HOOD
TEAT AND
ADAPTER
express
and
G
o
SCREW RING
Pouch Bottle and Pouch
INSTRUCTIONS FOR USE
POUCH
HOLDER
ALL POUCHES COME
PRE-STERILISED
For your child’s safety and health
WARNING!
Always use this product with adult supervision. Accidents have occurred when babies have been left alone with drinking equipment due to the baby falling or if
the product has disassembled.
Never use feeding teats as a soother
Continuous and prolonged sucking of fluids will cause tooth decay. Tooth decay in young children can occur even when non-sweetened fluids are used.
This can occur if the baby is allowed to use the bottle for long periods through the day and particularly through the night, when saliva flow is reduced or if it is
used as a soother.
Always check food temperature before feeding.
Remember, never heat milk in a microwave and never boil breast milk as this will destroy valuable nutrients inthe milk. These methods can create localised hot
spots.
SCREW CAP
STORAGE
POUCH
CLEANING AND STERILISATION
(For all components except pouches)
Before first use place all components with the exception of the storage bags in boiling water for 5 minutes. This is to ensure hygiene.
Before first use, clean the product.
Clean before each use.
Always wash the product immediately after use.
Wash in warm soapy water and rinse in clean water or use a dishwasher (Top shelf only). Do not clean with solvents or harsh chemicals.
Do not allow product to come into contact with oil based foods (e.g. oil/tomato based sauces) as staining will occur.
Do not turn the teat inside out for cleaning.
Damage could result. Use a teat brush.
Suitable for sterilisation by steam (electric and microwave), boiling or cold water tablet/liquid solution.
STORAGE AND USE
Inspect before each use and pull the feeding teat in all directions. Throw away at the first signs of damage or weakness.
Do not store with or allow to come into contact with solvents or harsh chemicals.
Keep all components not in use out of reach of children.
Not suitable for microwave or conventional oven.
Do not leave a feeding teat in direct sunlight or heat, or leave in disinfectant (“sterilising solution”) for longer than recommended, as this may
weaken the teat.
For safety and hygiene reasons it is recommended that the feeding teat is replaced at least every 2 months.
Not suitable for hot or fizzy (carbonated) drinks.
Milk storage pouches are for single use only.
Jackel International Limited trading as Mayborn Group
Northumberland Business Park West
Cramlington
Northumberland
NE23 7RH, UK
Copyright © Jackel International Limited 2015
Jackel International Limited retains all intellectual property rights to this product and packaging, including all two and three dimensional designs, graphic images, logos and text.
Any unauthorised manufacture, publication, reproduction, communication or adaptation of any materials comprised in this product or its packaging is strictly prohibited and may constitute infringement
of relevant laws.
Jackel international limited is incorporated in England and Wales under company number 01894022.
TOMMEE TIPPEE and CLOSER TO NATURE are registered
trademarks of Jackel International Limited.
tommeetippee.com
0422470
1. CONNECTING STORAGE
POUCHES TO BREAST PUMP
Breast milk can be expressed directly in to express and go
breast milk pouches using our breast pump adapters
1
Select the relevant adapter for
the brand of breast pump you are
using
4 a
Once you have finished expressing or when the pouch is full, unscrew from
the pump and replace the screw cap
DISASSEMBLE THE REST OF THE UNIT AND STERILISE
ALL PARTS AS PER MANUFACTURERS GUIDELINES
2
Screw the adapter on to your
breast pump
4 b
3
Attach the pouch to the
pump/adapter and express. Keep the
pouch cap in a clean safe place so it
can be replaced after expressing
5
Pouches should be marked and dated
for reference using a soft tipped
marker so as not to damage the bag.
Depending on how the milk freezes in
the bag, you may not get an accurate
read so we recommend recording the
volume expressed in the 'notes' section
2. ASSEMBLING THE POUCH HOLDER
1 2
Leaving hood on teat, attach to
screw ring adapter
4
Place pouch in to the holder
and click in to place. Ensure the
measurement markings are
facing outwards - remove
screw cap once in place
5 a
Ensure all pouch holder and teat
parts have been washed and sterilised
as per guidelines before use
3
Screw the assembled ring and
teat to the pouch and holder
5 b
The pouch bottle is now ready
to use
When ready to feed, remove hood. Always ensure the pouch is upward facing.
Once feed is finished dispose of pouch and wash/sterilise all other parts as per
manufacturers guidelines
Loading...