TOKO TK70001MCB Datasheet
TK70001
01S
SINGLE INPUT, TWO OUTPUT SOLID STATE SWITCH
FEATURES
■ Internal PNP Power Transistor
■ Reverse Bias Voltage Protection
■ Very Low Input-Output Voltage Difference
■ Very Low Standby Current
■ Overtemperature Protection
■ Single Input with Two Controlled Outputs
■ Low Noise
DESCRIPTION
The TK70001 is a monolithic bipolar integrated circuit with
high side current switches of low saturation type. The
current, including the control current, is zero (pA level)
when the control pin is “off”. The impedance on the output
side is high and the reverse current does not flow when the
control pin is “off”. These are effective to decrease the
dissipation currents, making the TK70001 a very efficient
device for power management and power distribution
control.
APPLICATIONS
■ Battery Powered Systems
■ Radio Control Systems
■ Automatic Test Equipment (ATE)
■ Power Management
■ Process Control Equipment
■ Power Distribution Control
■ Communication Equipment
TK70001
OUTPUT 1
INPUT
OUTPUT 2
CONT 1
GND
CONT 2
The TK70001 is available in a miniature SOT-26 surface
mount package. When mounted as recommended, this
package is capable of dissipating up to 350 mW.
ORDERING INFORMATION
TK70001MCB
Tape/Reel Code
TAPE/REEL CODE
B: Tape Left
OUTPUT 2
CONT 2
BLOCK DIAGRAM
INPUT
THERMAL
PROTECTION
SW
CIRCUIT
GND
OUTPUT 1
CONT 1
January 1999 TOKO, Inc. Page 1
TK70001
ABSOLUTE MAXIMUM RATINGS
Supply Voltage ......................................................... 14 V
Output Current .................................................... 130 mA
Power Dissipation (Note 1) ................................ 350 mW
Storage Temperature Range ................... -55 to +150 °C
TK70001 ELECTRICAL CHARACTERISTICS
Test conditions: T
LOBMYSRETEMARAPSNOITIDNOCTSETNIMPYTXAMSTINU
= 25 °C, V
A
= 2.5 V, unless otherwise specified.
IN
Operating Temperature Range ...................-30 to +80 °C
Operating Voltage Range............................... 1.6 to 12 V
Junction Temperature .......................................... 150 °C
Lead Soldering Temperature (10 s) ..................... 235 °C
I
Q
I
I
I
V
∆V
I
YBTS
TUO
DNG
PORD
D
VER
tnerruCtnecseiuQI
tnerruCybdnatS
tnerruCtuptuO
)3etoN(tnerruCdnuorGI
egatloVtuoporDI
slennahCneewteBecnalaB
tnerruCsaiBesreveR
TUO
V
NI
V
TNOC
V
PORD
V
PORD
TUO
TUO
V
PORD
I
TUO
V
NI
V
TNOC
I,Am0=
TNOC
Aµ05=6.02.1Am
,FFOtuptuO,V8=
V0=
I,V5.0=
TNOC
I,V5.0=
TNOC
I,Am05=
TNOC
I,Am05=
TNOC
Aµ05=06001Am
Aµ001=08031Am
Aµ05=5.35.5Am
Aµ05=71.053.0V
,ecnereffid
I,Am05=
TNOC
V,V0=
VER
Aµ05=
,V8=
FFOtuptuO,V0=
1.0001An
05Vm
20.005An
LANIMRETLORTNOCFFO/NO
I
TNOC
V
V
Note 1: Power dissipation is 350 mW when mounted as recommended. Derate at 2.8 mW/°C for operation above 25°C. Power dissipation is
Note 2: By grounding this terminal, the operation completely stops and the input current decreases to a pA level.
Note 3: Ground current is defined as IIN - I
Gen. Note: Parameters with min. or max. values are 100% tested.
Gen. Note: Exceeding “Absolute Maximum Ratings” can damage the device.
)NO(TNOC
)FFO(TNOC
150 mW in Free Air. Derate at 1.2 mW/°C for operation above 25 °C.
tnerruClanimreTlortnoCV
TNOC
I,V6.1=
TUO
Am05=0559041Aµ
)NO(egatloVlortnoCNOtuptuO0.1V
)FFO(egatloVlortnoC)2etoN(FFOtuptuO2.0V
, excluding control terminal current. Refer to “Definition of Terms.”
OUT
Page 2 January 1999 TOKO, Inc.
TEST CIRCUIT
INPUT
V
OUT 2
V
CONT 2
V
I
CONT 2
IN
I
OUT 2
C
L 2
R
OUTPUT 2
= 0.1 µF
CONT 2
I
IN
OUTPUT 1
C
CONT 1CONT 2
R
C
IN
1 µF
= 0.1 µF
L 1
CONT 1
I
CONT 1
I
OUT 1
V
CONT 1
V
OUT 1
TYPICAL PERFORMANCE CHARACTERISTICS
TK70001
DROPOUT VOLTAGE
CONTROL CURRENT
400
300
(mV)
200
DROP
V
75 mA
50 mA
100
I
= 25 mA
OUT
0
0 50 100
I
(
CONT
A)
DROPOUT VOLTAGE
OUTPUT CURRENT
0
100
(mV)
200
DROP
300
V
400
V
= 1 V
IN
V
IN
V
= 2.5 V
0 50 100 150
I
(mA)
OUT
VS.
125 mA
100 mA
VS.
= 5.0 V
IN
CONTROL CURRENT VS.
CONTROL VOLTAGE
100
20K
80
60
( A)
40
CONT
I
R
CONT
10K
= 0
20
0
0 1 2 3 4 5
V
(V)
CONT
QUIESCENT CURRENT VS.
INPUT VOLTAGE
500
( A)
250
Q
I
0
0 5 10 15
I
I
CONT
I
CONT
V
IN
I
CONT
I
CONT
CONT
= 20 A
= 10 A
(V)
30K
50K
75K
100K
= 50 A
= 40 A
= 30 A
MAX OUTPUT CURRENT VS.
CONTROL CURRENT
140
100
(mA)
60
OUT
I
20
V
VIN = 3.0 V
VIN = 4.5 V
VIN = 6.0 V
10 20 30 40 50
I
(
CONT
A)
REVERSE CURRENT
REVERSE VOLTAGE
2
(nA)
1
REV
I
0
0 5 10 15
V
(V)
REV
IN
= 1.5 V
VS.
January 1999 TOKO, Inc. Page 3
Loading...