advanced comfort
INSTRUCTIONS FOR USE
A
N
T
PRODUCT ASSEMBLY
A venting tube
B venting wheel
C valve
D teat
E screw ring
A
C
I
L
O
I
C
-
C
I
N
L
T
O
I
C
-
bottle and teat
A
C
I
N
L
T
O
I
C
-
fast flowmed flowslow flow
D
E
B
A
C
For cleaning other bottle parts, use a closer to
3
nature teat & spout brush.
Once you have cleaned your bottles they are ready
3
to sterilise.
All bottle components should be sterilised.
3
All bottle components are suitable for sterilisation
3
by steam (electric or microwave), boiling or cold
water tablet / liquid sterilisation.
Do not clean with harsh chemicals.
7
Do not allow product to come into contact with oil
7
based foods (e.g. oil / tomato based sauces) as
staining will occur.
Do not turn the teat inside out for cleaning.
7
Damage could result.
Do not use a teat brush or any other implement to
7
clean the feeding hole in the end of the teat or
valve as damage such as splits and tears may occur.
STORAGE & USE
Inspect before each use and pull the feeding teat in
3
all directions. Throw away at the first signs of
damage or weakness.
Keep all components not in use out of reach of
3
children.
For safety and hygiene reasons it is recommended
3
that the feeding teat is replaced every 2 months.
Do not store or leave in direct sunlight or near a
7
source of heat or leave in disinfectant (“Sterilising
Solution”) for longer than recommended, as this
may weaken the teat.
Do not store with or allow to come into contact
7
with solvents or harsh chemicals.
Not suitable for use in a conventional oven or a
7
combination microwave oven with the grill feature
switched on.
Do not heat in a microwave with bottle sealed.
7
Remove teat, locking ring and dome cap.
QUICK START:
1
Before use, wash all parts in warm soapy water,
rinse in clean water and sterilise.
Assemble your bottle as per the above diagram
2
3
When assembling your bottle it is important that
you check the valve (C) by holding it to the light to
check that the slit in the silicone has not sealed
closed. If it has sealed closed, pinch it gently
between your fingers to re-open. If the valve has
sealed closed your bottle will not vent properly.
Before each use, hold up to the
light to see the slit and pinch
apart to ensure proper venting.
Make up your feed
4
Serve
5
After use, wash all parts in warm soapy water, rinse
6
in clean water, ready to sterilise once more.
CLEANING & STERILISING
Before first use, clean the product.
3
Always wash the product immediately after use.
3
Clean before each use.
3
Before first use place in boiling water for 5 minutes
3
this is to ensure hygiene.
Wash in warm soapy water and rinse and rinse in
3
clean water or use a dish washer (top shelf only).
Ensure that you take apart the venting wheel (B)
3
and venting tube (A) and clean thoroughly with the
brush provided.
WARNINGS
FOR YOUR CHILDS SAFETY & HEALTH
WARNING!
Always use this product with adult supervision.
3
Accidents have occurred when babies have been
left alone with drinking equipment due to the baby
falling or if the product has been disassembled.
Always check food temperatures before feeding.
3
Heating in a microwave oven may produce localised
high temperatures. Take extra care when microwave
heating.
Always stir heated food to ensure even heat
3
distribution and test the temperature before
serving.
When making up a feed, follow the formula milk
3
manufacturer’s instructions and allow the freshly
boiled water to cool before pouring it into the
bottle.
Never use feeding teats as a soother.
7
Continuous and prolonged sucking of fluids will
7
cause tooth decay. Tooth decay in young children
can occur even when non-sweetened fluids are
used. This can occur if the baby is allowed to use the
bottle for long periods through the day and
particularly through the night, when saliva flow is
reduced or if it is used as a soother.
tommeetippee.com
Mayborn Baby and Child
Northumberland Business Park West
Cramlington Northumberland NE23 7RH, UK
Mayborn Baby and Child
is a trading style of Jackel International Limited.
Copyright© Jackel International Limited 2012.
0422601
Loading...