/cup sealed - Remove spout
or teat, locking ring and dome cap.
• Not suitable for hot or fizzy (carbonated) drinks.
• As with most sippy cups, ours are to be used with milk, water or
juices that don’t contain pulp.
Jackel International Limited trading as Mayborn Group
Northumberland Business Park West
Cramlington
Northumberland
NE23 7RH, UK
Copyright © Jackel International Limited 2016.
TOMMEE TIPPEE is a registered trademark of Jackel International
Limited.
Jackel International Limited retains all intellectual property rights to this
product, packaging and printed or electronic media including all two
and three dimensional designs, graphic images, logos and text.
Jackel International Limited is incorporated in England and Wales
under company number 01894022.
Any manufacture, publication, copying, hiring, lending and reproduction
of any materials is strictly prohibited and constitutes infringement.
International patent applications pending.
Materials Listing: Polyproylene, Thermoplastic Elastomer & Silicone.
Made in China
0447080
Loading...